Built-in Ice Maker IB450BL Owner’s Manual For more information on other great EdgeStar products on the web, go to http://www.edgestar.com V1.
Important Safety Information Improper handling can cause serious damage to the EdgeStar ice maker and/or injury to the user. This ice maker is designed for domestic indoor use only. Do not use the unit for industrial or commercial use. Any other use may invalidate the warranty. Please review the ratings label located on the rear panel of the unit for electrical and other technical data related to this unit. The unit must be used in a properly grounded wall outlet.
General Safety • • • • • • • • • • • • • • • • • • • • To prevent back and other types of injuries, use at least two people to move and install the ice maker. Install the ice maker in a well ventilated area where the ambient temperature is above 50° F and below 100° F. This unit is designed to be installed indoors, and protected from rain, sleet, snow, etc. This unit is not intended to be used by children. Children should be supervised to ensure that they do not play with this product.
Table of Contents IMPORTANT SAFETY INFORMATION............................................. II TABLE OF CONTENTS ................................................................... IV INTRODUCTION ................................................................................ 1 PARTS IDENTIFICATION .................................................................. 2 BACK VIEW ........................................................................................... 2 FRONT VIEW ...........................
Introduction Thank you for purchasing this EdgeStar built in ice maker. We hope that this purchase will be the beginning of a lasting and rewarding relationship between you and EdgeStar. We will provide the customer support and exemplary products necessary to nurture that relationship. This manual contains important information regarding the proper installation, use and maintenance of your ice maker. Following this manual will ensure that your product will work at its peak performance and efficiency.
Parts Identification Front View Back View 2
Installing the Ice Maker Warning: Use two or more people to move and install the ice maker. Failure to do so can result in back or other injury. The ice maker should be installed by a licensed plumber in accordance with local electrical and plumbing code requirements. Before you plug the ice maker in, be sure to let it stand upright for at least 24 hours to allow the compressor’s oils to settle.
Installation Clearance Requirements Note: This icemaker should be installed by a licensed plumber only. • To ensure proper service access and ventilation, allow more than 2” of clearance at the rear, and 1/4” at the top and at the sides. The installation should allow the icemaker to be pulled forward for servicing if necessary. • When installing the ice maker under a counter, follow the recommended spacing dimensions shown.
Electrical Requirements Electrical Shock Hazard • Plug into a grounded 3-prong outlet. • Never remove the grounding prong from the plug. • Never use an adapter. • Never use an extension cord. • Failure to follow these instructions can result in fire, electrical shock, or death Before you move your icemaker into its final location, it is important to make sure you have the proper electrical connection: A standard electrical supply (115 V, 60Hz.
Leveling the Ice Maker It is important for the icemaker to be leveled in order to work properly. It can be raised or lowered by rotating the four feet on the bottom of the machine. If you find that the surface is not level, rotate the feet until the ice maker becomes level. You may need to make several adjustments to level it. We recommend using a carpenter’s level to check the machine. 1. Place a carpenter’s level on top of the icemaker to see if it is level from front to back and side to side. 2.
Water Supply and Drain Connections The water supply should be ready at the point of installation. The water supply pressure should be a minimum of 15 psi with a static pressure of no more than 80 psi. (A wall outlet directly behind the ice maker will make installation easier.) When you connect the water supply hose and drain hose, pay attention to the label on the back that indicates the location of the water inlet and water outlet. Important: 1.
Operation Final Check List before Operation 1. Have all packing materials and tape been removed from the interior and exterior of the ice maker? 2. Did you clean the ice storage bin? 3. Have the installation instructions been followed, including connecting the machine to water and electricity? Does the unit have proper drainage? 4. Has the machine been leveled? 5.
How the Machine Makes Ice Turn the ICE/OFF/WASH switch to the ICE position. The machine will automatically start the ice making stage. There are two distinct cycles: freeze and harvest. During the freeze cycle, water flows across the evaporator surface to form the ice. In the harvest cycle, the ice is released. A complete cycle can take 15 to 40 minutes, depending on temperature and operating conditions.
Control Panel (rear of unit) 1. Ice Full (Red) LED: Ice Full indicator light. When this LED is lit, the ice storage bin is full of ice or there is something obstructing the ice slide. The unit will stop producing ice. When ice cubes are removed from the ice storage bin, clearing the ice slide, the red LED will keep flashing for 3 minutes. Then the unit will restart and return to the ice making mode. 2. Ice Making (Green) LED: Ice Making indicator light.
Normal Sounds Your new icemaker may make sounds that are not familiar to you. Most of the new sounds are normal. Hard surfaces like the floor and walls can make the sounds seem louder than they actually are. The following describes the kinds of sounds that might be new to you and what may be making them. • Rattling noises may come from the flow of the refrigerant or the water line. Items stored on top of the icemaker can also make noises.
What Should be Kept Clean? There are 5 things to keep clean: 1. The exterior 2. The ice bin and water trough 3. The condenser 4. The water distribution tube 5. The ice-making system Warning: Before proceeding with cleaning and maintenance operations, make sure the power line of the unit is disconnected and the water line is shut off.
Condenser Cleaning A dirty or clogged condenser prevents proper airflow, reduces ice making capacity, and causes higher than recommended operating temperatures that may lead to component failure. Have the condenser cleaned at least once every six months. 1. Unplug the ice maker or disconnect power. 2. Remove the 2 screws at the bottom of the front cover and gently pull it off. 3. Locate the condenser directly behind the front cover. 4.
Ice-making System Cleaning Caution: • Many ice machine cleaners contain acids. • DO NOT use or mix with any other solvent-based cleaner products. • Use rubber gloves to protect your hands. • Carefully read all safety instructions printed on the container of the ice machine cleaner. • Discard the first batch of ice produced after cleaning Minerals that are removed from water during the freezing cycle will eventually form a hard scaly deposit in the water system.
Issue The machine won't operate. The water doesn't feed in after the icemaker starts. The machine makes ice, but the bin does not fill up with ice. Water is leaking out of the unit. Possible Cause The icemaker is unplugged. The breaker is tripped. The icemaker power switch is OFF. The ice storage bin is full of ice. The water supply tap is turned off. The water supply pipe is not properly connected. The condenser may be dirty. The air flow to the ice maker may be obstructed.
Specifications Note: Technical data and performance information are provided for reference only. Description of product Built-in Ice Maker Model IB450BL Voltage/Frequency AC 115V~60Hz Ice-Making / Ice-Harvest rated current 3.0A / 4.0A Color Black Ice Storage capacity 25 lbs. maximum Ice-making capability 50 lbs. / day * Refrigerant R134a, 3.88 oz. High / Low side pressure 350 psi / 130 psi Dimensions (Width x Depth x Height) 14 9/16” x 23 3/8” x 32 9/16” Net Weight 76.7 lbs.
EdgeStar Limited Warranty Full One-year Parts and Labor WHAT IS COVERED: This product is warranted by EdgeStar and is subject to any conditions set forth as follows: For a period of ONE (1) YEAR from the date of original retail purchase, EdgeStar will repair or replace any part free of charge including labor that fails due to a defect in materials or workmanship.
