FS150 Hand-held Portable Scarifiers Parts & User Manual FS150.T.FlexHD FS150.T.Makita FS150.T.PN MANUFACTURING Cutters / Removers / Parts / Support (954) 941-9744 www.SMITHMFG .com 1-800-653-9311 www.SmithMfg.
FS150 INDEX Page Contents 2 Index / Introduction 3 Required Safety Equipment / Safety Guidelines (PNEUMATIC) 4 Your FS150 PNEUMATIC Hand held scarifier 5 Using the FS150 properly (PNEUMATIC) 6 Maintenance checklist / Safety Guidelines (ELECTRIC) 7 Your FS150 ELECTRIC Hand held scarifier 8 Using the FS150 properly (ELECTRIC) 9-10 Drum and cutter options, drum assembly 11 Operating Guideline 12 Maintenance Log 13-14 Warranty Information INTRODUCTION Congratulations on purchasing the
FS150 REQUIRED SAFETY EQUIPMENT SAFETY GUIDELINES -PNEUMATIC• • • When using this tool the following safety equipment MUST be worn! If you do not have this DO NOT USE THE MACHINE • • • • SAFETY GLASSES • • • SAFETY GLOVES • • • Read all instructions before using the tool. all operators must be fully trained in its use and aware of these safety rules.
FS150 YOUR PNEUMATIC FS150TM HAND HELD SCARIFIER ASSEMBLY (FS150.T.PN) Please take time to familiarize yourself with the FS150™’s controls, as well as some of the features of your new machine 1 2 4 3 6 5 7 8 9 Item: 10, 10* 11 P/N Qty Description 1 FS050.P 1 Pneumatic grinder 2 FS150.006 1 Collar for pneumatic grinder 3 FS150.000.T 1 FS150 housing assembly 4 FS150.004 1 Vacuum cap 5 FS150.830.3160A 1 Adapter mount 6 FS150.475.3282.5 3 Flat washer 7 FS150.475.3282.
FS150 RECOMMENDATIONS • Recommended working pressure: 6.3 bar / 90 psi • Maximum working pressure: 7.0 bar / 100 psi • Recommended hose bore: 10mm / 3/8” • Recommended hose length: 10m / 30 ft USING THE FS150 AIR SUPPLY: Use clean lubricated air supply that will give a measured air pressure at the tool of 6.3 bar / 90 psi when the tool is running with the trigger/lever depressed. Use the recommended hose size and length.
FS150 MAINTENANCE CHECK LIST SAFETY GUIDELINES -ELECTRIC• Before beginning servicing on any FS150 unit, DISCONNECT FROM AIR SUPPLY SOURCE • Check all fasteners and re-tighten, since the machine will vibrate the fasteners loose if they are not secured. Use locktight. • Clean drum housing regularly to prevent material buildup. • Inspect drum, and shafts for damage and replace as needed. • Regularly lubricate grinder with a suitable pneumatic motor lubricating oil.
FS150 YOUR ELECTRIC FS150TM HAND HELD SCARIFIER ASSEMBLY Please take time to familiarize yourself with the FS150™’s controls, as well as some of the features of your new machine 1, 1* 2, 2* 4 3 6 5 7 8 9 10, 10* P/N Qty Description 1 FS050.FXHD 1 FLEX grinder 1* FS050.ME 1 Makita grinder 2 FS150.475.3282.FX 1 Collar for FLEX grinder 2* FS150.475.3282 1 Collar for Makita grinder 3 FS150.000.T 1 FS150 housing assembly 4 FS150.004 1 Vacuum cap 5 FS150.830.
FS150 RECOMMENDATIONS • USING THE FS150 • ELECTRICAL SAFETY: Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adaptor plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.
DRUM OPTIONS A variety of cutters are available for the FS150 to suit all your removal needs. FLAIL-IT SCRAPE-IT Available in: Available in: CF1519 - 8-spike extended-tip ultra-premium-life tungsten carbide cutter FS150 CF0411 - 15-edge star, 100% sintered ultra-premium-life tungsten carbide cutter FINE FINISH 7-SHAFTED FINE FINISH 7-SHAFTED Drum assembly: FS150.1519.F Drum assembly: FS150.0411.F Rebuild kit: FS150.1519.F.RK Rebuild kit: FS150.0411.F.
FS150 DRUM ASSEMBLY PIN RETAINER PIN (7) DRUM MAIN BODY 10 SMITH Manufacturing 1-954-941-9744 www.SmithMfg.
FS150 The FS050 and FS150 are heavy duty commercial grade removal attachments connected to a light duty consumer grade right angle electric or pneumatic 3000 RPM polisher/sander in an effort to produce an affordable entry level scarifier for small jobs and detail surface preparation work. These systems will only operate to the limit of their weakest component. Using the unit as a reciprocating hammer or similar demolition tool will result in the failure of the polisher/sander.
FS150 MAINTENANCE LOG WARRANTY CLAIMS The manufacturer reserves the right to change or improve the machine design without assuming any obligation to update any products previously manufactured before this manual. It is the customer’s responsibility to complete the warranty card and mail it to the seller within 10 days from the date of purchase. If a failure occurs during the warranty period, the customer must contact the seller to determine the appropriate action.
Limited Equipment Warranty FS150 All statements, technical information and recommendations contained in SMITH’s literature are based on tests believed to be reliable, but the accuracy or completeness thereof is not guaranteed and the following is made in lieu of all warranties, expressed or implied.
FS150 Pre-Operation Inspection - Warranty Activation - Machine Registration Go to www.smithmfg.com/warranty_activation.php Thank you for purchasing a SMITH. This machine was tested and passed inspection prior to shipping. Please complete this form upon receipt of your equipment and prior to use on the job. Failure to do so will void warranty. All sections must be completed. Should you have any questions, please add to the comments section below.
SMITH Manufacturing 1610 South Dixie Highway Pompano Beach, FL 33060 Toll Free: 800.653.9311 Phone: 954.941.9744 Fax: 954.545.0348 Email: info@SmithMfg.com www.SmithMfg.
