Portable Ice Maker PIM300SS Owner’s Manual www.edgestar.com V1.
Important Safety Information Improper handling can cause serious damage to the EdgeStar ice maker and / or injury to the user. This ice maker is designed for domestic indoor use only. Do not use the unit for industrial or commercial use. Any other use may invalidate the warranty. Please review the ratings label located on the rear panel of the unit for electrical and other technical data related to this unit. The unit must be used in a properly grounded wall outlet.
Important Safety Information General Safety ! • To prevent injuries, use at least two people to move and install the ice maker. • This appliance is not intended for use by persons, including children, with reduced physical, sensory or mental capabilities, unless they have been given supervision or instruction concerning the use of the appliance by the person(s) responsible for their safety. • Install the ice maker in a well-ventilated area where the ambient temperature is above 50° F and below 90° F.
Table of Contents Important Safety Information........................................................................................... 2 First-Time Operating Instructions.................................................................................... 5 Introduction...................................................................................................................... 5 Parts Identification..................................................................................................
First-Time Operating Instructions Before use, make sure all packaging labels and materials are removed from the unit. Be sure to keep track of all included parts and pieces before discarding the packaging materials. It is advised that you keep the original box and packaging materials in case you ever need to move or ship the appliance in the future. Let the unit stand for at least 24 hours before you use it; this allows the cooling components time to settle from transit.
Parts Identification ! Note: Gather the model and serial number from the product label and write them down on the previous page before installing the ice maker.
Installation The ice maker should be installed in accordance with local electrical code requirements. The ice maker should also be placed in a location that is strong enough to support its total weight, keeping in mind that it will weigh substantially more when fully loaded with water and ice than when empty. Before you plug the ice maker into a power supply, be sure to let it stand upright for at least 24 hours to allow the compressor’s oils to settle.
Electrical Requirements ! ELECTRIC SHOCK HAZARD! • Plug into a grounded 3-prong outlet. • Never remove the grounding prong from the plug. • Never use an adapter to bypass the grounding prong. • DO NOT use an extension cord. • Failure to follow these instructions can result in fire, electrical shock, or death.
Operation Installation Checklist before Operation 1. Have all packing materials and tape been removed from the interior and exterior of the ice maker? 2. Have the installation instructions been followed, including connecting the machine to electricity? And has proper grounding been installed for the ice maker? 3. Is the ice maker in a site where the ambient temperature is between 50° F and 90° F all year round? 4. Has the unit been thoroughly cleaned prior to use? 5.
Control Panel Operation # 1 Feature Select Button 2 Timer Button 3 Clean Button 4 ON/OFF Button 5 LCD Display Window Symbol Displays the unit’s current settings and indicators. The backlight will shut off automatically a few seconds after pressing a button, but the unit is still operating normally. Indicator POWER Function Indicates whether the unit is plugged in to a power source. Does not shut off when the unit is powered off. ICE FULL Illuminates when the ice basket is full.
Timer Function The timer function allows you to either run the unit for a set amount of time before turning off or set a delayed start time. When the unit is turned off, you can set the timer to start ice production after a delay. 1). Press the TIMER button on the control panel. The timer indicator will flash on the LCD display. 2). Press the SELECT button to change the time delay to your desired value between 0.5 and 18 hours by 0.5 hour increments. 3).
How the Ice Maker Produces Ice After the unit is powered on, the ice maker rotates the ice case into the horizontal water fill position under the evaporator. The water pump is engaged and fills the ice case with water. Water overflows for a few seconds before the compressor turns on. The compressor then pumps refrigerant, and the fan will turn on automatically after the condenser heats up. The unit produces bullet shaped ice around the evaporator.
Draining the Unit Follow the steps below to drain the unit. 1. Carefully move the unit towards a sink or other suitable location for draining. 2. Unscrew the cap and remove the drain plug from the side of the unit to drain the water. 3. Firmly install the rubber drain plug into the drain port and replace the cap. ! Note: An extra drain plug is included with the unit. Cleaning and Maintenance Periodic cleaning and proper maintenance will ensure efficiency, top performance, and long life.
Troubleshooting Before Calling for Help: If the unit appears to be malfunctioning, read through the “Operation” section of this manual first. If the problem persists, check the Troubleshooting Guide below and on the following page. The problem may be something that can easily be solved or explained. Issue No Power Water is leaking out the unit. Noise during operation 14 Possible Cause The ice maker is unplugged. The ice maker power switch is OFF. Solution Plug the ice maker in. Press the power button.
Issue Unit goes through the ice making process, but no ice is produced, or ice cubes are very thin and small. Possible Cause The room temperature or water may be too hot. The unit is designed to work in a room that is above 50°F and below 90°F The fan may not be turning on to cool down the condenser coils. The “Add Water” light is on even The water filter may be clogged though the unit is full of water.
Specifications Product Type Portable Ice Maker Model PIM300SS Color Stainless Steel Voltage / Frequency AC 115V ~ 60Hz Amperage (Ice Making - Ice Harvesting) 2.0 - 2.7A Ice Storage Capacity 2.6 lbs Ice Making Capability Up to 48 lbs / day* Refrigerant R290 (1.16oz / 33g) Dimensions 14 15/16” x 17 1/8” x 17” (Width x Depth x Height) Net Weight 33 lbs 16 ! Note: The actual quantity of ice produced in a 24hour period will vary with room and water conditions.
EdgeStar Limited Warranty WHAT IS COVERED: One Year Parts & 90 Days Labor This product is warranted by EdgeStar and is subject to any conditions set forth as follows: LABOR: For a period of NINETY (90) DAYS from the date of original purchase, labor will be performed free of charge at an authorized EdgeStar repair facility. At its option, EdgeStar will repair the product with new or remanufactured parts, or exchange the defective product with a new, refurbished, or remanufactured product.
www.edgestar.
