IC-6220DC Quick Installation Guide 05-2016 / v1.
Package Contents Do not remove the sticker from the camera viewer until the bolt has been installed through your peep hole.
Reset If you experience problems with your network camera, you can reset the camera back to its factory default settings. This resets all settings back to default. Press and hold the Reset button on the back panel for at least 10 seconds. Release the button when the power LED is flashing quickly green, and wait a couple of minutes for the unit to restart.
LED Status Gateway: LED LED Color LED Status Description On Gateway is on and connected to cloud server. Power Green LAN Green Quick Flashing Gateway is restarting. Slow Flashing Gateway is starting up or is not connected to cloud server. Gateway is connected to the local network. On Quick Flashing Internet Orange LAN activity (transferring data). On Connected to Internet. Quick Flashing Slow Flashing (1 x per second) Gateway is restarting. Not connected to Internet.
Setup The door camera unit mounts conveniently and securely to your door’s peephole. Carefully remove any existing viewer/cover on your peephole before you begin. 1. Screw on the included antenna to the gateway unit and connect the power adapter. The green power LED will flash slowly when the gateway is ready. 2. Use an Ethernet cable to connect the gateway to your wireless router or access point.
4. To remove an existing peephole from your door, you can usually simply unscrew it using a coin. 5. Remove the warning sticker from the camera viewer. 6. Remove the sticker from the black double-sided tape on the camera viewer.
. From the front of your door, insert the camera viewer’s bolt through your door’s peephole until the unit is flush to your door. 8. Remove the plastic tube from the bolt. 9. From the inside of your door, screw on the included Installation Kit A (nut) onto the camera viewer’s bolt, until tight to your door.
10. Screw on the included Installation Kit B (washer) onto the camera unit’s bolt. 11. Connect the cable to the terminal on the camera battery unit. 12. Place the camera battery unit onto the viewer unit’s bolt with the battery side facing away from the door, and then screw the included Installation Kit C (cap) onto the bolt to secure the battery unit in place.
13. Switch the camera’s power switch on and re-attach the cover by twisting into place.
EdiLife App 1. Use a smartphone or tablet to search, download and install the EdiLife app from Google Play or the Apple App Store. 2. Open the EdiLife app and tap the + icon in the top right corner of the screen.
3. Select your camera from the available device list and wait a moment for the app to make a connection. Tap refresh in the top right corner if your camera isn’t listed. 4. For better security, enter a new device name and password when prompted. Tap the check mark to continue.
5. Setup is complete. Your camera should be listed on the EdiLife home screen. Tap your camera to see a live stream which you can view anytime you are connected to the Internet. You can configure your camera’s settings and functions using the icons below the live image. 6. If you have a microSD card, insert the card into the microSD slot on the back on the gateway unit.
Using Your Door Camera As well as the EdiLife app, you can use the camera’s web-based management interface to see a live stream and to configure the camera’s functions such as motion and sound detection. Go to the camera’s IP address in a web browser on a computer connected to the same local network: You can find your camera’s IP address using EdiView Finder on a computer, or using the EdiLife smartphone app (go to Settings). Check the user manual for help.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1995/95/EC, 2011/65/EC. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 1995/95/CE, 2011/65/CE. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 1995/95/ES, 2011/65/ES.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European R&TTE directive (1999/5/EC, 2006/95/EC) . Equipment: Model No.: Wireless Door Camera IC-6220DC The following European standards for essential requirements have been followed: Spectrum: EMC: EMF: Safety (LVD): ETSI EN 300 328 V1.9.1 (2015-02) EN 301 489-1 V1.9.2 (2011-09); EN 301 489-17 V2.2.
Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code.
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.
Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions.
