Quick Installation Guide AC900 Outdoor AP Quick Installation Guide 05‐2016 / v1.
I. Product Information I‐1. Package Contents 1 2 3 4 6 5 1. 2. 3. 4. 7 8 5. 6. 7. 8. Access Point Passive PoE Injector Quick Installation Guide Ethernet Cable Power Cord Power Adapter Wall Mount Screws Kits Pole Mount Ties I‐2.
I‐3. Hardware Overview C SMA A LAN1 (PoE‐IN) A. B. C. D. E. B LAN2 (PoE‐OUT) D Reset Button C SMA E PoE‐OUT On/Off LAN1 port with Power over Ethernet (Passive PoE‐IN). LAN2 port with Power over Ethernet (Passive PoE‐OUT). SMA connector for optional external antenna. Reset Button. Switch the LAN2 (Passive PoE‐OUT) On/Off. (Default: Off, Turn Right) I‐4. LED Status Power LAN 1 & 2 Wireless (Client mode only) Blue Off Blue Flashing Off Blue Off LED Behavior The access point is on.
I‐5 5. Reset p s with yo our accesss point, you y can reset the e device If you expeerience problems ettings baack to deefault. baack to itss factory settings.. This ressets all se 1. Press and a hold d the reseet button n on the access point for aat least 10 1 second ds. Then release the t butto on. You may need Yo n to use a penccil or simiilar sharp p object tto push th he reeset butto on. 2. Wait for f the acccess poiint to resstart. The e access point is rready forr setup when the t LED is i blue.
Pole Mount 1. Fix the access point to a pole using the included stainless tie. Attention: This product is installed in restricted access location by professionals. II. Quick Setup The AC900 Long Range 802.11ac Outdoor AP/CPE features a range of powerful functions: ‐ 802.11ac high‐speed wireless technology ‐ 16 SSIDs for management ‐ SNMP v1/v2c/v3 Your access point can be up and running in just a few minutes.
II‐‐1. Initial Setup Do not con D nnect a non‐PoE n d device to the accesss point’ss LAN2 (PoE‐ O OUT) port.. The LAN N2 port outputs 48 8V and ca an damag ge a non PoE d device. 1. Connect the acccess point’s LAN1 (PoE‐INN) port too the PoEE injector’s PoE port via Ethernet cable.. 2. Connect the PooE injectoor to a poower souurce usinng the inccluded poower nt for thee access point to start up.. The acccess point adapteer. Wait a momen is ready when the t Poweer LED is blue.
II‐2. AP Mode 1. Enter the access point’s IP address into the URL bar of a web browser. The default IP is 192.168.2.2. If the AP is connected to a DHCP server, ensure you use the correct address. 2. You will be prompted for a user name and password. Enter the default username “admin” and the default password “1234”. 3. You will arrive at the “System Information” screen shown below.
‐ ‐ ‐ ‐ A LAN IP Address 5GHz SSSID & Seecurity Adminiistrator Name N & Passworrd Time & Date Itt is recom mmended you conffigure theese settin ngs beforee using th he access poiint. 1. To chaange the access point’s p LA AN IP add dress, go o to “Netw work Setttings” > “LAN‐siide IP Ad ddress” and a you will w see the t screeen below. 2. Enter the t IP ad ddress seettings yo ou wish to t use forr your acccess point.
4 4. To con nfigure th he security of you ur accesss point’s 5GHz wireless ne etwork(s), go to “W Wireless Settingss” > “5GH Hz 11ac 11an” 1 > “Security “ y”. Select an “Authentication n Method d” and en nter a “P Pre‐shareed Key” o or “Encryption Key” depend ding on your choice, then click “Ap pply”. Iff using mu ultiple SSSIDs, speccify which h SSID to configuree using th he “SSSID” dro op down menu. m 5.
6. Complete the “Adminisstrator Name” N an nd “Administrator Passwo ord” field ds and clicck “Applyy”. 7. To set the corrrect timee for yourr access point, go o to “Managemen nt” > “Date and a Time e Settings”. 8. Set thee correctt time an nd time zone z for your y acceess pointt using th he drop down menus. m Th he access point also a supp ports NTP P (Netwo ork Time Protocoll) so alterrnatively you can enter th he host name or IP addresss of a tim me serveer.
III. Hardware Specification Hardware Specification MCU/RF MEDIATEK MT7621A (MCU) + QCA9882 (5GHz) Memory DDR3 128MB Flash 16MB Physical Interface ‐ LAN : 2 x Gigabit Ethernet with PoE support 48V passive PD‐IN (LAN 1); Pass‐through 48V passive PSE‐OUT (LAN 2) ‐ Reset Button ‐ Slide Switch (LAN 2 PSE‐OUT Power On/Off) ‐ SMA Connector x 2 : for External Antennas: Type: PCB Antenna Model name: C059‐690332‐FOD Manufacturer: WHA YU Industrial Co., Ltd. Gain:12.
1 x Passive PoE Injector (for indoor use) ‐ Operation Temperature: ‐30 to 50℃ ‐ Output: 48V,1A 1 x Power Adapter & Power Cord (for indoor use) ‐ Operation Temperature: ‐30 to 50℃ 12
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
