Quick Installation Guide AC1300 Outdoor AP GAP-429HOB Quick Installation Guide 05-2016 / v1.
I. Product Information I-1. Package Contents 1 2 4 1. 2. 3. 4. 3 5 6 5. 6.
I-2. System Requirements - Existing Ethernet cable, IEEE802.3at PoE Switch - Computer with web browser for access point configuration I-3. Hardware Overview B A C A. B. C. D. D LAN1 port with Power over Ethernet (IEEE802.3at PoE PD-IN). LAN2 port with Power over Ethernet (IEEE802.3af PoE PSE-OUT). Reset Button. Grounding Terminal.
I-4. LED Status 5G 2.4G LAN2(PSE) LAN1(PD) Status Power ON Off ON Off ON Flashing Off ON Flashing Off ON Off ON Flashing Off LED Behavior 5G Wireless is enabled. 5G Wireless is disabled. 2.4G Wireless is enabled. 2.4G Wireless is disabled. LAN2 port is connected. Traffic is passing through Ethernet port. LAN2 port is unconnected. LAN1 port is connected. Traffic is passing through Ethernet port. LAN1 port is unconnected. Booting up process No error occur The access point is on.
I-5. Reset If you experience problems with your access point, you can reset the device back to its factory settings. This resets all settings back to default. 1. Press and hold the reset button on the access point for at least 10 seconds. Then release the button. You may need to use a pencil or similar sharp object to push the reset button. 2. Wait for the access point to restart. The access point is ready for setup when the Status LED is OFF. I-6.
Pole Mount 1. Fix the access point to a pole using the included stainless tie. Attention: This product is installed in restricted access location by professionals. II. Quick Setup The AC1300 Outdoor AP/CPE features a range of powerful functions: - AC1300 high-speed wireless technology - 16 SSIDs for management - SNMP v1/v2c/v3 Your access point can be up and running in just a few minutes.
II-1. Initial Setup Do not connect a non-PoE device to the access point’s LAN2 (PoEOUT) port. The LAN2 port outputs 48V and can damage a non PoE device. 1. Connect the access point’s LAN1 (PoE-IN) port to the PoE Switch via Ethernet cable. 2. Wait a moment for the access point to start up. The access point is ready when the Status LED is OFF. 3. Use an Ethernet cable to connect your computer to the access point’s LAN2 port for initial setup.
II-2. AP Mode 1. Enter the access point’s IP address into the URL bar of a web browser. The default IP is 192.168.2.2. If the AP is connected to a DHCP server, ensure you use the correct address. 2. You will be prompted for a user name and password. Enter the default username “admin” and the default password “1234”. 3. You will arrive at the “System Information” screen shown below.
- LAN IP Address 2.4G/5GHz SSID & Security Administrator Name & Password Time & Date It is recommended you configure these settings before using the access point. 1. To change the access point’s LAN IP address, go to “Network Settings” > “LAN-side IP Address” and you will see the screen below. 2. Enter the IP address settings you wish to use for your access point. You can use a dynamic (DHCP) or static IP address, depending on your network environment.
Then enter a new SSID in the corresponding numbered fields below, before clicking “Apply”. 4. To configure the security of your access point’s 5GHz wireless network(s), go to “Wireless Settings” > “5GHz 11ac 11an” > “Security”. Select an “Authentication Method” and enter a “Pre-shared Key” or “Encryption Key” depending on your choice, then click “Apply”. If using multiple SSIDs, specify which SSID to configure using the “SSID” drop down menu.
5.To change the SSID of your access point’s 2.4GHz wireless network(s), go to “Wireless Settings” > “2.4GHz 11ac” > “Basic”. Enter the new SSID for your 5GHz wireless network in the “SSID1” field and click “Apply”. To utilize multiple 2.4GHz SSIDs, open the drop down menu labelled “Enable SSID number” and select how many SSIDs you require. Then enter a new SSID in the corresponding numbered fields below, before clicking “Apply”. 6.To configure the security of your access point’s 2.
If using multiple SSIDs, specify which SSID to configure using the “SSID” drop down menu. 7. To change the administrator name and password for the browser based configuration interface, go to “Management” > “Admin”. 8. Complete the “Administrator Name” and “Administrator Password” fields and click “Apply”. 9. To set the correct time for your access point, go to “Management” > “Date and Time Settings”.
10. Set the correct time and time zone for your access point using the drop down menus. The access point also supports NTP (Network Time Protocol) so alternatively you can enter the host name or IP address of a time server. Click “Apply” when you are finished. You can use the “Acquire Current Time from your PC” button if you wish to set the access point to the same time as your PC. 11. The basic settings of your access point are now configured.
III. Hardware Specification Hardware Specification MCU/RF Qualcomm Atheros IPQ 4018 Quad-Core 710MHz Memory DDR3 256MB Flash SPI NOR 32MB Physical Interface - LAN1: Gigabit Ethernet with IEEE802.3at PoE PD-IN support - LAN2: Gigabit Ethernet with IEEE802.3af PoE PSE-OUT support - Reset Button x 1 - Grounding Terminal x 1 - RP-SMA Connector x 2 Power Requirement IEEE802.3at Power over Ethernet Antenna External Dual Band Dipole Antenna x 2 (2.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
