V‐1‐3. Windows 7 1. Click the “Start” button (it should be located in the lower‐left corner of your computer), then click “Control Panel”. 2. Under “Network and Internet” click “View network status and tasks”. 3. Click “Local Area Connection”.
4. Click “Properties”.
5. Select “Internet Protocol Version 4 (TCP/IPv4) and then click “Properties”. 6. Select “Use the following IP address”, then input the following values: IP address: 192.168.2.10 Subnet Mask: 255.255.255.0 Click ‘OK’ when finished.
198
V‐1‐4. Windows 8 1. From the Windows 8 Start screen, you need to switch to desktop mode. Move your curser to the bottom left of the screen and click. 2. In desktop mode, click the File Explorer icon in the bottom left of the screen, as shown below.
3. Right click “Network” and then select “Properties”. 4. In the window that opens, select “Change adapter settings” from the left side.
5. 6. Choose your connection and right click, then select “Properties”. Select “Internet Protocol Version 4 (TCP/IPv4) and then click “Properties”.
7. Select “Use the following IP address”, then input the following values: IP address: 192.168.2.10 Subnet Mask: 255.255.255.0 Click ‘OK’ when finished.
V‐1‐5. Mac 1. Have your Macintosh computer operate as usual, and click on “System Preferences” 2. In System Preferences, click on “Network”. 3. Click on “Ethernet” in the left panel. 4. Open the drop‐down menu labeled “Configure IPv4” and select “Manually”.
5. Enter the IP address 192.168.2.10 and subnet mask 255.255.255.0. Click on “Apply” to save the changes.
V. Best Practice VI‐1. How to Create and Link WLAN & Access Point Groups You can use NMS to create individual SSIDs and group multiple SSIDs together into WLAN groups. You can then assign individual access points to use those WLAN group settings and/or group multiple access points together into access point groups, which you can also assign to use WLAN group settings. Follow the example below to: A. Create a WLAN group. B. Create an access point group. C.
3. The new SSID will be displayed in the WLAN panel. Repeat to add additional SSIDs according to your preference, and then click “Add” in the WLAN Group panel: 4. Enter a name for the SSID group and check the boxes to select which SSIDs to include within the group. Click “Apply” when done.
5. The new WLAN group will be displayed in the WLAN Group panel. Repeat to add additional WLAN groups according to your preference: B. 1.
2. Enter a Name and then scroll down to the Group Settings panel and use the << button to add selected access points into your group from the box on the right side. Click “Apply” when done. 3. The new access point group will be displayed in the Access Point Group panel.
C. 1. Go to NMS Settings Access Point and select an access point group using the checkboxes in the Access Point Group panel.
2. Scroll down to the Profile Group Settings panel and check the “Override Group Settings” box for WLAN Group (2.4GHz and/or 5GHz). Select your WLAN group from the drop‐down menu and click “Apply”: 3. Repeat for other access point groups according to your preference.
COPYRIGHT Copyright © Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU, 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2014/53/EU, 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European RED directives. Equipment: AC1300 DBDC Ceiling‐mount AP Model No.: CAP1300, Office 1‐2‐3, Office +1, Office +3, Office WiFi System, Office WiFi System +1 The following European standards for essential requirements have been followed: Directives 2014/53/EU Spectrum EMC : : ETSI EN 300 328 V2.1.1 (2016-11); EN 301 489-1 V2.1.
Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine‐readable copy of the corresponding source code.
intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2.
Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions.
