AR-7025Um ADSL USB Modem Quick Installation Guide December 2006 0
Copyright© by Edimax Technology Co, LTD. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company.
1. Hardware Indicators 1.1 LED Descriptions z When modem is establishing the connection, the LED will be blinking. z When modem is connected, the LED will be on steadily. 1.2 Front Panel Connect this connector with Type-B end of USB cable. 1.3 Rear Panel Connect this connector with RJ-11 cable. 2. Package Contains Open the shipping carton and carefully remove all items.
. Driver Installation 4.1 Before You Start The following information may be required for software installation. Contact your DSL service provider before proceeding with software installation. • IP Address Settings – the software installation process allows the server to dynamically assign IP Address settings.
Step 2: Insert “ADSL MODEM Driver CD”, the front page of Easy Setup window will be appeared, Install Driver: Click here to install USB ADSL modem driver. User Manual “Conexant AccessRunner USB ADSL”: Click here to read user’s manual. Acrobat: Click here to install Acrobat Reader 6.0. Panda: Click here to start Anti Virus program.
Step 3: Click “Install Driver”, and then select the country you are at, PS. If your country is not on the list, please click “*” to next page. Select “Other”, and then go to Step 10 to set your modem.
Step 4: After country selecting, the window below will appear. Select the appropriate ISP, and then click “``” to next page.
Step 6: Confirm modem settings and click “``” to next page, Step 7: Software kit searches available USB modem, 7
Step 8: The Installing window will be displayed indicating that the drivers are being installed. Step 9: The system must be rebooted to have the new settings take effect. [For Windows XP, 2000, and ME] In Windows XP, 2000, and ME Operating System, the Easy Setup program will automatically reboot your computer. Once the PC has rebooted, Installation of the USB Modem is completed. The Finished window will be displayed indicating the installation has been completed. Click “Finish”.
[For Windows 98SE] For Widows 98SE, during the installation process, the system will ask you to insert Windows 98SE installation CD, please insert the CD and click “OK”. The Reboot window will appear. Remove all disks from their drives, select “Yes, reboot the computer now”, and click “Close” to reboot. Once the PC has rebooted, the Finished window will be displayed indicating the installation has been completed. Click “Finish”.
Step 10: If your country is not on the list, please click “*” to next page and select “Other”, a) After you select ”Other”, the window below will appear, you must refer to the following table before you select the connection type, Connection Type WAN LAN Encapsulation and Multiplexing method Network Information PPP over ATM LLC (RFC 2364) Internet Account information: PPP over ATM NULL (RFC 2364) z User name PPP over Ethernet (RFC 2516) z Password Classical IP over ATM (RFC 1577) TCP/IP info
b) After you select the connection type, the window below will appear, and then confirm modem settings. All settings here are default, it might not correct settings for your connection, double check your ISP for the settings and go to “Accessing Communication Settings on Windows” to modify the settings.
4.3 Accessing Communication Settings on Windows Step 1: From your PC desktop, click StartÆProgramÆConexant DSL ModemÆ Configure. Step 2: The “Communication Settings” Window will be displayed. Make the necessary changes to the VPI, VCI, Encapsulation type and/or Modulation type and click “Next>”.
Step 3: The system must be rebooted to have the new settings take effect, therefore the Reboot window will appear. Remove all disks from their drives, select “Yes, reboot the computer now”, and click Close to reboot. PS. For the detail information, please refer to the manual in the provided CD.
Federal Communication Commission Interference Statement FCC Part 68 This equipment complies with Part 68 of the FCC Rules. On the bottom of this equipment is a label that contains the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. You must provide this information to the telephone company upon request. The REN is useful to determine the quantity of devices you may connect to the telephone line and still have all of those devices ring when your number is called.
Federal Communication Commission (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
