COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
CONTENTS CHAPTER I: INTRODUCTION ............................................................................................................................... 4 1-1 Package Contents ................................................................................................................................ 6 1-2 Safety Information ............................................................................................................................... 6 1-3 LED and Interface Description ..........
3-6-6-1 IGMP Proxy .................................................................................................................. 40 3-6-6-2 UPNP............................................................................................................................ 41 3-6-6-3 Advance \ Bridge ......................................................................................................... 41 3-6-6-4 Port Mapping.................................................................................
CHAPTER I: INTRODUCTION Thank you for purchasing this Edimax product. This router is a cost-effective router, an ADSL2+ modem, and Ethernet network switch. You can surf the Internet and share the connection through the router without investing in other devices. This router can support downstream transmission rates of up to 24Mbps and upstream transmission rates of up to 1Mbps.
5
1-1 Package Contents One single port router One external splitter One power adapter Two pieces of telephone lines(RJ-11,more than 1.8m) One piece of Ethernet cable(RJ-45, more than 1.8m) One piece of USB cable One copy of Quick Installation Guide One copy of driver and utility software CD (optional) 1-2 Safety Information Follow these announcements below to protect the device from risks and damage caused by fire or electric power. Use volume labels to mark the type of power.
1-3 LED and Interface Description Front Panel LED Power Color Green/ Red ADSL Green Internet Green LAN Green USB Green Status OFF GREEN RED RED BLINK OFF BLINK ON OFF BLINK ON OFF BLINK ON OFF ON Description Device not powered Device correctly powered Device not correctly powered Upgrade firmware Initial self-test failed Detecting ADSL Initial self-test complete Internet connection not established Internet activity (transferring data) Internet connection established LAN port not connected LAN ac
Rear Panel Item Line Reset Ethernet PWR USB Usage Line RJ-11 port Resets device to factory defaults (to restore factory defaults, push a paper clip into the hole when the device is powered and hold for over 5 seconds) Ethernet RJ-45 port Power ON/OFF Power connector (connects to DC12V 500mA power adapter) Connects to computer via USB cable (USB driver installation required. See APPENDIX A for details.
CHAPTER II: HARDWARE SETUP 1. Connect the “Line” port of the router and the “Modem” port of the splitter with a telephone (RJ-11) cable. 2. Connect the “Ethernet” port of the router to a computer via an Ethernet cable (MDI/MDIX). 3. Plug the power adapter to a wall outlet and then connect the other end to the “Power” port of the router.
CHAPTER III: WEB CONFIGURATION 3-1 Connecting to broadband router via web browser You can access the broadband router’s web-based configuration interface via any connected computer with a web browser (Internet Explorer 5.x or above, Firefox, Opera, or Safari). 1. Please input “192.168.2.1” in the web browser’s address bar and press “Enter”. 2. You should see the following authentication window.
3. Please input “admin” in the “User name” field and “1234” in the “Password” field. Click the “OK” button to enter the web configuration interface.
3-2 Status Click “Status” in the menu to open the sub-menu that contains 5 items: System, LAN, WAN, Statistic, and ARP Table. 3-2-1 System Click “System” in the sub-menu to open the following screen. In this page, you can view the status and some basic settings of this router, for example, Software Version, DSL mode, Upstream Speed, Downstream Speed, Uptime and so on.
3-2-2 LAN Click “LAN” in the sub-menu to open the following screen. In this page, you can view the LAN IP, DHCP Server status, MAC Address and DHCP Client Table.
3-2-3 WAN Click “WAN” in the sub-menu to open the following screen. In this page, you can view basic status of WAN, Default Gateway, and DNS Server.
3-2-4 Statistics Click “Statistics” in the sub-menu to open the menu in the left bar that contains two items: Traffic Statistics and DSL Statistics. 3-2-4-1 Traffic Statistics Click “Traffic Statistic” in the left bar to open the following screen. In this page, you can view the statistics of each network port.
3-2-4-2 DSL Statistics Click “DSL Statistics” in the left bar to open the following screen. In this page, you can view the ADSL line statistics, downstream rate, and upstream rate.
3-2-5 ARP Table Click “ARP Table” in the sub-menu to open the following screen. In this page, you can view the table that shows a list of learned MAC addresses.
3-3 Wizard The setup wizard enables speedy and accurate configuration of your Internet connection and other important parameters. The following sections describe these various configuration parameters. Whether you configure these parameters or use the default ones, click “Next” to enable your Internet connection. When subscribing to a broadband service, you should be aware of the method by which you are connected to the Internet. Your physical WAN device can be either Ethernet, DSL, or both.
Then press Next, the Fig 3.3.1-2 screen will appear. In this page, you can select the WAN Connect Type and the encapsulation method. Fig 3.3.1-2 If you finish the settings of this page, click Next, the screen appears as shown next. Fig 3.3.
3-4 Network \ LAN Click LAN in the menu to open the sub-menu which contains 2 items: LAN Settings and DHCP Settings. You can use the LAN configuration to define an IP address for the DSL Router and configure the DHCP server. 3-4-1 LAN Settings On this screen you can change the device's IP address. The preset IP address is 192.168.1.1. This is the Private IP address of the DSL Router. This is the address under which the device can be reached in the local network.
The following table describes the fields of this screen. Label IP Address Subnet Mask Secondary IP Apply Changes Description Input the IP of Local area network interface here. We recommend that you use an address from a block that is reserved for private use. This address block is 192.168.1.1- 192.168.255.254 Select this checkbox to enable the secondary LAN IP. The two LAN IP must be in the different network. Click this button to save the settings of this page.
If you set to DHCP Proxy, the screen of Fig 3.4.2-2 appears. Fig 3.4.2-2 The following table describes the fields of this screen. Label DHCP Proxy DHCP Server Address Apply Changes Description If set to DHCP Proxy, your ROUTER acts a surrogate DHCP Server and relays the DHCP requests and reponses between the remote server and the client. Enter the IP address of the actual, remote DHCP server in this field. Click this button to save the changes of this page.
If you set to DHCP Server, the screen of Fig3.4.2-3 appears as shown next. Fig 3.4.2-3 The following table describes the fields in this screen. Label DHCP Server IP Pool Range Show Client Max Lease Time Domain Name Gateway Address MAC-Base Assignment Apply Changes Description If set to DHCP Server, your ROUTER can assign IP addresses, an IP default gateway and DNS Servers to Windows95, Windows NT and other systems that support the DHCP client.
Click Show Client, the following window appears. In this window, you can view the IP address assigned to each DHCP client. Fig 3.4.2-4 The following table describes the fields in this screen. Label IP Address MAC Address Time Expired(s) Refresh Close Description This field displays the IP address relative to the MAC address. This field displays the MAC(Media Access Control) address of the computer. Every Ethernet device has a unique MAC address.
Click MAC-Base Assignment button, the below window appears. In this page, you can assign IP addresses on the LAN to specific individual computers based on their MAC address. Fig 3.4.2-5 The following table describes the fields of this screen. Label Host MAC Address Assigned IP Address Assign IP Modify Assigned IP Delete Assigned IP Close MAC-Base Assignment Table Description Type the MAC address of a computer on your LAN This field specifics the IP of the IP address pool.
3-5 Network \ WAN Click WAN Interface in the menu to open the sub-menu which contains 3 items: WAN Interface, ATM Settings and ADSL Settings. 3-5-1 WAN Interface Click WAN Interface in the sub-menu to open the screen of Fig 3.5.1-1. In this page, you can configure WAN Interface of your router. Fig 3.5.
VCI Encapsulation Channel Mode Admin Status Enable NAPT PPP Settings Login Name Password Connection Type Idle Time(min) WAN IP Settings Type Local IP Address Remote IP Address Subnet Mask Unnumbered Default Route Add points in an ATM network, and its valid value is from 0 to 255 The virtual channel between two points in an ATM network, ranging from 32 to 65535 (1 to 31 are reserved for known protocols) Choices are LLC and VC-Mux.
Modify Delete Selected VC Table. Select a PVC in the Current ATM VC Table, then modify the parameters of this PVC. When you finish, click this button to apply the change of this PVC. Select a PVC in the Current ATM VC Table, then click this button to delete this PVC. Click this button, the following screens will appear. In these pages, you can modify the PVCs’ parameters. 3-5-2 ATM Settings Click ATM Setting, the screen of Fig 3.5.1-3 will appear.
3-5-3 ADSL Settings Click ADSL Interface in the sub-menu to open the screen of Fig 3.5.2. In this page, you can select the DSL modulation. Mostly, the user just need to remain this factory default setting. Our modem support these modulations: G.Dmt, G.lite, T1.413, ADSL2, ADSL2+, AnnexL and AnnexM. The router will negotiate the modulation mode with the DSLAM. Fig 3.5.
3-6 Service & Advance Click Advance in the menu to open the sub-menu which contains 6 items: DNS, Firewall, Virtual Server, Routing, IP QOS, and Others. 3-6-1 DNS Click DNS in the sub-menu to open the menu in the left bar, whick contains two items:DNS Server and DDNS. 3-6-1-1 DNS Server Short for Domain Name System (or Service or Server), an Internet service that translates domain names into IP addresses. Because domain names are alphabetic, they're easier to remember.
Label Attain DNS Automatically Set DNS Manually Apply Changes Reset Selected Description When this checkbox is selected, this router will accept the first received DNS assignment from one of the PPPoA, PPPoE or MER enabled PVC(s) during the connection establishment. When this checkbox is selected, please enter the primary and optional secondary DNS server IP addresses. Click this button to save the settings of this page. Click this button to begin configuring this screen afresh.
3-6-2 Firewall Click Firewall in the sub-menu to open the menu in the left bar, whick contains three items:IP/Port Fileter, MAC Filter and URL Blocking. 3-6-2-1 IP/Port Filter Click IP/Port Filter in the left bar to open the screen of Fig 3.6.2.1. Entries in this table are used to restrict certain types of data packets through the Gateway. Use of such filters can be helpful in securing or restricting your local network. Click the button Apply Changes to save the settings of this page.
3-6-2-2 MAC Filter Click MAC Filter in the left bar to open the screen of Fig 3.6.2.2. Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway. Use of such filters can be helpful in securing or restricting your local network. Click the button Apply Changes to save the settings of this page. Click the button Add to add a new rule of the MAC Filter. Fig 3.6.2.
3-6-2-3 URL Blocking Click URL Blocking in the left bar to open the screen of Fig 3.6.2.3. This page is used to configure the Blocked FQDN(Such as tw.yahoo.com) and filtered keyword. Here you can add/delete FQDN and filtered keyword. Fig 3.6.2.
3-6-3 Firewall – II Click Virtual Server in the sub-menu to open the menu in the left bar,whick contains two items:Services and DMZ Settings. 3-6-3-1 Virtual Services Click Services in the left pane to open the screen of Fig 3.6.3.1. This page is used to enable the servers in the local network. Click the button Add to add a virtual server. Fig 3.6.3.
3-6-3-2 DMZ Settings Click DMZ Settings in the left bar to open the screen of Fig 3.6.3.2. A Demilitarized Zone is used to provide Internet services without sacrificing unauthorized access to its local private network. Typically, the DMZ host contains devices accessible to Internet traffic, such as Web (HTTP ) servers, FTP servers, SMTP (e-mail) servers and DNS servers. Select the checkbox Enable DMZ to enable this function. Then input a IP Address of the DMZ host.
3-6-4 Routing Click Routing in the sub-menu to open the menu in the left bar, whick contains two items: RIP and Static Route. 3-6-4-1 RIP Click RIP in the left bar to open the screen of Fig 3.6.4.1. Enable the RIP if you are using this device as a RIP-enabled router to communicate with others using the Routing Information Protocol. This page is used to select the interfaces on your deviceis that use RIP, and the version of the protocol used. Fig 3.6.4.
3-6-4-2 Static Route Click Static Route in the left bar to open the screen of Fig 3.6.4.2-1. This page is used to configure the routing information. Here you can add/delete IP routes. Fig 3.6.4.
3-6-5 IP QoS Click IP QoS in the sub-menu to open the screen of Fig 3.6.5. Entries in this table are used to assign the precedence for each incoming packet based on physical LAN port, TCP/UDP port number, and source/destination IP address/subnet masks. Click the button Apply Changes to save the settings of this page. Fig 3.6.
3-6-6 Service --II Click Others in the sub-menu to open the menu in the left bar,whick contains four items:IGMP Proxy, UPNP, Bridge and IP PassThrough. 3-6-6-1 IGMP Proxy Click IGMP Proxy in the left bar to open the screen of Fig 3.6.6.1. IGMP proxy enables the system to issue IGMP host messages on behalf of hosts that the system discovered through standard IGMP interfaces. The system acts as a proxy for its hosts after you enable it. Click Apply Changes to save the settings of this page. Fig 3.6.6.
3-6-6-2 UPNP Click UPNP in the left bar to open the screen of Fig 3.6.6.2. This page is used to configure UPnP. The system acts as a daemon after you enable it. Click Apply Changes to save the settings of this page. Fig 3.6.6.2 3-6-6-3 Advance \ Bridge Click Bridge in the left bar to open the screen of Fig 3.6.6.3-1. This page is used to configure the bridge parameters. Here you can change the settings or view some information on the bridge and its attached ports. Fig 3.6.6.
Click Show MACs button in Fig 3.6.6.3-1, the below window will appear. This table shows a list of learned MAC addresses for this bridge. Fig 3.6.6.3-2 3-6-6-4 Port Mapping Click Port Mapping in the left bar to open the screen of Fig 3.6.6.4. Fig 3.6.6.
3-6-6-5 SNMP Click SNMP in the sub-menu to open the screen of Fig 3.7.7. In this page, you can set the SNMP parameters. Fig 3.7.7 Label Trap IP Address Community name(read-only) Community name(write-only) Apply Changes Reset Description Input the Trap Host’s IP here. The trap information will be sent to this host. The network administrators must use this password to read the information of this router. The network administrators must use this password to configure the information of this router.
3-6-6-6 Service \ TR069 Click TR069 in the sub-menu to open the screen of Fig 3.7.8. In this page, you can configure the TR-069 CPE. Fig 3.7.
3-6-6-7 Service \ ACL Click ACL in the sub-menu to open the screen of Fig 3.7.9. In this page, you can configure the IP Address for Access Control List. If ACL enabled, only the effective IP in ACL can access ADSL Router. Step 1: If you want to enable ACL, please choose "Enable" then press "Apply Changes"; Step 2: Config Access Control List; Note: If you check "Enable" in ACL Capability, please make sure that your host IP is in ACL List before it takes effect Fig 3.7.
3-7 Admin Click Admin in the menu to open the sub-menu which contains 9 items: Remote Access, Commit/Reboot, Password, Backup/Restore, Upgrade Firmware, Time Zone, SNMP ,TR069 and ACL. 3-7-1 Commit/Reboot Click Commit/Reboot in the sub-menu to open the screen of Fig 3.7.2. In this page, you can set the router reboot to default settings or set the router save the current settings then reboot. Fig 3.7.2 Label Description Restore to Factory Select this checkbox to reset router to default settings.
3-7-2 Password Click Password in the sub-menu to open the screen of Fig 3.7.3. In this page, you can change the password of the user, include admin and user. The super user name and password are admin/admin as default, and the The common user name and password are user/user. Fig 3.7.3 Label User Name Description Select the user name in the drop-down list box. The choices are admin and user. Old Password After selected the user name, input the old password of the user here.
3-7-3 Backup/Restore Click Backup/Restore in the sub-menu to open the screen of Fig 3.7.4. In this page, you can backup the current settings to a file and restore the settings from the file which was saved previously. IMPORTANT! Do not turn off your router or press the Reset button while these procedures are in progress. Fig 3.7.4 Label Save Settings to File Load Settings from File Upload Description Click the Save button, then select the path and save the configuration file of your router.
3-7-4 Firmware Upgrade Click Upgrade Firmware in the sub-menu to open the screen of Fig 3.7.5. In this page, you can upgrade the firmware of this router. IMPORTANT! Do not turn off your router or press the Reset button while this procedure is in progress. Fig 3.7.5 Label Select File Upload Reset Description Click the Browse button to select the firmware file. Selected the firmware file, click Upload button to begin upgrading the firmware. Click this button to begin selecting the firmware file afresh.
3-7-5 Time Zone Click Time Zone in the sub-menu to open the screen of Fig 3.7.6. In this page, you can set the system time manually or get the system time from the time server. Fig 3.7.6 Label Refresh Time Mode Enable SNTP Client Update SNTP Server Time Zone Apply Changes Description Click this button to refresh the system shown in the page. If select Time Server, the router will get the system time from the time server. If select Manual, you should configure the system time manually.
3-8 Diagnostic Click Diagnostic in the menu to open the sub-menu which contains 4 items: Ping, ATM Loopback, ADSL and Diagnostic. 3-8-1 Ping Click Ping in the sub-menu to open the screen of Fig 3.8.1. Fig 3.8.1 Label Host Address Go! Description Enter the IP Address here. Click this button to begin to Ping the Host Address.
3-8-2 ATM Loopback Click ATM Loopback in the sub-menu to open the screen of Fig 3.8.2. In this page, you can use VCC loopback function to check the connectivity of the VCC. Fig 3.8.2 Go!: Click this button to begin testing. 3-8-3 ADSL Click ADSL in the sub-menu to open the screen of Fig 3.8.3. This page is used for ADSL Tone Diagnostics.
Fig 3.8.3 Start: Click this button to begin ADSL Tone Diagnostics. 3-8-4 Diagnostic Click Diagnostic in the sub-menu to open the screen of Fig 3.8.4. This page is used for testing your DSL connection. Fig 3.8.4 Run Diagnostic Test: Click this button to begin testing.
APPENDIX A: USB SOFTWARE SETUP Execute Setup.exe to startup InstallShield Wizard, Fig A-1 will be shown: Fig A-1 Then press Next, the Fig A-2 screen will appear. This window shows the rate of progress.
After Setup finished, Fig A-3 will be shown:connect or disconnect your ADSL MODEM to PC as follow prompt. Fig A-3 Before install driver program. You must confirm ADSL MODEM has been connected to computer via USB slot; Once the PC powers up, a new device will be will be detected by Windows . The computer will give a message finding new hardware. Fig A-4 will be shown.
Select “No, not this time” and press “Next”, Fig A-5 will be shown below: Fig A-5 56
Select “Install the software automatically (Recommended)” and then press “Next” button, Windows will search and find the USB driver and automatically install the driver. Fig A-6 will be shown: Fig A-6 Wait for a few seconds, Fig A-7 will be shown and you press “Finish” button to close the wizard, USB driver,installing is completely.
Fig A-7 58
APPENDIX B: ABBREVIATIONS ADSL ATM ATU C ATU R BER CO CPE CRC DC DSL HEC IDFT LOF LOS MIB Modem NMS OAM POTS PSTN PVC QAM SNR TP VPN Asymmetric Digital Subscriber Line Asynchronous Transfer Mode ATU at the central office end (i.e., network operator) ATU at the remote terminal end (i.e.
60
