PT-31E/PT-31W Quick Installation Guide 06-2012 / v1.
COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
PACKAGE CONTENTS Before you start using this product, please check if there is anything missing in the package, and contact your dealer to claim the missing item(s): 1 x Network camera 1 x Power adapter 1 x Ethernet cable 1 x Mounting kit 1 x CD with utility software and user manual 1 x Quick installation guide 1 x Detachable antenna (PT-31W only) HARDWARE INSTALLATION Please follow the instructions to set up your new network camera.
Step 2: Insert mounting plate B into the slot at the bottom of the network camera. Step 3: Screw mounting plate B to the network camera via the 2 holes indicated by the arrows. Step 4: Mount the network camera on to the wall.
Step 5: Screw mounting plate A and B together via the hole indicated by the arrow. Step 6: When mounted on the wall, the cables can pass through mounting plate A as shown in the diagram. Step 7: Connect an Ethernet cable to the network camera via the Ethernet port. Note: PT-31E (PoE model) supports the IEEE 802.3af PoE standard. It can be powered via the Ethernet cable when connected to a PoE switch.
Step 8: Insert the DI/DO signal cable(s) into the DI/DO port. If you do not have DI/DO accessories, you can skip this step. Step 9: Connect the power adapter to the network camera, then plug the power adapter into a wall socket. The camera’s LED lights should light up after a few seconds, and the camera will test its pan and tilt motor within 1 minute. Please do not obstruct the network camera while it is testing its pan and tilt motor.
ACCESSING THE NETWORK CAMERA’S MANAGEMENT INTERFACE By default, the network camera automatically obtains an IP address from the DHCP server on your local network. Check your DHCP server’s IP address lease table to find the network camera’s IP address, or use the EdiView Finder utility included in the CD. Note: We recommend that you use Microsoft Windows to install your network camera - Mac is not supported. 1. Insert the CD into your CD-ROM drive.
2. After the installation is complete, double-click the “EdiView_Finder” icon to execute the application. 3. Click “Discover” to search for all the network cameras on your local network (make sure all the network cameras are powered on and connected to the network first). 4. When you find a network camera, left click on it once and click “Link” to access it via the web browser.
6. The browser might ask you to install the ActiveX plug-in. Allow the browser to install the plug-in when prompted or you will not be able to see the video from the network camera. For IE 8 and earlier versions: For IE 9, the notification will be displayed at the bottom of Internet Explorer: Click ‘Allow’ to install ActiveX plug-in. If you’re prompted “Windows Firewall has blocked some features of this program” then click ‘Allow access’, or the pan-tilt camera will not be able to function properly.
When you’re installing Internet Explorer plug-in, you may also be asked if you want to allow changes to be made to your computer: Click “Yes” to allow changes. After ActiveX plug-in is installed, you should be able to see the video stream from the camera. Please refer to the user manual for more detailed instructions.
Wireless Setting Wi-Fi Connection using WPS Method 1: WPS BUTTON Step 1: Power on the wireless AP and the wireless network camera. Wait for 1 minute for both devices to be up and running. Step 2: Press the WPS button of the wireless AP. The WPS LED status will usually flash to indicate that WPS is active – but this is dependent on the brand of the AP. Step 3: Press the WPS button of the wireless network camera and wait for 30 seconds.
Method 2: PIN CODE SETTING Step 1: Power on the wireless AP and the wireless network camera. Wait for 1 minute for both devices to be up and running. Step 2: Open a web browser and login to the wireless server. Go to the wireless/WPS setting page. Step 3: Open web browser and login to the wireless network camera. Go to the network/Wireless setting page and locate Wi-Fi Protected Setup (WPS) item.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
EU Declaration of Conformity English: French: Czechian: Polish: Romanian: Russian: Magyar: Türkçe: Ukrainian: Slovakian: German: Spanish: Italian: Dutch: Portugese: Norwegian: Swedish: Danish: Finnish: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC, 2006/95/EC. Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2004/108/EC, 2006/95/EC.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European directive 2004/108/EC and 2006/95/EC. Equipment: 3Mpx PoE Day & Night PT Network Camera Model No.: PT-31E Report No.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European R&TTE directive and EMC directive, ETSI. Equipment: 3Mpx Wireless Day & Night PT Network Camera Model No.: PT-31W Report No.: T110919202-RE1 The following European standards for essential requirements have been followed: ETSI EN 301 489-17 V2.1.1 2009-05 ETSI EN 301 489-1 V1.8.
Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code.
intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 7.
19
