AI-1001W V2, V3, V4 Quick Installation Guide 12-2019 / v1.
Contents I. Safety Information ...............................................1 II. Product Information .............................................2 II-1. Package Content .............................................................................. 2 II-2. LED Indicator ................................................................................... 3 II-3. Hardware Introduction .................................................................... 4 II-4. System Requirement .....................
I. Safety Information For effective sensing and retrieval of environmental data, please install the unit with the safety restrictions outlined below: 1. 2. 3. 4. 5. 6. 7. 8. Must be in locations with good air circulation. Must be positioned for proper air intake to achieve cross ventilation. The air inlet must be kept clear and should be rechecked regularly. Must be in locations close to a power supply and has good Wi-Fi internet signal capable of connecting to the Internet 24 hours a day, 7 days a week.
II. Product Information The AI-1001W V2, V3 and V4 (4-in-1) Multi-Sensor Outdoor Air Quality Detector is your best air quality solution – with the EdiGreen Cloud Service, the AI-1001W V2, V3 and V4 provides a comprehensive air quality monitoring solution to help city governments to improve urban air quality. II-1.
II-2.
II-3.
II-4. No. Description 1 Reset Button 2 Micro USB Port (Power 5V/1A) 3 Fan 4 Sensor 5 LED Internet 6 LED Wi-Fi 7 LED Status System Requirement - Internet with Wi-Fi Connection 2.4G (802.
III.Hardware Installation This section will guide you through the steps to connect your air quality detector to the Internet. III-1. Airbox Installation 1. Please plug the power adapter to a power socket and connect the AI-1001W V2, V3, V4 using the USB cable. (The red status LED will turn on) 2. Please wait a moment for the device to boot up (red status LED will stay on during boot up). The red status LED and green internet LED will start flashing to indicate that factory default is completed.
III-2. Wall Bracket Installation The installation of wall-mount stand for AI-1001W V3, V4 is shown as figure below: III-3. Replace The PM 2.5 Sensor 1. Disconnect the AI-1001W V3, V4 from power. Then unplug the power adaptor before cleaning moderately. 2. Remove the bottom screws.
3. Carefully pull out the PM2.5 sensor. 4. After the ribbon cable is removed, take off the existing sensor and replace with the new one. Then install the new sensor in accordance with installation guideline stated above. Please remember the color orientation of the cable and insert the cable back according to its color orientation. During the removal of the sensor, please pull out the latch gently to prevent it from breaking off.
IV. EdiGreen App Installation Search and download "EdiGreen" in the Apple App Store or Google Play Store. Launch the "EdiGreen" in your smart mobile device. For the Internet connection procedure, please follow the instructions below, according to your mobile device. Please make sure "Access to my location" is turned on. Android OS iOS ˙ Your mobile device is able to connect to your home's Wi-Fi network or whichever network you anticipated the detector to connect to.
IV-1. EdiGreen Account First time users, please follow the steps below to register the EdiGreen account, 1. Tap the icon in the top right corner of the homepage. 2. Tap “Add New Device”.
3. Click on “Sign Up” below to register an account. 4. Enter a valid email and password. Validate your password again and tap “Next”. Please make sure the email address is valid.
5. Please check your email for a message with your code. (Your code is 6 numbers long). 6. Enter the 6 digits code and tap “OK“.
7. You will see “Setup Successful”, please tap “Ok”. 8. Enter your email and password. Login your account. NOTE: For how to reset the password, please refer to the manual for more detailed instructions.
IV-2. Adding Devices (Wi-Fi, Android) 1. Turn on Wi-Fi in your Android phone. 2. Open the EdiGreen App. 3. A pop-up Declaration and Statement will be displayed on screen, please press “AGREE” to continue.
4. Tap the icon in the top right corner of the homepage. 5. Tap “Add New Device”.
6. Select a model. 7. The app will start searching for available Wi-Fi network for the detector. Tap the desired Wi-Fi network.
8. Choose either “ACCURATE LOCATION” or “INACCURATE LOCATION”. 9. Enter a device name, password and validate the password again. NOTE: AI-1001W V4 does not have“device name/ password”page.
10. Select a Wi-Fi network. 11. Enter the Wi-Fi password and press “OK” to continue. Please find the unique SSID of your detector on the product label. The final two digits ** of the SSID "PM2.5_Setup_**" is the final two digits of the detector's “Setup WiFi SSID”.
Setup Complete! Now you are able to monitor the air quality near your unit, anywhere with your mobile device. IV-3. AI-1001W V4 (NB-IoT, Android) Please follow the steps below to add your AI-1001W V4 to the EdiGreen. 1. Select AI-1001W_V4.
2. Select the NB-IoT mode. 3. Select your device from the device list.
4. Choose “ACCURATE LOCATION” or “INACCURATE LOCATION”. Setup Complete! You are successfully connect to your AI-1001W V4 to EdiGreen via NB-IoT.
IV-4. Adding Devices (Wi-Fi, iOS) 1. Open the EdiGreen App. 2. A pop-up Statement and Declaration will be displayed on screen, please press “OK” and “Agree” to continue.
3. Tap the icon in the top right corner of the homepage. 4. Tap “Add New Device”.
5. Select a model. 6. Pop-up Wi-Fi Connection tutorial will be displayed on screen.
7. Go to Wi-Fi settings and choose the SSID “PM2.5_Setup_XX” of your detector. Please find the unique SSID of your detector on the product label. The final 2 digits ** of the SSID "PM2.5_Setup_**" is the final two digits of the detector's “Setup WiFi SSID”. 8. Open the EdiGreen again. Choose either”ACCURATE LOCATION” or “INACCURATE LOCATION”.
9. Enter a device name, password and validate the password again. NOTE: AI-1001W V4 does not have“device name/ password”page. 10. The app will start searching for available Wi-Fi network for the detector. Tap the desired Wi-Fi network and enter the Wi-Fi password and press “OK” to continue.
Setup Complete! Now you are able to monitor the air quality near your unit with your mobile device anywhere. IV-5. AI-1001W V4 (NB-IoT, iOS) Please follow the steps below to add your AI-1001W V4 to the EdiGreen. 1. Select AI-1001W_V4.
2. Select NB-IoT mode. 3. Pop-up Wi-Fi Connection tutorial will be displayed on screen.
4. Go to Wi-Fi settings and choose the SSID “PM2.5_Setup_XX” of your detector. Please find the unique SSID of your detector on the product label. The final 2 digits ** of the SSID "PM2.5_Setup_**" is the final two digits of the detector's “Setup WiFi SSID”. 5. Choose either “ACCURATE LOCATION” or “INACCURATE LOCATION”.
6. Open the EdiGreen again to start the installation. Setup complete! You are successfully connect to your AI-1001W V4 to EdiGreen via NB-IoT.
V. Reset to Factory Default Settings If you experience problems with the device, try rebooting it by reconnecting the power. If rebooting does not work, try resetting it back to its factory default settings. This resets all settings back to the default settings. To perform a factory reset, please follow steps below: 1. Press and hold the reset button on the back panel for at least 10 seconds.
VI. Cleaning the Unit Choose either of the two options below depending on the cleaning tool you have. It is recommended to clean the sensors every 3-6 months for optimal sensor functionality. If you have other pump-like cleaning tools available (e.g. for computers), you may also utilize them. Please be careful to not exert extremes of force or temperature / humidity onto the sensors to prevent damaging them. VI-1. Air Pump Cleaner 1. Direct the nozzle of the air pump cleaner at an opening of a sensor. 2.
VI-2. Dust-off Canned Compressed Air 1. 2. 3. 4. Direct the nozzle of the compressed air at an opening of a sensor. Keep the nozzle at 10cm from the sensor opening. Use short bursts (1-2 seconds) of air spray a few times to clean the sensor. Make sure all sensor openings are cleaned. A general dust-off compressed air will be sufficient.
COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
Federal Communication Commission Interference Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU, 2014/35/EU. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2014/53/EU, 2014/35/EU. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 2014/53/EU, 2014/35/EU.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European Radio Equipment directives. Equipment: Air Box Model No.: AI-1001W V2/V3 The following European standards for essential requirements have been followed: Directives 2014/53/EU Spectrum : EN 300 328 V2.1.1 (2016-11) EMC : EN 301 489-1 V2.2.0 (2017-03) EN 301 489-17 V3.2.
