AR-7287WnA Quick Installation Guide 04-2017 / v1.
PRODUCT INTRODUCTION Package Contents Before you start using this product, please check if there is anything missing in the package and contact your dealer to claim the missing item(s): ADSL2+ router (AR-7287WnA) 12V power adapter 1 meter RJ-45 Ethernet cable 1 meter RJ-11 telephone line x 2 Quick installation guide CD containing setup wizard, user manual & multi-language QIG Splitter System Requirements A 10/100 base-T Ethernet card installed in your PC.
LED Color Status Power Green On ADSL2+ router is on. Off ADSL2+ router is off. On ADSL line is synchronized and ready to use. ADSL Green Flashing Internet Green On Flashing LAN1–4 WLAN WPS Green Green Green ADSL line not synchronized. Internet connected in router mode Internet not connected in router mode Off Device in bridged mode. On LAN port connected. Off LAN port not connected. On Successful WLAN connection. Off WLAN connection failed. Off WPS is disabled.
Item Power On/Off Button Power Description Switches the router on or off. Power port for included 12V power adapter. Wireless / WPS *Hold for less than 5 seconds to enable wireless signal. Button *Hold for more than 5 seconds to activate WPS function. LAN 1–4 Reset Button Line RJ-45 Ethernet ports 1–4. Hold for less than 3 seconds to reset the device to factory default settings. RJ-11 port for standard telephone line.
GETTING STARTED A. Hardware Installation 1. Connect the ADSL line. Connect the line port of the router of the device to the modem interface of a splitter using a telephone cable. Connect a telephone to the Phone interface of the splitter using a telephone cable. Connect the Line interface of the splitter to your existing, incoming line. The splitter has three interfaces: Line: Connect to a wall phone jack (RJ-11 jack). Modem: Connect to the ADSL jack of the device. Phone: Connect to a telephone set.
can continue setup. However if the light is flashing, there is no broadband line detected. Please call your Internet Service Provider (ISP) and inform them about the flashing ADSL light to resolve the issue. 5. Firewall settings. Please turn off all personal firewalls before you continue the setup – firewalls can block communication between your PC and router. Note: You must use the power adapter included in the package with the router, do NOT attempt to use a third-party power adapter. 6.
4. Select the “Local Area Connection” icon and right-click it to open the sub-menu, then select “Properties”. 5. Select “Internet Protocol (TCP/IP)” and then click “Properties” 6.
server address automatically” are selected and then press “OK”. B. Internet Connection 1. Enter the router’s default IP address: “192.168.2.1” into your PC’s web browser and press “Enter”. 2. The login screen below will appear. Enter the default username “admin” and default password “1234” and click “OK”.
3. You will arrive at the system status page as shown below. 4. In the navigation bar across the top of the screen, click “Wizard” and then “Wizard”. The Wizard page of the web-based interface allows fast configuration of the Internet connection and other parameters. Please refer to the user manual for detailed information on these parameters.
5. Follow the on screen instructions until the wizard is complete.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2006/95/EC, 2011/65/EC. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2006/95/CE, 2011/65/CE. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 2006/95/ES, 2011/65/ES.
Declaration of Conformity We, Edimax Technology Co., LTD., declare under our sole responsibility, that the equipment described below complies with the requirements of the European Council directive (2014/53/EU). Equipment : Model No. : N300 Wireless ADSL2/2+ Modem router AR-7287WnA The following European standards for essential requirements have been followed: Spectrum : ETSI EN 300 328 : V2.1.1(2016-11) EMC : EN 301 489-1 V2.1.1(2017-02) EN 301 489-17 V3.1.
14
