BR-6478AC V3 Guide d'installation 12-2018 / v1.
Contenu de l'emballage Before you start using this product, please check if there is anything missing in the package, and contact your dealer to claim the missing item(s): BR-6478AC V3 Power Adapter Câble Ethernet Guide d'installation rapide CD-ROM Introduction 1. Branchez l'adaptateur secteur fourni dans la prise d'alimentation CC de l'appareil et branchez l'autre extrémité dans une prise de courant.
2. Plug the Ethernet cable into the device’s WAN port and the other end into a modem. Ensure that the five LEDs (power, Internet, 2.4GHz & 5GHz Wi-Fi & USB) display are on. Voyants Alimentation Couleur Vert Internet Vert 2.4G Wi-Fi Vert 5G Wi-Fi Vert USB Vert État du voyant Allumé L'appareil est sous tension. Éteint L'appareil est hors tension. Allumé La connexion Internet est prête.
Installation Use a Wi-Fi device (e.g. computer, tablet, smartphone) to search for a Wi-Fi network with the SSID “edimax_2.4G_xx or edimax_5G_xx ” and connect to it. After setup you can access the browser based configuration interface to configure or change the settings of the BR-6478AC V3. To access the browser based configuration interface, enter http:// 192.168.2.1 into the URL bar of a web browser on a network device which is connected to the BR-6478AC V3. If you can not access 192.168.2.
1. The Wizard Setup page screen appears as below. 2. Click Next and you can configure the router Operation Mode. 3. Click Next to configure Time Zone Setting.
4. Click Next and you can configure the LAN Interface Setup. This page is used to configure the parameters for local area network which connects to the LAN port of your Access Point. Here you may change the setting for IP address, subnet mask, DHCP, etc. 5. Click Next and you can configure the WAN Interface Setup. This page is used to configure the parameters for Internet network which connects to the WAN port of your Access Point.
. Click Next and configure the 5 GHz wireless network parameters. 8. Click Next and configure the 5 GHz wireless security. It should be set up at least 8 characters. 9. Click Next and configure the 2.4GHz wireless network parameters.
10. Click Next and configure the 2.4GHz wireless security. It should be set up at least 8 characters. And then click Finish. After initial set up is completed, use the top menu to navigate and click on “Settings” to select one of the three operation modes (Wi-Fi Router, Access Point and Wi-Fi Bridge) if you want to switch to different operation mode. Pour plus d'informations, consultez le manuel utilisateur.
Dépannage 1. How to set up the TCP/IP Protocol in Obtain an IP address automatically mode on your computer? a. A computer installed with a wired network adapter is used as an example here to describe the steps in Win 10 and in similar steps for the other systems. Étape 1. Right-click in the lower-right corner of the desktop and choose Open Network and Internet Setting. Step 2. Click Network and Sharing Center. Étape 3. Click Ethernet and Properties.
Étape 4. Double-click Internet Protocol Version 4 (TCP/IPv4). Étape 5. Select Obtain an IP address automatically and Obtain DNS server address automatically, and click OK. Étape 6. You'll go back to the Ethernet Properties box, please click OK.
2. Je ne parviens pas à ouvrir l'interface web de configuration. a. b. c. d. e. f. g. Make sure the connection of WAN and LAN port(s) is correct. Ensure that your Ethernet cable with internet connectivity is plugged into the WAN port of the router rather than a LAN port. Ensure that your wireless device is connected to the LAN port(s) of the router. Make sure you enter the correct IP address (192.168.2.1) to log in.
COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria, Belgium, Bulgaria, Cyprus, Czech, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Turkey, and United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and Switzerland.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU, 2014/35/EU. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2014/53/EU, 2014/35/EU. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 2014/53/EU, 2014/35/EU.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European Radio Equipment directives. Equipment: Model No.: AC1200 Wireless router BR-6478AC V3 The following European standards for essential requirements have been followed: Directives 2014/53/EU Spectrum : EN 300 328 V2.1.1:2016 EN 301 893 V2.1.1:2017 EMC : EN 301 489-1 V2.2.0:2017 EN 301 489-17 V3.2.
Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code.
intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 7.
