Office +1 Quick Installation Guide 11-2020 / v1.
I Quick Summary & Reminder 1. You can find all supporting documents, video, and programs: www.edimax.com/edimax_pro/download/Office1-2-3 2. For the complete Office 1-2-3 system introduction, please go to the link below: http://office123.edimax.com 3. There can be only one Office 1-2-3 master unit in the network. rest are Office +1. 4. During the initial power up, the master AP will automatically communicate its settings with all the Office +1 Access Points (~10 minutes). 5.
II Product Information II-1 1 Package Contents 3 2 6 5 4 7 1. 2. 3. 4. 8 5. 6. 7. 8.
II-2 System Requirements - Existing cable/DSL modem & router.
II-4 LED Status LED Color Blue Amber Off II-5 LED Status On Flashing Slowly Flashing Quickly On Flashing Off Description The access point is on. Upgrading firmware. Resetting to factory defaults. Starting up. Error. The access point is off. Reset If you experience problems with your access point, you can reset the device back to its factory settings. This resets all settings back to default. 1. Press and hold the reset button on the access point for at least 10 seconds then release the button.
III Adding Office +1 AP to Office 1-2-3 This quick setup is a guide to help you add the Office +1 AP to existing Office 1-2-3 high speed Wi-Fi network. 1. Identify the PoE Switch connected to existing Office 1-2-3 network. 2. Connect the Office +1 AP to the PoE Switch using an Ethernet cable. Please make sure the Ethernet cable is connected to the PoE port of the access point as shown below: If you need to, remove the cap from the underside of the access point.
IV Replacing Master AP NOTE: there can only be ONE Master AP inside your network. Use this procedure only if your master AP is down and need a replacement. This section will be a step-by-step procedure guiding you through replacing the original Master AP, where you will be upgrading to the Master AP’s firmware, followed by recovering previously saved system settings.
2. Locate your Office +1 AP by clicking “Discover” finder. 3. Click the IP address of the access point designated to be the master AP and go into the web user interface.
Upon entering the webpage, you should be prompted to enter the username and password, enter them (default username: admin, password: 1234) to proceed: The web user interface is shown below: 8
4. Click on “System Settings” icon. Upgrading Firmware 5. Scroll down to the bottom of the page to find “Firmware Upgrade”. If you haven’t already, please go to the URL link below to download the newest Master firmware: www.edimax.com/edimax_pro/download/Office1-2-3 Locate the Master firmware and click on the download icon to download. 6. Click “Choose File” to select the master firmware file. 7. Click “Update” to update the unit to the master firmware version.
A reminder message will be displayed, click “OK” to continue. The system will be updating, please wait… 8. After the firmware upgrade, the system will prompt you to enter the username and password, enter them (default username: admin, password: 1234) to proceed: 9.
More system message will be displayed, click “OK” to continue” The system is now rebooting, please wait… 10.
11. Click on “System Settings” icon. Restore Previous Settings 12. Scroll down to find “Firmware Upgrade”. 13. Click the “Choose File” button to find a previously saved settings file on your computer. 14. Click “Restore” to replace your current settings. If your settings file is encrypted with a password, check the “Open file with password” box and enter the password in the following field.
COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment. EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria, Belgium, Bulgaria, Cyprus, Czech, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Turkey, and United Kingdom.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU, 2014/35/EU. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2014/53/EU, 2014/35/EU. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 2014/53/EU, 2014/35/EU.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European Radio Equipment Directive. Equipment: AC1300 DBDC Ceiling-mount AP Model No.: Office +1 The following European standards for essential requirements have been followed: Directives 2014/53/EU Spectrum EMF : EN 300 328 V2.1.1 (2016-11) EN 301 893 V2.1.1 (2017-05) : Draft EN 301 489-1 V2.2.1 (2019-03) Draft EN 301 489-17 V3.2.
Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code.
intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2.
Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions.
