CV-7428nS Quick Installation Guide 09-2012 / v1.
Getting Started Before you start using the wireless bridge, please check if there’s anything missing in the package, and contact your dealer of purchase to claim any missing items. - CV-7428nS wireless bridge Power adapter Quick installation guide CD with multi-language QIG and user manual RJ45 Ethernet cable Access key card Top Panel LED Status Item Color Status On Description Wireless bridge is on. PWR (Power) Green Flashing Device is booting up. Off Wireless bridge is off.
(Wireless LAN) Flashing Slow Flashing Off Wireless network is off. On 1 to 5 (LAN Ports 1 to 5) Green LED will remain on for 5 minutes. WLAN activity – transferring or receiving data. WPS is activated and waiting for WPS connection. The LED will flash two seconds on, two seconds off. The wireless bridge will wait for a WPS connection for two minutes. Flashing Off Corresponding Ethernet port is connected to a device. Data is being transmitted through the Ethernet cable.
Connect computers or other network devices to these ports using an Ethernet cable. c. Power Port Connect the included 5V DC power adapter here. d. WPS/Reset Button Press and hold this button for 2 seconds to activate the WPS function. Press and hold this button for 10 seconds, until the PWR LED starts flashing, to reset the wireless bridge to factory default settings. Quick Installation There are two ways you can quickly setup your wireless bridge - using the WPS button or using iQ Setup on your computer.
Press for two seconds WLAN LED should flash slowly 3. The WPS function of the wireless bridge will now be active for 2 minutes. So, within 2 minutes, please press the WPS button on the wireless router/access point of your root network, to activate its WPS function also. Note: Different routers/access points may require you to press and hold the WPS button for different lengths of time – if you are unsure, please consult the user manual of your device.
4. A WPS connection will now be established between your wireless bridge and root network router/access point within two minutes. The WLAN LED will stop flashing, and display on to indicate a successful connection. The WLAN LED will remain on for 5 minutes. Note: If the WPS function on your wireless bridge timed out after 2 minutes, before you activated WPS on your router/access point, then please return to step 2 and try again.
3. Open a web browser, and you will be prompted for a username and password. Note: If you are not prompted for a username and password, please enter “http://edimax.go” into the URL bar. 4. Please enter the default username “admin” and the default password “1234”. Windows: Mac: 5. You will see the iQ Setup screen, as shown below. All available Wi-Fi networks will be listed – please select the Wi-Fi network you would like the wireless bridge to connect to.
Note: If you do not know your network security key, please refer to the user manual for guidance on how to find it. Note: If the Wi-Fi network you wish to connect to is not listed, try clicking “Refresh” to refresh the list. 6. Click “NEXT” to continue, and Internet Explorer and Firefox users will be asked to confirm if you wish to add “http://edimax.go” to your bookmarks. We recommend that you do so for future use.
7. Next, please wait while the wireless bridge tests the connection. 8. When the test has finished, the following screen will be displayed. Please click “NEXT” to continue. 9. The device name and security type will be displayed on the screen. Click “APPLY” to restart the wireless bridge and make the settings take effect, or click “Back” to go back to the previous screen.
. When you click “APPLY”, the system will restart. Please wait until the restart completes. 11. The following screen will confirm that your wireless bridge is connected to your Wi-Fi network, and the root AP name and security key will also be displayed. Your wireless bridge is now configured and ready for use with your wired network device, such as smart TV, Blu-ray player or games console. Please see Hardware Installation for guidance on using the wireless bridge with your network device.
Figure i Figure ii Resetting the Wireless Bridge In the event that the wireless bridge malfunctions or stops responding, you can reset the device back to its factory settings. To do so, press and hold the WPS/Reset button on the rear panel of the device for at least 10 seconds. When the green PWR LED begins to flash, release the WPS/Reset button and wait for the device to restart. The device is ready when the PWR LED has stopped flashing, and displays on.
COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC, 2006/95/EC. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 1999/5/CE, 2006/95/CE. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 1999/5/ES, 2006/95/ES.
Declaration of Conformity We, Edimax Technology Co., LTD., declare under our sole responsibility, that the equipment described below complies with the requirements of the European R&TTE directive (1999/5/EC, 2006/95/EC). Equipment: N300 Universal Wi-Fi Bridge Model No.: CV-7428nS Report No.: ER251556, EA251556, EH251556 The following European standards for essential requirements have been followed: Spectrum: ETSI EN 300 328 V1.7.1 (2006-10); EN 301 489-1 V1.9.2 (2011-09) EN 301 489-17 V2.1.
Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code.
intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 7.
