GS-5654LX & GS-5654PLX Quick Installation Guide 05-2021 / v1.
Contents I Product Information .................................................1 I-1 Package Content............................................................... 2 I-2 Hardware Overview ......................................................... 3 I-3 LED Status ....................................................................... 5 II Installation ..............................................................7 II-1 Mounting the Switch ........................................................
I Product Information The EDIMAX Pro GS-5654LX and GS-5654PLX fully utilizes the power of your office networking for demanding tasks, such as data backup, video conferencing, high volume transaction processing, large file transferring, and more. With smart features such as SNMP v1/v2/v3, PoE PD Alive Check, DHCP Snooping, QoS, CoS, STP, 802.
I-1 Package Content Before start using this product, please check if there is anything missing in the package, and contact your dealer to claim the missing item(s): GS-5654LX or GS-5654PLX Rack-Mount Kit & Screws QIG 2 Power Cord Console Cable
I-2 Hardware Overview GS-5654LX: 4 12 3 7 8 5 6 9 No.
GS-5654PLX: 9 5 12 3 4 6 7 11 10 No.
I-3 LED Status GS-5654LX: Function PWR SYS ALM SYS Link/ACT (1-48 port) SPF+ (49-54 port) Status On (Green) Off On (RED) Off On (Green) Off Blinking (Green) On (Green) Blinking (Green) On (Amber) Blinking (Amber) Off On (Green) On (Blue) Blinking (Green or Blue) Off Description Power on Power off System failure (Overheat, wrong voltage) Device in good condition Power on Power off System boot up Link at 1000M Sending or receiving data Link at 10/100M Sending or receiving data Port disconnected or link
GS-5654PLX: Function PWR SYS ALM SYS PoE Max Link/ACT (1-48 port) SPF+ (49-54 port) LED Slide Switch Status Description On (Green) Off On (RED) Off On (Green) Off Blinking (Green) On (Green) Off On (Green) Blinking (Green) On (Amber) Blinking (Amber) Off On (Green) On (Blue) Blinking (Green or Blue) Off Power on Power off System failure (Overheat, wrong voltage) Device in good condition Power on Power off System boot up Over PoE max power Not over PoE max power Link at 1000M Sending or receiving data
II Installation This chapter describes how to install and connect your Edimax Switch. Read the following topics and perform the procedures in the correct order. Incorrect installation may cause damage to the product. II-1 Mounting the Switch There are two ways to physically set up the switch. Place the switch on a flat surface. To place the switch on a desktop, install the four rubber feet (included) on the bottom of the switch. Mount the switch in a standard rack (1 rack unit high).
II-1-2 Rack Mounting You can mount the switch in any standard size, 19-inch (about 48 cm) wide rack. The switch requires 1 rack unit (RU) of space, which is 1.75 inches (44.45 mm) high. For stability, load the rack from the bottom to the top, with the heaviest devices on the bottom. A top-heavy rack is likely to be unstable and may tip over.
2. Secure the switch on the equipment rack with the screws provided.
III Getting Started This section provides an introduction to the web-based configuration utility, and covers the following topics: Powering on the device Connecting to the network Power over Ethernet (PoE) considerations Starting the web-based configuration utility III-1 III-1-1 Power Connecting to Power Power down and disconnect the power cord before servicing or wiring a switch. Do not disconnect modules or cabling unless the power is first switched off.
III-1-2 Connecting to Network To connect the switch to the network: 1. Connect an Ethernet cable to the Ethernet port of a computer. 2. Connect the other end of the Ethernet cable to LAN Port of the switch. The LED of the port lights if the device connected is active. 3. Connect an Ethernet cable to the IP Cameras Connect the switch to end nodes using a standard Cat5e Ethernet cable to connect the switch to end nodes as shown in the illustration below.
If you have multiple IPv6 interfaces on your management station, use the IPv6 global address instead of the IPv6 link local address to access the device from your browser. Launching the Configuration Utility Open the web-based configuration utility: 1. Open a Web browser. 2. Enter the IP address of the device you are configuring in the address bar on the browser (factory default IP address is 192.168.2.1) and then press Enter. 3. The default username is “admin” and the default password is “1234”. 4.
COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/30/EU. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2014/30/EU. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 2014/30/EU. Polski: Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami określonymi Dyrektywą UE 2014/30/EU.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European R&TTE directives. Equipment: 54 Gigabit ports Web-Smart Switch with 6 SFP+ 10 Gigabit Model No.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European R&TTE directives. Equipment: 54 Gigabit PoE ports Web-Smart Switch with 6 SFP+ 10 Gigabit Model No.
