IAP1200 Quick Installation Guide 05-2021 / v1.
I. Product Information I-1. Package Contents or IAP1200 (US) Quick Installation Guide IAP1200 (EU) Screws x 2 I-2.
I-3. Hardware Overview Reset Button RJ11 Pass-Through LEDs RJ45 Ethernet Port RJ45 Ethernet Port RJ11 Pass-Through I-4. LED Status LED LED Color Power (Right) Green LAN (Left) Green Green Orange Green & Orange Status On Flashing On Flashing Flashing Flashing/ Alternating Description The access point is on. The access point is starting up. LAN port is connected. LAN activity Locating access point. Upgrading firmware. Do not switch off.
I-5. Reset If you experience problems with your access point, you can reset the device back to its factory settings. This resets all settings back to default. 1. 2. Press and hold the reset button on the access point for at least 10 seconds. Then release the button. You may need to use a pencil or similar sharp object to push the reset button. Wait for the access point to restart. The access point is ready for setup when the green power LED is on. II. Quick Setup The IAP1200 Long Range 802.
II-1. AP Mode 1. Connect the IAP1200’s rear Ethernet port to a PoE switch (LAN port) using an Ethernet cable. 2. Use a computer that’s connected to the LAN or connect to the IAP1200’s front Ethernet port using an Ethernet cable. 3. Open a web browser and enter the access point’s IP address in the address field. The default IP address is 192.168.2.2 Your computer’s IP address must be in the same subnet as the AP access point. Refer to the user manual for more help.
4. Login with the default username & password: admin & 1234 5. You will arrive at the “System Information” screen shown below. The next steps will help you to configure the following basic settings of the access point: - LAN IP Address 2.4GHz & 5GHz SSID & Security Administrator Name & Password Time & Date It is recommended you configure these settings before using the access point. 1.
2. Enter the IP address settings you wish to use for your access point. You can use a dynamic (DHCP) or static IP address, depending on your network environment. Click “Apply” to save the changes and wait a few moments for the access point to reload. When you change your access point’s IP address, you need to use the new IP address to access the browser based configuration interface instead of the default IP 192.168.2.2. 3. To change the SSID of your access point’s 2.
4. To configure the security of your access point’s 2.4GHz wireless network(s), go to “Wireless Setting” > “2.4GHz 11bgn” > “Security”. Select an “Authentication Method” and enter a “Pre-shared Key” or “Encryption Key” depending on your choice, then click “Apply”. If using multiple SSIDs, specify which SSID to configure using the “SSID” drop down menu. 5. Go to “Wireless Settings” > “5GHz 11ac 11an” and repeat steps 3 & 4 for the access point’s 5GHz wireless network. 6.
. Set the correct time and time zone for your access point using the drop down menus. The access point also supports NTP (Network Time Protocol) so alternatively you can enter the host name or IP address of a time server. Click “Apply” when you are finished. You can use the “Acquire Current Time from your PC” button if you wish to set the access point to the same time as your PC. 10. The basic settings of your access point are now configured.
II-3. Managed AP Mode: Edimax Pro NMS Edimax Pro Network Management Suite (NMS) supports the central management of a group of access points, otherwise known as an AP Array. NMS supports up to 16 Edimax Pro access points with no additional wireless controller required or 128 access points with the APC 500 AP controller reducing costs and facilitating efficient remote AP management. Edimax Pro NMS is simple to setup.
When using an Edimax NMS AP controller, other connected APs are automatically set to Managed APs. In the case that the AP Controller cannot find your IAP1200 as a Managed AP, you can configure the setting manually as below: 1. Ensure all APs including your IAP1200 are connected to an Ethernet or PoE switch which is connected to a gateway/router. You can use your router as a DHCP server or you can later configure your AP Controller as a DHCP server. 2. Ensure all APs are powered on and check LEDs.
3. Connect the APC500 as the AP Controller which will manage all other connected APs (up to 128 depending on model). 4. Connect a computer to the IAP1200 via PoE switch using an Ethernet cable.
5. Open a web browser and enter the IAP1200’s IP address in the address field. The default IP address is 192.168.2.2 Your computer’s IP address must be in the same subnet as the AP Controller. If you changed the AP Controller’s IP address, or if your gateway/router uses a DHCP server, ensure you enter the correct IP address. Refer to your gateway/router’s settings. 6. Enter the username & password to login. The default username & password are admin & 1234. 7.
COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment. EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria, Belgium, Bulgaria, Cyprus, Czech, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Turkey, and United Kingdom.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU, 2014/35/EU. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2014/53/EU, 2014/35/EU. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 2014/53/EU, 2014/35/EU.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European Radio Equipment Directive. Equipment: In-Wall AP Model No.: IAP1200 The following European standards for essential requirements have been followed: Directives 2014/53/EU Spectrum EMF : EN 300 328 V2.1.1 (2016-11) EN 301 893 V2.1.1 (2017-05) : EN 301 489-1 V2.2.0 (2017-03) EN 301 489-17 V3.2.
Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code.
intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2.
Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions.
