IC-7113W User Manual 05-2015 / v1.
Copyright ＠ Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
I. Product Information .............................................................................. 6 I-1. Package Contents ....................................................................................................................6 I-2. I-3. I-4. I-5. I-6. I-7. System Requirements .............................................................................................................6 LED Status .............................................................................................
IV-4-1-1. Motion Detection..................................................................................................................60 IV-4-1-2.Detection Region ...................................................................................................................63 IV-4-1-3.Schedule Settings ...................................................................................................................65 IV-4-2. Sound Detection ........................................................
VI-3-2-1.General ................................................................................................................................111 VI-3-2-2.Email Settings ......................................................................................................................113 VI-3-2-3. Security ...............................................................................................................................115 VI-3-2-4.About ....................................................
I. Product Information I-1.
I-2. - System Requirements Intel Pentium 4 2.4GHz (above or similar) VGA card (1024*768 or above) CD-ROM Drive At least 128MB hard disk space (256 MB recommended) Windows XP, Vista, 7 or 8, Mac OS X Web browser (Internet Explorer 7.0, Firefox 3.
I-3. LED Status LED Color Red Green Off LED Status Description On Network camera is not connected to Internet. Quick Flashing Camera starting up or resetting to factory default status. Slow Flashing (1 x per Camera is in installation mode. second) Network camera is connected to the Internet On or WPS connection successful. Slow Flashing (1 x per 2 WPS is active. seconds) Off Camera is off.
I-4. Product Label The product label located on the underside of the network camera displays the serial number, MAC address, cloud ID and setup SSID of your network camera. The MAC address and cloud ID are the same for easy reference. The cloud ID allows you to view a live stream from your network camera remotely (from any Internet connection) as described later in V. Myedimax.com.
I-5. Reset If you experience problems with your network camera, you can reset the camera back to its factory default settings. This resets all settings back to default. 1.Press and hold the WPS/Reset button found on the back panel for at least 10 seconds. Release the button when the LED is flashing quickly red. 2. Wait for the network camera to restart. The camera is ready when the LED is flashing slowly red and plays an audio tone from its speaker.
I-6. Back Panel Antenna Environment Sensor LAN Port WPS/Reset microSD Slot 12 V 1 A Power Port LED I-7. Adjust Lens Focus To adjust the focus of your camera lens, turn the outer lens clockwise or anticlockwise according to your requirement.
II. Camera Setup Your network camera’s unique SSID is displayed on the product label on the product’s indoor main unit and consits of “EdiView.Setup**” where ** are the last two characters of your camera’s unique MAC address. 1.Connect the network camera to a power supply using the included power adapter. 2.Wait a moment for the camera to power on. The LED on the back of the camera will flash red to indicate installation mode when it’s ready, and the camera will play a tone from its speaker. 3.
A folder named “Music” will automatically be created when you insert a new microSD card into the network camera. Refer to IV-31. for more information. Now you need to connect your network camera to your network. There are three easy ways: A. With the free EdiView II app on Android or iPhone: II-1. EdiView II App. B. Using a computer and EdiView Finder: II-2. EdiView Finder. C. Using WPS (Wi-Fi Protected Setup), a simple method to connect your camera to your wireless network. Refer to II-4. WPS.
II-1. EdiView II App 1.Use a smartphone or tablet to search, download and install the EdiView II app from Google Play or the Apple App Store. 2.For iOS users, go to your iPhone’s Wi-Fi settings and connect to your network camera’s SSID (EdiView.Setup **), before opening the EdiView II app. Continue to Step 4. 3.Android users ensure your Android device’s Wi-Fi is switched on, and open the EdiView II app. Select your network camera and click “OK” to continue.
4. Android & iOS users select your Wi-Fi network from the list and then enter your Wi-Fi password, before clicking “OK”. If prompted to allow push notifications, please select “Yes”. Click the refresh icon to refresh the Wi-Fi list. 5. Please wait a moment while your camera connects to your Wi-Fi. When you see the “Setup complete” screen, click the “Live” icon to continue or wait for a few seconds to continue automatically.
6.Setup is complete. The camera’s LED should display on and green. You should see a live stream from your network camera which you can view anytime you are connected to the Internet. It is recommended that you change your camera’s password. Go to “More” in the bottom right corner and select “Settings”. You can configure your camera’s settings and functions using the icons below the live image.
II-2. EdiView Finder Ensure your computer is connected to the same router as the network camera using an Ethernet cable. II-2-1. Windows 1. Insert the included CD into your CD-ROM drive and if the setup utility does not automatically open, please locate and open the “Autorun.exe” file in the “Autorun” folder. 2. Click “Setup Utility” to install the EdiView Finder software utility. 3. Click “Next” and follow the on-screen instructions to install the EdiView Finder software utility.
4. When installation is complete, select “Launch EdiView Finder Utility” before clicking “Finish”. Or double click the ”EdiView Finder Utility” icon on your desktop to launch EdiView Finder.
5. EdiView Finder will list all cameras on your local network, along with each camera’s name, model, IP address and MAC address. Click the search icon to refresh the list if your camera is not displayed. The network camera’s IP address is displayed on this screen. After setup, you can enter this IP address into the URL bar of a web browser on the same local network to access your network camera’s web-based configuration interface. 6.
7. Select your wireless network from the list and enter the correct password in the “Password” field, before clicking “OK”. This is the wireless network which your camera will connect to. 8.Unplug the Ethernet cable from your network camera and click “Next”. Please wait a moment for the camera to detect the connection.
9.When the connection is detected as shown below, please click “Next”. 10. Enter a name and password for your camera. The password will be used later to log in to your camera remotely via its cloud ID, web interface or via the EdiView II smartphone app. Click “OK” to continue.
11. The next screen will indicate that setup is complete. The camera is operational and ready for use. Click “OK”or click the URL and a preview window showing a live stream from your camera may open.
II-2-2. Mac EdiView Finder for Mac will not set up your network camera’s wireless connection. After this chapter, please continue to IV-1-2. Wireless to set up the camera’s wireless connection. 1. Insert the included CD into your CD-ROM drive and browse to the “Mac” folder. 2. Copy the “EdiView Finder” file to your desktop and double click the icon to open EdiView Finder. EdiView Finder is also available for download from the Edimax website: http://www.edimax.com/EdiViewFinder.
3.EdiView Finder will list all cameras on your local network, along with each camera’s name, model, IP address and MAC address. Click the search icon to refresh the list if your camera is not displayed. The network camera’s IP address is displayed on this screen. After setup, you can enter this IP address into the URL bar of a web browser on the same local network to access your network camera’s web-based configuration interface. 4.
5. Enter a name and password for your camera. The password will be used later to log in to your camera remotely via its cloud ID, web interface or via the EdiView II smartphone app. Click “Next” to continue. 6. The next screen will indicate that setup is complete. The camera is operational and ready to be configured for a wireless connection. Click “Finish” and a preview window showing a live stream from your camera may open. 7. To setup your network camera’s wireless connection, please follow IV-1-2.
II-2-3. Using EdiView Finder You can also use EdiView Finder to find your network camera’s IP address, view a live stream, or modify the network camera’s IP address.
EdiView Finder will locate your network camera as long as you are on the same local network. Static IP users who may be using a different IP address subnet to the network camera should still be able to locate the network camera with EdiView Finder. If you encounter difficulties, it is recommended that you use a DHCP server – though you can manually set the network camera’s IP address using EdiView Finder (above) or using the web-based configuration interface (see IV-1-1. Network) if you need.
II-3. WPS (Wi-Fi Protected Setup) The WPS (Wi-Fi Protected Setup) button is a quick and easy alternative to establish a secure wireless connection between your network camera and your wireless router/access point. 1. Press and hold the WPS button on your wireless router/access point for the correct length of time to activate its WPS. Please check the instructions for your wireless router/access point for how long you need to hold down its WPS button to activate WPS. 2.
III. Mounting Stand A stand for your network camera is included in the package contents. The stand requires some assembly. The mounting stand is for mounting the network camera to a wall. The camera can stand by itself on a flat surface without the mounting stand. 1. Attach the included mounting stand to a wall using the included screws as shown below: 2.
IV. Web-Based Management Interface When you are using the same local network as your camera, you can use the web-based management interface to view or configure the camera and to use the camera’s functions such as music player and temperature and humidity sensor. You can access the web-based management interface with a web browser on a smartphone or computer.
2. You may be prompted to allow a Java add-on to run. Please click the message where it says “click here” and then click “Run Add-on”. If any other security warnings/prompts appear, please select “Run” or “Allow” or similar, depending on your browser. 3. Enter the username and password for your network camera (default username: admin default password: 1234). The network camera’s webbased management interface will then be displayed in your browser.
4. For computer users, the “Live View” screen will be displayed, as shown below. On the live view screen you can see a live stream from your camera and use the icons on the left side to pan, tilt and take snapshots or recordings. You can also control the network camera’s music player from here and view temperature and humidity information. Environment sensor settings can be configured in System > Environment Sensor. A log of environment sensor data can be found in Status > Environment Sensor Log.
Preset Adjust the camera’s viewing position to any of four preset viewing points. Presets can be configured in Pan & Tilt Preset (refer to IV4-2. Preset) Music Player Playlist Stop Play Random/ Repeat Timer Playlist Click the playlist icon to open the menu: Check the boxes to include songs in the playlist and click “Save’. The playlist can consist of a maximum six songs – including the default song stored in the network camera.
Click the icon to select random, repeat or none. Random will select the next song from the playlist randomly, while repeat will play the next song in the playlist and continue to play the list in a loop.
Timer Set the time for use with “Random” and “Repeat” functions. Select from 0, 5, 15, 30 or 60 minutes to continue playing music for that duration. 5. Select “Setup” at the top center and use the menu down the left side to navigate to the network camera’s various settings. Each menu item is described in the following chapters. 6. After making any changes, click “Save Settings” to save the settings and bring the changes into effect.
IV-1. Basic The “Basic” menu opens a submenu with eight categories of settings for your network camera’s basic operation. Select a category and refer to the appropriate chapter.
IV-1-1. Network Network settings are displayed on this page, as shown below. You can configure your network camera to dynamically receive a local IP address from your router’s DHCP server or you can specify a local static IP address for your network camera. Additionally, advanced users can configure the camera using PPPoE.
Network Type Select “DHCP” to automatically assign an IP address to your network camera from your router or “Static IP” to manually set a static IP address using the fields below. IP Address Static IP users specify an IP address here, which will be the IP address of your network camera. Enter the subnet mask of the IP address. Enter the gateway address of your network. Enter the IP address of your primary DNS server. Enter the IP address of your secondary DNS server (optional).
IV-1-2. Wireless The wireless page allows you to configure settings for your network camera’s wireless connection. For Windows users, your wireless connection should have been set up already using EdiView Finder, though you can still use this page to revise the settings if you need. Mac users need to configure these settings manually since EdiView Finder on Mac will not set up your camera’s wireless connection.
IV-1-2-1. Smartphone 1. Select “Basic” from the menu on the left side and then select “Wireless”. 2.
C A B E D 41
A Wireless Connection Select “Enable” to enable the wireless connection. “Refresh” to display all available Wi-Fi B Available Network (1) Click networks. your Wi-Fi network from the list. This is the C Available Network (2) Select wireless network which your camera will connect to. D E WPA Pre Shared Key Enter your Wi-Fi password. Save Settings Click “Save Settings” to save your settings. 3. After the settings are saved, remove the Ethernet cable from your network camera.
IV-1-2-2. Computer 1. Configure the wireless settings A – E shown in the table below: A B C D E A Wireless Connection Select “Enable” to enable the wireless connection. B Available Network C Connected Click “Refresh” to display all available Wi-Fi networks. Select your Wi-Fi network from the list. This is the wireless network which your camera will connect to. D WPA Pre Shared Key Enter your Wi-Fi password. E Save Settings 2. Click “Save Settings” to save your settings.
IV-1-2-3. WPS WPS (Wi-Fi Protected Setup) is a quick and easy way to set up wireless connections between compatible devices. Use the “Start PBC” or “Start PIN” button to activate WPS on your network camera. Your network camera’s WPS PIN code is also listed next to “Self PinCode”. Self PinCode Access PBC Mode Configure via PinCode Your network camera’s WPS PIN code is listed here. Click “Start PBC” to activate push-button WPS on your network camera.
IV-1-3. Dynamic DNS Dynamic DNS (DDNS) is a service which provides a hostname-to-IP service for dynamic IP users. If your Internet service provider didn’t issue a fixed IP address, you can use a third-party dynamic DNS provider to map your current IP address to a fixed IP address. Several free or paid DDNS services are available online, please use the information provided by your DDNS provider to configure the settings on this page.
IV-1-4. RTSP Real Time Streaming Protocol (RTSP) enables the network camera to be used with a streaming media server. Enter the required RTSP settings. RTSP Port MJPEG RTSP Path H.264 RTSP Path (HD) H.264 RTSP Path (SD) H.264 RTSP Path (Mobile) RTP Port Range Verification Enter the RTSP port. Enter the MJPEG RTSP path. Enter the H.264 High Definition (HD) RTSP path. Enter the H.264 Standard Definition (SD) RTSP path. Enter the H.264 Mobile RTSP path. Enter the RTP port range.
IV-1-5. Date & Time You can set and adjust the network camera’s system time and date on this page. Maintaining a correct system time is particularly important for recorded video organization/playback. Mode Set Time & Date Manually Synchronize to PC time NTP Server Time Zone Daylight Saving Select ”NTP” or “Manual Setting”. NTP (Network Time Protocol) can set and maintain the time and date automatically via an NTP server on the local network, if available.
IV-1-6. Users In addition to the default administrator account, you can configure several different login accounts for the network camera, with two different levels of access – operator and guest. Operator accounts can configure partial functions of the network camera similar to the administrator account, while guest accounts can only view the camera’s image. User List User Name Password Confirm password Existing users are listed here. Select a user here to modify the settings. Input user’s name here.
Authority Add Modify Remove Anonymous Login Select the user’s authority: Operators can view video and configure some settings, while guests can only view video. Add a new user. Save the changes to an existing, selected user. Remove selected user. Enable or disable anonymous login. Anonymous login allows anyone to login to the network camera and view images. This function is useful if you want to setup a remote video server.
IV-1-7. UPnP Universal plug-and-play (UPnP) is a set of networking protocols which enables network devices to communicate and automatically establish working configurations with each other. When enabled, Windows computers can automatically discover the network camera on the local area network. The network camera also supports IGD. Enable/Disable Enable or disable UPnP.
IV-1-8. Bonjour Bonjour is a feature of Mac computers which allows Safari web browser to discover devices and services on the local network and provide a quick shortcut for access. When enabled, Safari users on the local network can find a shortcut to the network camera under Safari’s “Bonjour” menu. Select “Enable” or “Disable”.
IV-2. Video The “Video” menu consists of three categories for configuring the network camera’s video settings. Select an item from the submenu and refer to the appropriate following chapter.
IV-2-1. Video Settings The “Video Settings” page enables you to modify the network camera’s resolution and frame rate settings for different profiles: HD, SD, Small (mobile) & MJPEG. H264 Resolution H264 Maximum Bit Select a H264 video resolution from the dropdown menu. A higher resolution provides more detailed video but requires more bandwidth.
Rate MJPEG Resolution Maximum Frame rate MJPEG Quality Power frequency Rotate Image OSD from the dropdown menu. A higher bit rate provides more detailed video but requires more bandwidth. The bit rate is accurate ±20%. Select a MJPEG video resolution from the dropdown menu. A higher resolution provides more detailed video but requires more bandwidth. Select the maximum video frame rate. A higher frame rate provides smoother video, but also requires more bandwidth.
IV-2-2. Image Appearance The “Image Appearance” page allows you to adjust various parameters relating to the network camera’s image appearance using the sliders shown below. Brightness/ Contrast/ Saturation/ Sharpness/ Reset to default Save value Click and drag the blue lever to change the value according to your preference for each category. Click to reset all settings back to the default value of 50. Save changes.
IV-2-3. Night Vision Night-vision allows your network camera to capture images in dark environments by using infra-red LEDs. Auto-switch will detect light levels in your network camera’s environment and automatically switch to night-vision in low light. Select “Enable” or “Disable” for night-vision auto-switch.
IV-3. Audio The network camera includes an audio feature to play music from a microSD card. Configure the settings using the “Music Settings” page: IV-3-1. Music Settings AEC (Advanced Echo Cancellation) is enabled by default. It is not recommended to disable AEC during two-way communication. When you insert a microSD card into the network camera, a folder named “Music” will automatically be created.
3. Use the checkboxes to select music files and click “Add to Playlist” to add selected files to the playlist. The music files will now be available using the music player in the “Live View” screen: Click the playlist icon to open the menu: Check the boxes to include songs in the playlist and click “Save’. The playlist can consist of a maximum six songs – including the default song stored in the network camera.
AEC Advanced echo cancellation (AEC) is enabled by default to provide better sound quality. If the camera is playing mp3 files, the remote user (e.g. EdiView II app) will not be able to hear the mp3 during two-way communication. If using two-way communication, it is not recommended to disable AEC.
IV-4. Events Select an item from the “Events” menu and refer to the appropriate following chapter. You can configure settings for motion detection, scheduling, SMTP and FTP. IV-4-1. Motion Detection IV-4-1-1. Motion Detection The network camera features a motion detection function and various options for (motion detection) events notification. When motion is detected, it is defined as an “event” and the camera will record for a specified length of time.
Motion Detection Enable or disable the motion detection function of your network camera. Interval Time To After motion is detected, the network camera Detect will not detect motion again for this length of time. For example, using an “Interval Time To Detect” of 20 seconds means that after motion is detected, the camera will not detect any further motion for 20 seconds. Then after 20 seconds, the camera will detect motion again.
IV-4-1-2. Detection Region When using the network camera’s motion detection function, you can specify the area in the video where the network camera should be sensitive to motion. Motion outside of the detection region will be ignored by the network camera. This is useful to avoid false alarms. Region 1 / Region 2 / Region 3 Check the box to enable up to three motion detection regions. A color-coded rectangle will appear on the video view for each enabled region.
Sensitivity Threshold Save Adjust the sensitivity level of motion detection for each region. A higher value will trigger the alarm for minor motion in the video and vice-versa. You can reduce the sensitivity level if you receive unnecessary event notifications. Adjust the motion detection threshold level for each region. A higher value will trigger the alarm for large objects in the video, a lower value will trigger the alarm for smaller objects. Save your settings.
IV-4-1-3. Schedule Settings The network camera’s motion detection function can be scheduled to be active on/at specified times and days. Select “Enable” to enable this feature and then define which times the network camera’s motion detection will be active using the table below. For each day, click and drag across the timeline on the times which you want motion detection to be active. A blue box indicates a scheduled recording.
Delete Delete All Select All Store Delete the selected blue recording block on the timeline. Delete all blue recording blocks on the timeline. Select all blue recording blocks. Store the recording settings on the timeline.
IV-4-2. Sound Detection IV-4-2-1. Sound Detection The network camera features a sound detection function and various options for (sound detection) events notification. When sound is detected, it is defined as an “event” and the camera will record for a specified length of time. You can set the camera to send this recording as a notification via email or FTP, and/or to local storage such as a NAS or microSD card inside the camera.
Sound Detection Enable or disable the sound detection function of your network camera. Interval Time To After sound is detected, the network camera Detect will not detect sound again for this length of time. For example, using an “Interval Time To Detect” of 20 seconds means that after sound is detected, the camera will not detect any further sound for 20 seconds. Then after 20 seconds, the camera will detect sound again.
IV-4-3. Notification IV-4-3-1. Mail Settings Recordings of events (motion or sound detected) can be sent to a designated email recipient. This function must be enabled in “Motion Detection” or “Sound Detection” settings in the “Events” menu. Enter the required information about your sender and recipient email accounts as shown below.
Recipient E-Mail Address Sender E-Mail Address SSL/TLS SMTP Authentication Account Password Send Test Email information can be provided by your email service provider. Enter the email recipient’s email address here. Enter the sender’s email address here to avoid spam filter issues. Select ‘SSL or TLS’ when your SMTP server requires encryption. Consult your mail server administrator when in doubt. Select ‘Enable’ when your SMTP server requires authentication.
IV-4-3-2. FTP Recordings of events (motion or sound detected) can be sent to a designated FTP server. This function must be enabled in “Motion Detection” or “Sound Detection” settings in the “Events” menu. Enter the required information about your FTP server as shown below. FTP Server User Name Password Port Path Passive mode Enter the IP address or host name of the FTP server. Enter the user name required by the FTP server. Enter the password of the FTP server.
IV-4-3-3. Push The network camera can send push notifications to your smartphone if you have the EdiView II app installed. Push notifications can be sent based on motion detection and sound detection events, and also when your camera reconnects to the Internet after a disconnection. Reconnection alerts are sent when the camera actually reconnects to the Internet, not when a disconnection occurs. Push notification Sound alert Enable or disable all push notifications.
IV-5. Storage Settings The “Storage Settings” menu enables you to configure the settings for local storage of motion or sound detection events/recordings. You can also configure scheduled recording. IV-5-1. Storage Directory The network camera can store recordings of motion detection events to local storage: NAS or MicroSD. Select a video profile for the recordings (HD, SD or Small) and select your storage location and click “Save settings”.
IV-5-2. Schedule Settings The network camera can be scheduled to record automatically at/on specified times and days. Select “Enable” to enable this feature and then define at which times the network camera will record using the table below. For each day, click and drag across the timeline on the times which you want to record. A blue box indicates a scheduled recording. In the example below, recording is scheduled for 8am – 6pm Monday to Saturday. By default, the schedule may be full.
IV-5-3. NAS Settings If using a NAS server for local storage, configure the settings on this page according to your NAS. Status NAS IP & Sharing Resource Notification for space full Cycle Recording Max Recording File Time Authentication Displays the status (connected or disconnected) of your network camera and NAS server. Enter the local IP address of your NAS and the path of a shared folder to store your network camera’s recordings.
Username Password IV-5-4. “Anonymous” if no authentication is required. Enter the username if “Account” is selected above. Enter the password if “Account” is selected above. SD Card Settings The “Basic” menu enables you to set the camera’s name and administrator password, as well as switch the LED(s) on/off according to your preference. Unmount your MicroSD card using the “Unmount” button before removing the card from your network camera.
Max Recording File Time Format SD Card Unmount IV-5-5. stop when storage is full. Set the maximum recording time for each file. This applies to scheduled recordings only. For motion or sound detection recording file times, refer to “Events Motion/Sound Detection”. Click to format your MicroSD card. This will erase all data on your MicroSD card. Click to unmount your MicroSD card from the network camera. This is recommended before removing the MicroSD card from the camera.
Back First Page Previous Page Next Page Last Page Select All Select None Delete Go back to the previous page in the file browser. Go back to the first page in the file browser. Go back to the previous page in the file browser. Go to the next page in the file browser. Go to the last page in the file browser. Select all files or folders visible in the file browser. Deselect all selected files or folders. Delete selected files or folders.
IV-6. Pan & Tilt The network camera features pan and tilt capability which can be configured using the “Pan & Tilt” menu. Select a category from the submenu and refer to the appropriate following chapter. IV-6-1. Pan & Tilt Settings Adjust the settings for your network camera’s pan/tilt function according to your preference. You can adjust the pan/tilt speed, distance and autocalibration settings.
Manual Calibration IV-6-2. few minutes. Click here to command the camera to calibrate itself immediately. Preset The network camera can save up to four preset points within its range of motion, which can then be viewed using the 1 – 4 shortcut icons in “Live View”. This function allows you to avoid manually adjusting the camera’s viewing position each time and instead provides a convenient shortcut to the viewing positions which you use the most.
Set Initial Position IV-6-3. to your preference, and then click “Store Position Information” (above) to save the position as a selected preset. Reset the preview window/viewing position back to the network camera’s default position. Home Set the network camera’s default “home” position – select a preset from 1 – 4. You can adjust preset positions in Pan & Tilt > Preset.
IV-7. System The “System” menu consists of three categories, “Basic”, “Advanced” and “Cloud Service”. Select a category and follow the appropriate chapter for more information. IV-7-1. Basic The “Basic” menu enables you to set the camera’s name and administrator password, as well as switch the LED(s) on/off according to your preference. Network Camera Name Administrator Password Confirm Password LED Indication Set the name of the network camera for reference/identification purposes.
IV-7-2. Advanced The “Advanced” page allows you to upgrade the network camera’s firmware, backup or restore the network camera’s settings, and reset or restart the network camera. Please check the Edimax website for the latest firmware for your network camera. Do not switch off or disconnect the device during a firmware upgrade, as this could damage the device. Firmware Filename Upgrade Firmware Backup Settings Restore Settings Restart Click “Browse” to locate the firmware file on your computer.
Reset to default a restart. Restarting will not affect the camera’s current configuration. Select “Keep Network Settings” or “Default Settings” and then click “Reset to Default”. When the camera resets, “Keep Network Settings” will reset all settings but keep the current network settings. The network camera’s IP address will remain the same. “Default Settings” will reset all of the camera’s settings, including network settings, back to the factory default status.
IV-7-3. Cloud Service Edimax Plug & View is a function to allow you to view your network camera remotely via a cloud server (see V. Myedimax.com). You can enable or disable this feature here. IV-7-4. Environment Sensor Your network camera includes an environment sensor which can detect the temperature and humidity level, and trigger email alerts and push notifications when temperature or humidity exceeds or drops below specified levels.
Send An Alert to Email be triggered. Enable or disable email alerts. When enabled, you need to configure email settings in Events > Notification > Mail Settings. Humidity Sensor Send a Notice When When email alerts are enabled (below), Humidity Exceeds specify a humidity level which must be exceeded to trigger an alert. Send a Notice When When email alerts are enabled (below), Humidity is Below specify a humidity level under which alerts will be triggered. Send An Alert to Enable or disable email alerts.
IV-8 Status The “Status” menu provides important information about the status of the network camera. This information is useful for troubleshooting purposes or for network configuration.
IV-8-1. System Information A summary of system-wide information about the network camera is displayed on this page, displayed under four categories: System, LAN, Wireless LAN and IGD (UPnP Port Forward).
IV-8-2. System Log A system log provides information about the network camera’s usage and actions. The system log can also be sent to a remote server for archiving. Log Level Remote Log Remote Log Server Select a level of detail for the log from the dropdown list, from 0 - 4. 0 (minimum) will only log critical information, while 4 (maximum) will log everything. Enable or disable the network camera’s remote log function, to send the log to a remote server for archiving.
IV-8-3. Environment Sensor Log The environment sensor log displays graphical information from the environment sensor every hour for the past 48 hours, and the text log below displays information for the previous 1 year. You can also click “Export Log File” to save the text log as a file on your computer.
V. Myedimax.com You can use your network camera’s Myedimax.com cloud ID to monitor your camera remotely using a web browser from any Internet connection. The network camera’s green power LED must display on to indicate a successful cloud connection, in order for this function to work. 1. Identify your network camera’s cloud ID. The cloud ID is displayed in EdiView Finder (see II-2. EdiView Finder) and on the product label on the back of the network camera (see I-4. Product Label).
If any other security warnings/prompts appear, please select “Run” or “Allow” or similar, depending on your browser. 4. Enter your camera’s password (default password: 1234) and click “OK” to see a live stream from your network camera.
5. The network camera can be operated and configured using the icons in the toolbar located below the image. To configure the network camera, click window: to show the configuration menu 6. Use the slider controls to change the image brightness, saturation, sharpness, video quality and pan & tilt speed. Use the dropdown lists to change the video resolution and operating language, and click “Apply” when finished. Functionality of myedimax.com may vary according to version.
VI. 16 Channel Viewer for Windows The included 16 channel viewing software provides powerful access to your network camera’s functions, along with the capability to view and manage up to 16 network camera simultaneously. VI-1. Installation 1. Insert the included CD into your CD-ROM drive and if the setup utility does not automatically open, please locate and open the “Autorun.exe” file in the “Autorun” folder. 2. Click “16 Channel Viewer” to install the EdiView Finder software utility. 3.
4. Check the installation location and click ‘Next’ to continue. 5. Click “Next” to continue. 6. A summary of your installation will be displayed. Please check everything is correct and click “Install” to begin the installation.
7. Please wait a moment for the installation to complete. 8. Click “Finish” and then double click the “IPCam Surveillance Software” icon on your desktop to open the software.
VI-2. Using the 16 Channel Viewer Your monitor’s resolution must be “1024 x 768” for the 16 channel viewer to work properly. Please set your monitor’s resolution to “1024 x 768”.
Video display area Language Display layout Full screen Scan PTZ control Home Recording A live image of up to 16 connected cameras will be displayed in this area. Select a language from this dropdown menu to change the display language. Change camera image display layout (click a layout icon to change camera display layout). There are 8 kinds of display layouts available. Click this button to switch to full screen mode (only display all camera’s image), press “ESC” key to quit full screen mode.
Message display Close window (stop surveillance) Displays all system messages. Terminates network camera surveillance software. Minimize window Minimizes network camera surveillance software window.
VI-3. Configuring the 16 Channel Viewer VI-3-1. Add Camera/Camera Configuration In order to use the 16 channel viewer software, you must configure/add each camera(s) that you wish to connect. Please click the wrench icon ( ) and a popup menu will appear: Please select “Camera Configuration” to configure/add cameras: Please select “Unblock” if you are prompted by Windows Security Alert that “IPCamViewer” has been blocked, or similar.
VI-3-1-1. Camera In the “Camera Configuration” tab you can add and configure all the cameras you wish to connect to the viewer software. To connect a camera to the viewer software, you need to enter the required information in the “Camera Configuration” box. You can do this automatically by selecting your camera listed in the “Camera Search” box and clicking “Select” (recommended) or you can enter the information manually.
Refresh Name Model IP Address Username Web Port Password Video Format** Reset to connect the selected camera in the “Camera Configuration” box. Refresh the list of cameras on your local network. Enter a reference name for the camera here. The default name is the first 6 characters of the camera’s MAC address. The camera name can be used to easily identify its location for example. Displays the model of the selected camera. Input the IP address of the camera. Input the user name of the camera.
VI-3-1-2. Scheduled Recording You can schedule your network camera(s) to record automatically according to weekly schedules, or unique “one-time” schedules.
Channel Select the channel number you wish to set. One Time Schedules You can specify the one-time schedule for a selected camera; this schedule will be executed once only. New (One Time Schedules) Please specify the time duration of this onetime schedule (the date and time of ‘From’ and ‘To’), then click ‘OK’ to save settings. Edit Delete New (Weekly Schedules) Please note you must set a schedule that will happen in the future, you cannot set a schedule in the past.
Edit Delete start and finish time in the “From” and “To” fields (format HH:MM:SS). The “Continuous Recording” button will set the schedule to record everyday from 12:00:00AM to 11:59:59PM i.e. continuously. You can modify a scheduled recording item. Select a schedule in the ‘One Time Schedules’ list, and click the ‘Edit’ button to edit the start and end time of this schedule. Delete a selected schedule item.
VI-3-1-3. Audio For cameras that support audio, you can use this tab to decide if you wish to hear the audio captured by the selected camera. Channel Mute Audio Record Video Only Select the channel number you wish to set. Check this box and the network camera surveillance software will not play the audio captured by this camera. Check this box and the network camera surveillance software will not record the audio captured by this camera.
VI-3-1-4. Motion Recording The network camera features a motion detection function and various options for (motion detection) events notification. On this page you can enable or disable motion detection and set the camera to send an email or trigger an alarm when motion is detected. Please note that when using the camera for security purposes, it is important to monitor the camera’s stream even when using motion detection. Motion detection may not be 100% accurate.
Send email when motion is triggered Send an email to a pre-defined address when a motion has been detected by the camera.
VI-3-2. General Options Click the wrench icon( ) and a popup menu will appear: When you select “General Options”, please refer to the appropriate following chapter: VI-3-2-1. General All general settings such as the file storage directory and recording spaces can be set here.
Video Storage Settings Scan Time Max Video File Size Cycle Recording Use the “New”, “Edit” and “Delete” buttons to set the directory for local video storage. Available space in the specified directory will be displayed. Define the time period to pause between every camera switch when you activate the ‘Scan’ function. Set the maximum file size of every video file. When the size of the file exceeds this value, the network camera surveillance software will open another file to record the video.
VI-3-2-2. Email Settings If you set your network camera to send email notifications for motion detection events (see VI-3-1-4. Motion Detection), you need to configure your email settings here. E-Mail Subject Recipient E-Mail Address Sender E-Mail Specify the subject of the email notification you will receive. Use the “New”, “Edit” and “Delete” buttons to enter the email address for the recipient(s) of the email notification.
Address SMTP Server SMTP port SMTP Authentication SMTP Account SMTP Password notification email. Specify the IP address or host name of the SMTP server for the sender email. Your ISP can provide this information if you are unsure. Specify the port number of the SMTP server you wish to use here. The default value is 25. Enable or disable SMTP authentication. If you are unsure, check with your ISP. If using SMTP authentication (above), then enter the SMTP account (username) of your SMTP server here.
VI-3-2-3. Security You can set a password to protect the 16 channel viewer software. When enabled, the password will be required each time to open the 16 channel viewer software. To set the password, please use the ‘Security’ tab in the ‘General Options’ menu: Enable Disable When enabled, the password is required to open the 16 channel viewer software. No password is required when disabled.
Password Confirm Password Enter the password you wish to use here. Enter the password you wish to use here again.
VI-3-2-4. About The “About” tab displays the software version number.
VI-4. Changing the Display Layout This network camera surveillance software provides eight display layouts: Each layout displays a different number of cameras in different arrangements. Click the icon which represents your preferred layout and the video display area will change accordingly. Layout style 1: 1 Camera only Displays the video of 1 camera only. Layout style 2: 4 Cameras Displays the video of up to 4 cameras. Layout style 3: 6 Cameras Displays the video of up to 6 cameras.
Layout style 4: 8 Cameras Displays the video of up to 8 cameras. Layout style 5: 9 Cameras Displays the video of up to 9 cameras. Layout style 6: 10 Cameras Displays the video of up to 10 cameras.
Layout style 7: 13 Cameras Displays the video of up to 13 cameras. Layout style 8: 16 Cameras Displays the video of up to 16 cameras.
VI-5. Full Screen Mode Click the ‘Full Screen’ button to switch the display mode to full-screen mode. This uses all available space on your monitor to display the surveillance image. Press the “ESC” key to exit full-screen mode.
VI-6. Scan If you have more than one camera configured, the “Scan” button will switch the display between cameras. “Disconnected” will be displayed in the image window when a configured camera is disconnected. Click the ‘Scan’ button once to activate the scan function (the scan icon will become blue ), click again to stop scanning (the scan icon will become white ).
VI-7. Zoom In/Out For cameras which support the zoom-in/zoom-out function, you can use this function to enlarge or reduce the image size according to your requirements e.g. to see a certain object in greater detail.
VI-8. Pan & Tilt For cameras which support pan & tilt functions, you can adjust the direction the network camera is facing. Please select a camera in the video display area by clicking on its image, and then click the directions you wish the camera to move to (total 8 directions available). Click the ‘Home’ button ( ) to return to the camera’s home (default) position.
VI-9. Snapshot You can take a snapshot of a selected camera and save it to a ‘Snapshot’ subfolder in a pre-defined data directory. Click the snapshot button once to take a snapshot; you can take as many snapshots as you want until the hard disk is full.
VI-10. Recording You can start video recording a selected camera’s image by clicking the ‘Start Recording’ button: When recording starts, you’ll see a message displayed in the message display box, such as ‘1/1 10:00:00, Camera 2 Start Manual’, which means camera 2 started recording manually on 1/1 at 10:00:00. To stop recording, click the ‘Start Recording’ button again, and you’ll see a message displayed in the message display box such as ‘1/1 10:00:00, Camera 2 Stop Manual’.
VI-11. Video Playback You can playback all recorded video by clicking this button. A new window will appear: You have to search the video file before you can play it. There are two kinds of video search: Time Search (search all videos file that fall within a specific period of time) and Motion Search (search all videos recorded by the motion detection function and fall within a specific period of time).
VII. Troubleshooting If you are experiencing problems with your camera, please check below before contacting your dealer of purchase for help. 1. Are there any microSD/SDHC cards recommended for the IC9110W, IC-7113W & IC-3140W? a. Minimum 8GB capacity is recommended with Class 10 speed rating. Below 2GB and above 32GB are not supported.
b. Alternatively you can try formatting your SD card. Be aware that formatting your card removes all existing data, and backup accordingly. 5. My camera image is not clear? a. You can adjust the lens focus for a better image as described in the QIG & user manual. b. Additionally try cleaning the lens with cleaning fabric as it may accumulate dust/fingerprints etc. over time and affect image quality.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1995/95/EC, 2011/65/EC. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 1995/95/CE, 2011/65/CE. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 1995/95/ES, 2011/65/ES.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European R&TTE directive (1999/5/EC, 2006/95/EC) . Equipment: Model No.: 720p Wireless Day & Night PT Network Camera IC-7113W The following European standards for essential requirements have been followed: Spectrum: EMC: EMF: Safety (LVD): ETSI EN 300 328 V1.8.1 (2012-06) EN 301 489-1 V1.9.2 (2011-09); EN 301 489-17 V2.2.
Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code.
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.
Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions.
