IC-9110W V2 User Manual 03-2018 / v1.
Copyright© Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
CONTENTS I Product Information .............................................................................. 5 I-1 I-2 I-3 I-4 I-5 Package Contents .......................................................................................... 5 System Requirements ................................................................................... 6 LED Status ...................................................................................................... 6 Product Label.................................
V-1 V-2 V-3 V-4 V-5 V-6 Basic ............................................................................................................ 57 V-1-1 Network ................................................................................................ 58 V-1-2 Wireless ................................................................................................ 59 V-1-2-1 Smartphone ............................................................................. 60 V-1-2-2 Computer...................
VI-3-1 Add Camera/Camera Configuration ................................................... 107 VI-3-1-1 Camera .................................................................................. 108 VI-3-1-2 Scheduled Recording ............................................................. 110 VI-3-1-3 Audio ..................................................................................... 112 VI-3-1-4 Motion Recording..................................................................
I Product Information I-1 Package Contents Outdoor Image Unit Ethernet Cable Indoor Main Unit Outdoor Image Unit Screws Indoor Main Unit Screws Adhesive Pad Wall Template CD Quick Installation Guide Power Adapter Antenna
I-2 - System Requirements Intel Pentium 4 2.4GHz (above or similar) VGA card (1024*768 or above) CD-ROM Drive At least 128MB hard disk space (256 MB recommended) Windows XP, Vista, 7 or 8/8.1 Web browser (Internet Explorer 7.0, Firefox 3.
I-4 Product Label The product label located on the indoor main unit displays the MAC address, cloud ID and setup SSID of your network camera. The MAC address and cloud ID are the same for easy reference. I-5 Reset If you experience problems with your network camera, you can reset the camera back to its factory default settings. This resets all settings back to default. 1. Press and hold the WPS/Reset button found on the back panel for at least 10 seconds. 2.
3. Wait for the network camera to restart. The camera is ready when the green power LED is flashing slowly. After setup, the green power LED will display on to indicate a successful connection to the cloud server.
II Camera Setup It is recommended that you setup your network camera as shown below and establish a working connection before you install the camera to its outdoor location. Your network camera’s unique SSID is displayed on the product label on the product’s indoor main unit and consits of “EdiView.Setup**” where ** are the last two characters of your camera’s unique MAC address. II-1 Hardware Setup 1. Screw on the included antenna to the product’s indoor main unit. 2.
3. Connect the power adapter to the indoor main unit and to a power supply. 4. Wait a moment for the camera to power on. The green power LED will flash slowly when it’s ready. Now you need to connect your network camera to your network. There are three easy ways: A. With the free EdiLife app on Android or iPhone: Refer to II-2 Connecting to EdiLife App. B. Using a computer and EdiView Finder: II-3 EdiView Finder. C.
After connecting your camera to your network using one of the methods above, you can view your camera’s live image or configure its settings: Local network: A. Using the web based management interface (see V Web-Based Management Interface). B. Using the 16 channel viewer software (see VI 16 Channel Viewer for Windows). Remotely (from any Internet connection): Using the EdiLife app. Follow the instructions in III Outdoor Installation if you need help installing your camera outside.
II-2 Connecting to EdiLife App Follow the instructions below to connect your network camera to your Wi-Fi using the EdiLife smart phone app. Your network camera’s unique SSID is displayed on the product label on the network camera and consists of “EdiView.Setup **” where ** are the last two characters of your camera’s unique MAC address.
II-2-1 Android OS Please make sure the network camera is within the Wi-Fi range of a Wi-Fi router that has internet connectivity. 1. Search and download “EdiLife” in Google Play. 2. Open the EdiLife app and tap the the available wireless device list. 3. Identify and tap the network camera icon to see Your network camera’s unique SSID is displayed on the product label on the network camera and consists of “EdiView.Setup **” where ** are the last two characters of your camera’s unique MAC address.
4. Once connected, the app will prompt you to enter a device name, new password and the password confirmation. Tap icon to continue. 5. The app will display your local Wi-Fi network list. Tap your selection to continue. 6. Enter the Wi-Fi password of the selected network and tap icon to continue.
Please wait patiently for the camera to connect to the selected Wi-Fi network... A Setup complete screen will be displayed on the app when completed. Congratulations! Your camera is up and running! The camera’s green power LED and orange Internet LED should be on. As shown on the left, your camera should be listed on the home screen. Tap your camera to see a live stream. Use the app to view the stream anytime you are connected to the Internet. 7.
II-2-2 Apple iOS Please make sure the network camera is within the Wi-Fi range of a Wi-Fi router that has internet connectivity. 1. On your iOS device, go to Settings. 2. Tap the “Wi-Fi” (outlined in red) option. 3. Find and connect to the network camera by tapping the camera’s Wi-Fi name. Your network camera’s unique SSID is displayed on the product label on the network camera and consists of “EdiView.Setup **” where ** are the last two characters of your camera’s unique MAC address.
5. Open the EdiLife app and tap the 6. Once connected, the app will prompt you to enter a device name, new password and the password confirmation. Tap “OK” to continue. 7. The app will display your local Wi-Fi network list. Tap your selection to continue. icon.
8. Enter the Wi-Fi password of the selected network and tap “OK” icon to continue. Please wait patiently for the camera to connect to the selected Wi-Fi network... A Setup complete screen will be displayed on the app when completed. Congratulations! Your camera is up and running! The camera’s green power LED and orange Internet LED should be on. As shown on the left, your camera should be listed on the home screen. Tap your camera to see a live stream.
Ensure your computer is connected to the same router as the network camera using an Ethernet cable. II-3-1 Windows 1. Insert the included CD into your CD-ROM drive and if the setup utility does not automatically open, please locate and open the “Autorun.exe” file in the “Autorun” folder. 2. Click “Setup Utility” to install the EdiView Finder software utility. 3. Click “Next” and follow the on-screen instructions to install the EdiView Finder software utility.
4. When installation is complete, select “Launch EdiView Finder Utility” before clicking “Finish”. Or double click the ”EdiView Finder Utility” icon on your desktop to launch EdiView Finder. 5. EdiView Finder will list all cameras on your local network, along with each camera’s name, model, IP address and MAC address.
Click the search icon to refresh the list if your camera is not displayed. The network camera’s IP address is displayed on this screen. After setup, you can enter this IP address into the URL bar of a web browser on the same local network to access your network camera’s web-based configuration interface. 6. Double click your camera and then choose “Yes” or “No” if you wish to set up a wireless connection. If you choose “No” please go to step 10.
8. Unplug the Ethernet cable from your network camera and click “Next”. Please wait a moment for the camera to detect the connection. 9. When the connection is detected as shown below, please click “Next”.
10. Enter a name and password for your camera. The password will be used later to log in to your camera remotely via its cloud ID, web interface or via the EdiLife smartphone app. Click “OK” to continue. 11. The next screen will indicate that setup is complete. The camera is operational and ready for use. Click “OK”or click the URL and a preview window showing a live stream from your camera may open.
II-3-2 Mac EdiView Finder for Mac will not set up your network camera’s wireless connection. After this chapter, please continue to IV-1-2. Wireless to set up the camera’s wireless connection. 1. Insert the included CD into your CD-ROM drive and browse to the “Mac” folder. 2. Copy the “EdiView Finder” file to your desktop and double click the icon to open EdiView Finder. EdiView Finder is also available for download from the Edimax website: http://www.edimax.com/EdiViewFinder.htm 3.
The network camera’s IP address is displayed on this screen. After setup, you can enter this IP address into the URL bar of a web browser on the same local network to access your network camera’s web-based configuration interface. 4. Double click your network camera and wait a moment for the network camera to obtain an IP address and test the cloud connection. EdiView should display “Success” as shown below. 5. Enter a name and password for your camera.
6. The next screen will indicate that setup is complete. The camera is operational and ready to be configured for a wireless connection. Click “Finish” and a preview window showing a live stream from your camera may open. 7. To setup your network camera’s wireless connection, please follow V-1-2 Wireless.
II-3-3 Using EdiView Finder You can also use EdiView Finder to find your network camera’s IP address, view a live stream, or modify the network camera’s IP address.
EdiView Finder will locate your network camera as long as you are on the same local network. Static IP users who may be using a different IP address subnet to the network camera should still be able to locate the network camera with EdiView Finder. If you encounter difficulties, it is recommended that you use a DHCP server – though you can manually set the network camera’s IP address using EdiView Finder (above) or using the web-based configuration interface (see V-1-1 Network) if you need.
II-4 WPS (Wi-Fi Protected Setup) The WPS button is a quick and easy alternative to establish a secure wireless connection between your network camera and your wireless router/access point. 1. Press and hold the WPS button on your wireless router/access point for the correct length of time to activate its WPS. Please check the instructions for your wireless router/access point for how long you need to hold down its WPS button to activate WPS. 2.
III Outdoor Installation Recommended installation: The instructions below are a guide – if you are unsure please seek professional assistance. Disconnect the outdoor image unit from the indoor main unit and remove the indoor main unit antenna and power cable before outdoor installation. 1. Establish the best respective locations for the camera’s outdoor and indoor main unit.
3. Drill an additional hole through to the interior of the building wide enough for the outdoor image unit cable.
4. Run the cable attached to the outdoor image unit through the hole from the outside to the interior. 5. Use a sealant to seal the gaps around the cable and screw the outdoor image unit into place. Silicone based sealant is recommended. If your cable hole will not be behind the outdoor image unit, a plastic bushel is also recommended.
6. Use the included screws to screw the outdoor image unit securely into place 7. Adjust the angle of the camera lens on the outdoor image unit to your preference by loosening & tightening the screw. 8. Use the included adherent pad to attach the indoor main unit to your interior wall, or drill holes in your interior wall and use the included screws to screw it firmly into place.
9. Reconnect the antenna and outdoor image unit cable to the indoor main unit. 10. Reconnect the indoor main unit power supply. Use cable clamps (not included) to fix loose cables to the walls according to your preference. 11. You can use an Ethernet cable instead of Wi-Fi to connect the indoor main unit to your router/access point for more stable performance if you prefer.
IV Using the EdiLife App EdiLife is a convenient app that allows you to remotely control your network camera on-the-go. Refer to the following sections on its functions. If you have not already, please go through II-2 Connecting to EdiLife App to connect your network camera to the EdiLife app.
Clicking on the camera will bring you to the camera streaming page. The following sections will explain each options / information outlined in red.
IV-1 Snapshot Tap the icon to take a snapshot. Share Snapshot 1. Upon tapping the icon to take a snapshot, the app will ask whether to share the snapshot. 2. Tapping “SHARE” will bring up the available methods to share the image. Selecting a sharing method will take you to the method’s page that is beyond the scope of this document.
IV-2 Video Settings Tap this icon to adjust the camera stream. The adjustable options are shown on the screen and can be swiped left or right to adjust.
IV-3 Event Tap this icon to display the motion detection events. A maximum of 5 events would be displayed at a time, always replacing the oldest displayed event. Tapping any of the events will play the motion detection video recorded at the time of the event. The video is ~10 seconds long.
IV-4 Connection Information Tap this icon to display current connection information. 1. Connection Methods: P2P, Cloud or LAN. 2. Video Resolution (adjustable, please refer to IV-6 Resolution). 3. Frames Per Second (FPS).
IV-5 Push Notification On / Off Tap this icon to turn “Push Notification” On or Off.
IV-6 Resolution Tap this icon to adjust the resolution of the video stream.
IV-7 Camera Settings Tap this icon for the camera settings page as shown below: From top to bottom: 1. Camera Name: Tap to change camera name 2. ID: Device MAC address 3. Username: Login account name 4. Password: Login password - For another mobile device to access your camera. 5. Flip Image: flip image by 180° 6. Night Vision: Turn on / off night vision mode 7. Motion Detection: Turn on / off motion detection 8. Push Notifications: Tap to go into push notification settings. 9.
IV-7-1 Camera Name Tapping the field will allow you to change the camera’s name as shown on the left: Enter a new name and tap “DONE” (for Android) or the button with similar meaning (for iOS). IV-7-2 Change Password Tapping the field will allow you to change the camera’s password as shown on the left: Enter a new password and tap “DONE” (for Android) or “OK” (for iOS) The password must be over 8 alphanumeric characters. Enter this password in another mobile device to access your camera.
Notification Settings Tap the IV-7-5 Tap the Push Notifications bar to enter push notification settings. 1. Push Notifications: Tap the icon to turn on / off all push notifications. 2. Motion Detection Push Notification: Tap the icon to turn on / off push notifications from motion detection. 3. Reconnected to Internet Push Notification: Tap the icon to turn on / off push notifications from the network camera reconnecting to the Internet. 4. Notification sound: Tap this bar to choose a notification sound.
IV-7-5-1 Date & Time 1. Daylight Savings: Tap the icon to turn on / off daylight savings setting. 2. Date & Time: Displays current date and time. 3. SYNCHRONIZE TO MOBILE DEVICE TIME: Tap this bar to synchronize date and time to your mobile device’s time. Tap icon to refresh current date and time.
IV-7-5-2 Email Account To use email notifications, you need to configure an email address to send and receive the mail. Follow the guide below to configure the email notification settings for different email services: Tap the icon to select the email service (more information in its section below). Select one of Gmail, Yahoo!, Outlook.com, or Manual Settings as your email service.
Gmail, Yahoo! and Outlook email services have pre-configured settings to help facilitate the setup process. We will use Gmail as an example here: 1. Enter the email address in the “Email” space. 2. Enter the password of your email address service in the password space. 3. Send a test email by selecting the “Send a Test Email” option to check if your configuration is operational. Refer to “Send a Test Email” section below if you are unable to send the test email.
Manual Settings If you wish to use other email services, please select “Manual Settings” with further options as shown below: Follow the table below to enter the information required to setup the email service. Where you are unsure about the information below, consult your email service provider. SMTP Server SMTP Port Recipient Email Input the host name or IP address of the SMTP server for the email sender. Input the SMTP port number for the email sender.
Sender Email SSL/TLS SMTP Authentication Account Password Enter the sender’s email address here. When the arrow is selected, options are as shown on the right: Select “SSL” or “TLS” when your SMTP server requires encryption. Enable this option when your SMTP server requires authentication. = Enable; = Disable Input the SMTP account name when your SMTP server requires authentication. Input the password used for SMTP server authentication.
IV-7-5-3 Generate QR code to share Tap the “Generate QR code to share” bar to display a QR code. You can share your device’s information directly using this QR code. Upon entering the QR code page, a warning message will be shown: Tap “OK” to continue displaying the QR code. You can also tap the icon (outlined in red) to save the QR code to your mobile device. Please note, however, that it only lasts 24 hours as said on the warning message.
V Web-Based Management Interface When you are using the same local network as your camera, you can use the web-based management interface to view or configure the camera. You can access the web-based management interface with a web browser on a smartphone or computer. For smartphone users, the appearance of the interface will vary slightly to what is displayed here, though the menu functions described from V-1 Basic onwards are essentially the same. 1.
2. You may be prompted to allow a Java add-on to run. Please click the message where it says “click here” and then click “Run Add-on”. If any other security warnings/prompts appear, please select “Run” or “Allow” or similar, depending on your browser. 3. Enter the username and password for your network camera (default username: admin default password: 1234). The network camera’s web-based management interface will then be displayed in your browser.
4. For computer users, the “Live View” screen will be displayed, as shown below. On the live view screen you can see a live stream from your camera and use the icons on the left side. Snapshot Record Save a snapshot (image) of the network camera’s current view. You will be prompted to select a location to save the image. Record video. You will be prompted to select a location to save the recording. The icon will display blue while recording, click the icon again to stop recording.
5. Select “Setup” at the top center and use the menu down the left side to navigate to the network camera’s various settings. Each menu item is described in the following chapters. 6. After making any changes, click “Save Settings” to save the settings and bring the changes into effect.
V-1 Basic The “Basic” menu opens a submenu with eight categories of settings for your network camera’s basic operation. Select a category and refer to the appropriate chapter.
V-1-1 Network Network settings are displayed on this page, as shown below. You can configure your network camera to dynamically receive a local IP address from your router’s DHCP server or you can specify a local static IP address for your network camera. Additionally, advanced users can configure the camera using PPPoE.
V-1-2 Wireless The wireless page allows you to configure settings for your network camera’s wireless connection. For Windows users, your wireless connection should have been set up already using EdiView Finder, though you can still use this page to revise the settings if you need. Mac users need to configure these settings manually since EdiView Finder on Mac will not set up your camera’s wireless connection.
V-1-2-1 Smartphone 1. Select “Basic” from the menu on the left side and then select “Wireless”. 2.
D E A B C D E 3. Wireless Connection Available Network (1) Available Network (2) WPA Pre Shared Key Save Settings Select “Enable” to enable the wireless connection. Click “Refresh” to display all available Wi-Fi networks. Select your Wi-Fi network from the list. This is the wireless network which your camera will connect to. Enter your Wi-Fi password. Click “Save Settings” to save your settings. After the settings are saved, remove the Ethernet cable from your network camera.
Computer V-1-2-2 1. Configure the wireless settings A – E shown in the table below: A B C D E Wireless Connection Available B Network A C Connected Select “Enable” to enable the wireless connection. Click “Refresh” to display all available Wi-Fi networks. Select your Wi-Fi network from the list. This is the wireless network which your camera will connect to. WPA Pre Enter your Wi-Fi password. Shared Key E Save Settings Click “Save Settings” to save your settings. D 2.
V-1-2-3 WPS WPS (Wi-Fi Protected Setup) is a quick and easy way to set up wireless connections between compatible devices. Use the “Start PBC” or “Start PIN” button to activate WPS on your network camera. Your network camera’s WPS PIN code is also listed next to “Self PinCode”. Self PinCode Access PBC Mode Configure via PinCode Your network camera’s WPS PIN code is listed here. Click “Start PBC” to activate push-button WPS on your network camera.
V-1-3 Dynamic DNS Dynamic DNS (DDNS) is a service which provides a hostname-to-IP service for dynamic IP users. If your Internet service provider didn’t issue a fixed IP address, you can use a third-party dynamic DNS provider to map your current IP address to a fixed IP address. Several free or paid DDNS services are available online, please use the information provided by your DDNS provider to configure the settings on this page.
V-1-4 RTSP Real Time Streaming Protocol (RTSP) enables the network camera to be used with a streaming media server. Enter the required RTSP settings. RTSP Port MJPEG RTSP Path H.264 RTSP Path (HD) H.264 RTSP Path (SD) H.264 RTSP Path (Mobile) RTP Port Range Verification Enter the RTSP port. Enter the MJPEG RTSP path. Enter the H.264 High Definition (HD) RTSP path. Enter the H.264 Standard Definition (SD) RTSP path. Enter the H.264 Mobile RTSP path. Enter the RTP port range.
V-1-5 Date & Time You can set and adjust the network camera’s system time and date on this page. Maintaining a correct system time is particularly important for recorded video organization/playback. Mode Select ”NTP” or “Manual Setting”. NTP (Network Time Protocol) can set and maintain the time and date automatically via an NTP server on the local network, if available.
V-1-6 Users In addition to the default administrator account, you can configure several different login accounts for the network camera, with two different levels of access – operator and guest. Operator accounts can configure partial functions of the network camera similar to the administrator account, while guest accounts can only view the camera’s image. User List User Name Password Confirm password Authority Add Existing users are listed here. Select a user here to modify the settings.
Modify Remove Anonymous Login Save the changes to an existing, selected user. Remove selected user. Enable or disable anonymous login. Anonymous login allows anyone to login to the network camera and view images. This function is useful if you want to setup a remote video server.
V-1-7 UPnP Universal plug-and-play (UPnP) is a set of networking protocols which enables network devices to communicate and automatically establish working configurations with each other. When enabled, Windows computers can automatically discover the network camera on the local area network. The network camera also supports IGD. Enable/Disable Enable or disable UPnP.
V-1-8 Bonjour Bonjour is a feature of Mac computers which allows Safari web browser to discover devices and services on the local network and provide a quick shortcut for access. When enabled, Safari users on the local network can find a shortcut to the network camera under Safari’s “Bonjour” menu. Select “Enable” or “Disable”.
V-2 Video The “Video” menu consists of three categories for configuring the network camera’s video settings. Select an item from the submenu and refer to the appropriate following chapter.
V-2-1 Video Settings The “Video Settings” page enables you to modify the network camera’s resolution and frame rate settings for different profiles: HD, SD, Small (mobile) & MJPEG. H264 Resolution Select a H264 video resolution from the dropdown menu. A higher resolution provides more detailed video but requires more bandwidth. H264 Select a maximum bit rate for H264 videos from the dropdown Maximum Bit menu. A higher bit rate provides more detailed video but Rate requires more bandwidth.
Resolution higher resolution provides more detailed video but requires more bandwidth. Maximum Select the maximum video frame rate. A higher frame rate Frame rate provides smoother video, but also requires more bandwidth. MJPEG Quality Select a quality level for MJPEG videos from the drop down menu. Higher quality requires more bandwidth. Power Adjust the power frequency to 50 Hz or 60 Hz frequency frequency depending on your local region, in order to reduce flicker/improve playback in your videos.
V-2-2 Image Appearance The “Image Appearance” page allows you to adjust various parameters relating to the network camera’s image appearance using the sliders shown below. Brightness/ Contrast/ Saturation/ Sharpness/ Reset to default Save value Click and drag the blue lever to change the value according to your preference for each category. Click to reset all settings back to the default value of 50. Save changes.
V-2-3 Night Vision Night-vision allows your network camera to capture images in dark environments by using infra-red LEDs. Auto-switch will detect light levels in your network camera’s environment and automatically switch to night-vision in low light. Select “Enable” or “Disable” for night-vision auto-switch.
V-3 Events Select an item from the “Events” menu and refer to the appropriate following chapter. You can configure settings for motion detection, scheduling, SMTP and FTP.
V-3-1 V-3-1-1 Motion Detection Motion Detection The network camera features a motion detection function and various options for (motion detection) events notification. When motion is detected, it is defined as an “event” and the camera will record for a specified length of time. You can set the camera to send this recording as a notification via email or FTP, and/or to local storage such as a NAS or MicroSD card inside the camera.
Detection network camera. Interval Time After motion is detected, the network camera will not detect To Detect motion again for this length of time. For example, using an “Interval Time To Detect” of 20 seconds means that after motion is detected, the camera will not detect any further motion for 20 seconds. Then after 20 seconds, the camera will detect motion again. Upload Event A video recording of a detected event can be sent to a File to FTP designated FTP server.
V-3-1-2 Detection Region When using the network camera’s motion detection function, you can specify the area in the video where the network camera should be sensitive to motion. Motion outside of the detection region will be ignored by the network camera. This is useful to avoid false alarms. Region 1 / Region 2 / Region 3 Sensitivity Check the box to enable up to three motion detection regions. A color-coded rectangle will appear on the video view for each enabled region.
Threshold Save Adjust the motion detection threshold level for Day Mode or Night Mode. A higher value will trigger the alarm for large objects in the video; a lower value will trigger the alarm for smaller objects. Save your settings. 1 Day mode and night mode have separate Sensitivity and Threshold settings. 2 All 3 regions use the same Sensitivity and Threshold settings. 3 If Auto Switch of Night Vision is enabled, the light sensor will determine whether to switch to Day mode or IR-based Night Mode.
V-3-1-3 Schedule Settings The network camera’s motion detection function can be scheduled to be active on/at specified times and days. Select “Enable” to enable this feature and then define which times the network camera’s motion detection will be active using the table below. For each day, click and drag across the timeline on the times which you want motion detection to be active. A blue box indicates a scheduled recording.
Delete Delete All Select All Store Delete the selected blue recording block on the timeline. Delete all blue recording blocks on the timeline. Select all blue recording blocks. Store the recording settings on the timeline.
V-3-2 Notification V-3-2-1 Mail Settings Recordings of events (motion or sound detected) can be sent to a designated email recipient. This function must be enabled in “Motion Detection” or “Sound Detection” settings in the “Events” menu. Enter the required information about your sender and recipient email accounts as shown below.
SSL/TLS Select ‘SSL or TLS’ when your SMTP server requires encryption. Consult your mail server administrator when in doubt. SMTP Select ‘Enable’ when your SMTP server requires Authentication authentication. This information can be provided by your email service provider. Account Input the SMTP account name when your SMTP server requires authentication. This information can be provided by your email service provider. Password Input the password used for SMTP server authentication.
V-3-2-2 FTP Recordings of events (motion or sound detected) can be sent to a designated FTP server. This function must be enabled in “Motion Detection” or “Sound Detection” settings in the “Events” menu. Enter the required information about your FTP server as shown below. FTP Server User Name Password Port Enter the IP address or host name of the FTP server. Enter the user name required by the FTP server. Enter the password of the FTP server. Enter the port number of the FTP server.
V-3-2-3 Push The network camera can send push notifications to your smartphone if you have the EdiLife app installed. Push notifications can be sent based on motion detection and sound detection events, and also when your camera reconnects to the Internet after a disconnection. Reconnection alerts are sent when the camera actually reconnects to the Internet, not when a disconnection occurs. Push notification Video/Human motion alert Reconnected to Internet alert Enable or disable push notifications.
V-4 Storage Settings The “Storage Settings” menu enables you to configure the settings for local storage of motion or sound detection events/recordings. You can also configure scheduled recording.
V-4-1 Storage Directory The network camera can store recordings of motion detection events to local storage: NAS or MicroSD. Select a video profile for the recordings (HD, SD or Small) and select your storage location and click “Save settings”. A MicroSD card must be installed in the network camera to use this function. Configure the settings for your NAS or MicroSD card in the V-4-3 NAS Settings or V-4-4SD Card Settings menus respectively.
V-4-2 Schedule Settings The network camera can be scheduled to record automatically at/on specified times and days. Select “Enable” to enable this feature and then define at which times the network camera will record using the table below. For each day, click and drag across the timeline on the times which you want to record. A blue box indicates a scheduled recording. In the example below, recording is scheduled for 8am – 6pm Monday to Saturday. By default, the schedule may be full.
V-4-3 NAS Settings If using a NAS server for local storage, configure the settings on this page according to your NAS. Status Displays the status (connected or disconnected) of your network camera and NAS server. NAS IP & Sharing Enter the local IP address of your NAS and the path of a Resource shared folder to store your network camera’s recordings. Notification for Enable or disable email notifications when your storage space full space is full. Cycle Recording Enable or disable cycle recording.
V-4-4 SD Card Settings The “Basic” menu enables you to set the camera’s name and administrator password, as well as switch the LED(s) on/off according to your preference. Unmount your MicroSD card using the “Unmount” button before removing the card from your network camera. Status Available Space Notify when space is not enough Cycle Recording Displays the MicroSD card status of your network camera: available or unavailable. Displays the available space on the MicroSD card in your network camera.
V-4-5 File Management The file management tool enables you to browse, download and delete recording files on your MicroSD card. Files are grouped according to the following categories: Event: Recordings or images from motion detection events are displayed here. Schedule: Recordings from scheduled recording are displayed here. Manual: Manual recordings are displayed here. Select Event, Schedule or Manual and use the file browser to navigate.
V-5 System The “System” menu consists of three categories, “Basic”, “Advanced” and “Cloud Service”. Select a category and follow the appropriate chapter for more information.
V-5-1 Basic The “Basic” menu enables you to set the camera’s name and administrator password, as well as switch the LED(s) on/off according to your preference. Network Set the name of the network camera for Camera Name reference/identification purposes. This is especially useful when managing multiple network cameras. Administrator Enter your desired administrator password here. This is the Password password used to log into the camera with the “admin” account. The default password is 1234.
V-5-2 Advanced The “Advanced” page allows you to upgrade the network camera’s firmware, backup or restore the network camera’s settings, and reset or restart the network camera. Please check the Edimax website for the latest firmware for your network camera. Do not switch off or disconnect the device during a firmware upgrade, as this could damage the device. Firmware Filename Upgrade Firmware Backup Settings Restore Settings Restart Reset to Click “Browse” to locate the firmware file on your computer.
default click “Reset to Default”. When the camera resets, “Keep Network Settings” will reset all settings but keep the current network settings. The network camera’s IP address will remain the same. “Default Settings” will reset all of the camera’s settings, including network settings, back to the factory default status.
V-6 Status The “Status” menu provides important information about the status of the network camera. This information is useful for troubleshooting purposes or for network configuration.
V-6-1 System Information A summary of system-wide information about the network camera is displayed on this page, displayed under four categories: System, LAN, Wireless LAN and IGD (UPnP Port Forward).
A system log provides information about the network camera’s usage and actions. The system log can also be sent to a remote server for archiving. Log Level Select a level of detail for the log from the dropdown list, from 0 - 4. 0 (minimum) will only log critical information, while 4 (maximum) will log everything. Remote Log Enable or disable the network camera’s remote log function, to send the log to a remote server for archiving. The network camera supports syslog log servers.
VI 16 Channel Viewer for Windows The included 16 channel viewing software provides powerful access to your network camera’s functions, along with the capability to view and manage up to 16 network camera simultaneously. VI-1 Installation 1. Insert the included CD into your CD-ROM drive and if the setup utility does not automatically open, please locate and open the “Autorun.exe” file in the “Autorun” folder. 2. Click “16 Channel Viewer” to install the EdiView Finder software utility. 3.
4. Check the installation location and click ‘Next’ to continue. 5. Click “Next” to continue.
6. A summary of your installation will be displayed. Please check everything is correct and click “Install” to begin the installation. 7. Please wait a moment for the installation to complete.
8. Click “Finish” and then double click the “IPCam Surveillance Software” icon on your desktop to open the software.
VI-2 Using the 16 Channel Viewer Your monitor’s resolution must be “1024 x 768” for the 16 channel viewer to work properly. Please set your monitor’s resolution to “1024 x 768”.
PTZ control Home Recording software will switch through the images of all connected camera automatically. Click this button once to activate the scan function (scan icon will become blue ), click again to stop scanning (scan icon will become white ). There are 8 directions in the Pan Tilt Zoom (PTZ) control ring. If the camera you connect to supports PTZ, you can use the PTZ control ring to change the direction that the camera faces. This function is only available for supported cameras.
VI-3 VI-3-1 Configuring the 16 Channel Viewer Add Camera/Camera Configuration In order to use the 16 channel viewer software, you must configure/add each camera(s) that you wish to connect. Please click the wrench icon ( ) and a popup menu will appear: Please select “Camera Configuration” to configure/add cameras: Please select “Unblock” if you are prompted by Windows Security Alert that “IPCamViewer” has been blocked, or similar.
VI-3-1-1 Camera In the “Camera Configuration” tab you can add and configure all the cameras you wish to connect to the viewer software. To connect a camera to the viewer software, you need to enter the required information in the “Camera Configuration” box. You can do this automatically by selecting your camera listed in the “Camera Search” box and clicking “Select” (recommended) or you can enter the information manually.
Refresh Name Model IP Address Username Web Port Password Video Format** Reset Refresh the list of cameras on your local network. Enter a reference name for the camera here. The default name is the first 6 characters of the camera’s MAC address. The camera name can be used to easily identify its location for example. Displays the model of the selected camera. Input the IP address of the camera. Input the user name of the camera. Input the web port of the camera. The default value is“80”.
VI-3-1-2 Scheduled Recording You can schedule your network camera(s) to record automatically according to weekly schedules, or unique “one-time” schedules. Channel One Time Schedules New (One Time Schedules) Select the channel number you wish to set. You can specify the one-time schedule for a selected camera; this schedule will be executed once only. Please specify the time duration of this one-time schedule (the date and time of ‘From’ and ‘To’), then click ‘OK’ to save settings.
Edit Delete New (Weekly Schedules) Edit Delete You can modify a scheduled recording item. Select a schedule in ‘One Time Schedules’ list, and click the ‘Edit’ button to edit the start and end time of this schedule. Delete a selected schedule item. You can define a weekly recording schedule for specified times and days. Check the days to include in the schedule, and set the daily start and finish time in the “From” and “To” fields (format HH:MM:SS).
VI-3-1-3 Audio For cameras that support audio, you can use this tab to decide if you wish to hear the audio captured by the selected camera. Channel Select the channel number you wish to set. Mute Audio Check this box and the network camera surveillance software will not play the audio captured by this camera. Record Video Check this box and the network camera surveillance software Only will not record the audio captured by this camera.
Motion Recording VI-3-1-4 The network camera features a motion detection function and various options for (motion detection) events notification. On this page you can enable or disable motion detection and set the camera to send an email or trigger an alarm when motion is detected. Please note that when using the camera for security purposes, it is important to monitor the camera’s stream even when using motion detection. Motion detection may not be 100% accurate.
VI-3-2 General Options Click the wrench icon ( ) and a popup menu will appear: When you select “General Options”, please refer to the appropriate following chapter: VI-3-2-1 General All general settings such as the file storage directory and recording spaces can be set here.
Video Storage Use the “New”, “Edit” and “Delete” buttons to set the Settings directory for local video storage. Available space in the specified directory will be displayed. Scan Time Define the time period to pause between every camera switch when you activate the ‘Scan’ function. Max Video Set the maximum file size of every video file. When the size of File Size the file exceeds this value, the network camera surveillance software will open another file to record the video.
VI-3-2-2 Email Settings If you set your network camera to send email notifications for motion detection events (see V-3-1 Motion Detection), you need to configure your email settings here. E-Mail Subject Recipient E-Mail Address Sender E-Mail Address SMTP Server Specify the subject of the email notification you will receive. Use the “New”, “Edit” and “Delete” buttons to enter the email address for the recipient(s) of the email notification.
SMTP port Specify the port number of the SMTP server you wish to use here. The default value is 25. SMTP Enable or disable SMTP authentication. If you are unsure, Authentication check with your ISP. SMTP Account If using SMTP authentication (above), then enter the SMTP account (username) of your SMTP server here. In most cases, it’s the same as your POP3 username (the one you use to receive email). Contact your ISP if you are unsure. SMTP Password Enter the SMTP password of your SMTP server here.
VI-3-2-3 Security You can set a password to protect the 16 channel viewer software. When enabled, the password will be required each time to open the 16 channel viewer software. To set the password, please use the ‘Security’ tab in the ‘General Options’ menu: Enable Disable Password Confirm Password When enabled, the password is required to open the 16 channel viewer software. No password is required when disabled. Enter the password you wish to use here. Enter the password you wish to use here again.
When you open the 16 channel viewer software, you will be prompted to enter the password:
VI-3-2-4 About The “About” tab displays the software version number.
VI-4 Changing the Display Layout This network camera surveillance software provides eight display layouts: Each layout displays a different number of cameras in different arrangements. Click the icon which represents your preferred layout and the video display area will change accordingly. Layout style 1: 1 Camera only Displays the video of 1 camera only. Layout style 2: 4 Cameras Displays the video of up to 4 cameras. Layout style 3: 6 Displays the video of up to 6 cameras.
Cameras Layout style 4: 8 Cameras Displays the video of up to 8 cameras. Layout style 5: 9 Cameras Displays the video of up to 9 cameras. Layout style 6: 10 Cameras Displays the video of up to 10 cameras. Layout style 7: 13 Cameras Displays the video of up to 13 cameras.
Layout style 8: 16 Cameras Displays the video of up to 16 cameras.
VI-5 Full Screen Mode Click the ‘Full Screen’ button to switch the display mode to full-screen mode. This uses all available space on your monitor to display the surveillance image. Press the “ESC” key to exit full-screen mode.
VI-6 Scan If you have more than one camera configured, the “Scan” button will switch the display between cameras. “Disconnected” will be displayed in the image window when a configured camera is disconnected. Click the ‘Scan’ button once to activate the scan function (the scan icon will become blue ), click again to stop scanning (the scan icon will become white ).
VI-7 Zoom In/Out For cameras which support the zoom-in/zoom-out function, you can use this function to enlarge or reduce the image size according to your requirements e.g. to see a certain object in greater detail.
VI-8 Pan & Tilt For cameras which support pan & tilt functions, you can adjust the direction the network camera is facing. Please select a camera in the video display area by clicking on its image, and then click the directions you wish the camera to move to (total 8 directions available). Click the ‘Home’ button ( ) to return to the camera’s home (default) position.
VI-9 Snapshot You can take a snapshot of a selected camera and save it to a ‘Snapshot’ sub-folder in a pre-defined data directory. Click the snapshot button once to take a snapshot; you can take as many snapshots as you want until the hard disk is full.
VI-10 Recording You can start video recording a selected camera’s image by clicking the ‘Start Recording’ button: When recording starts, you’ll see a message displayed in the message display box, such as ‘1/1 10:00:00, Camera 2 Start Manual’, which means camera 2 started recording manually on 1/1 at 10:00:00. To stop recording, click the ‘Start Recording’ button again, and you’ll see a message displayed in the message display box such as ‘1/1 10:00:00, Camera 2 Stop Manual’.
VI-11 Video Playback You can playback all recorded video by clicking this button. A new window will appear: You have to search the video file before you can play it. There are two kinds of video search: Time Search (search all videos file that fall within a specific period of time) and Motion Search (search all videos recorded by the motion detection function and fall within a specific period of time).
VII Troubleshooting If you are experiencing problems with your camera, please check below before contacting your dealer of purchase for help. 1. Are there any microSD/SDHC cards recommended for the IC-9110W V2, IC-7113W & IC-3140W? a. Minimum 8GB capacity is recommended with Class 10 speed rating. Below 2GB and above 32GB are not supported.
4. My camera stopped recording to my microSD/SDHC card. a. Go to ‘SD Card Settings’ in the camera’s user interface: 1. Ensure there is enough space on your microSD/SDHC card. 2. Try using “cycle recording” to periodically overwrite old recordings. b. Alternatively you can try formatting your SD card. Be aware that formatting your card removes all existing data, and backup accordingly. 5. My camera image is not clear? a. You can adjust the lens focus for a better image as described in the QIG & user manual.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC, 2006/95/EC, 2009/125/EC. French: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2004/108/EC, 2006/95/EC, 2009/125/EC Czechian: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 2004/108/EC, 2006/95/EC, 2009/125/EC.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European R&TTE directive (1999/5/EC, 2006/95/EC) Equipment: Internet Camera Model No.: IC-9110W V2 The following European standards for essential requirements have been followed: Spectrum EMC : ETSI EN 300 328 V1.8.1 (2012-06); : EN 301 489-1 V1.9.2 (2011-09) EMF Safety(LVD) EN 301 489-17 V2.2.
Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does. 1.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License.
NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM ‘“AS IS’“ WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.
