IGS-5208/ IGS-5408P/ IGS-5416P Quick Installation Guide 02-2019 / V1.
Product Information I-1. Overview The Edimax Pro IGS-5208, IGS-5408P and IGS-5416P industrial Gigabit web managed switch come with 8 PoE+ ports (IGS-5408P and IGS-5416P only) and 2 or 4 SFP slots for high-speed Gigabit, long-range copper or optical connections and for enduring, reliable, flexible industrial network deployment.
I-3. Hardware Overview 1. Dimension IGS-5208: 145 mm (H) x 72.20 mm (W) x 113 mm (D) IGS-5408P: 145 mm (H) x 72.
IGS-5416P: 145 mm (H) x 90.80 mm (W) x 113 mm (D) 2. DIN-Rail mount The DIN-Rail clip is already attached on the rear side of the switch supports EN 50022 standard DIN Rail, in the following diagram includes the dimension of EN 50022 DIN Rail. Follow the steps below to mount the switch on the DIN-Rail track. 1. 2. 3. 4. Insert the upper end of the DIN-Rail clip into the back of the DIN-Rail track from its upper side Lightly push the bottom of the DIN-Rail clip into the track.
3. Wall mount Screw the wall-mount brackets with screws in the accessory kit 4. Wiring Power Inputs 1. 2. Insert the positive and negative wires into the PWR1 (+,-) and PWR2 (+,-) on the 4-contact terminal block connector. Tighten the screws to prevent the wires from loosening. 5. Wiring Fault Alarm 1. 2. 3. 4. Insert the wires into the left two contacts of the 4-contact terminal block (Fault Alarm Relay). Tighten the screws to prevent the wires from loosening.
8. Double-Secure Power Input Fault Alarm The power inputs are designed as a "common negative", which implies that the negative input is connected, but "double-secure" is supported to prevent the un-notified failure of power from one of the negative inputs. If one of the negative power input fails, the system will detect it and the system will trigger the event if the users set the fault alarm or event log for powers. 9.
IGS-5208 LED SFP Slot P9 to P10 (1000M) LAN Port P1 to P8 (1000M) LAN Port P1 to P8 (10/100M) Color Green Green Green Status Description On The 1000Mbps link of the fiber port is active. Flickering Data is transmitted on the fiber port at 1000Mbps. Off The 1000Mbps link of the fiber port is inactive. On The 1000Mbps link of the port is active. Flickering Data is transmitted on the port at 1000Mbps. Off The 1000Mbps link of the port is inactive.
I-5. Login To login to the web management interface and configure the switch’s settings, connect a computer to the switch using an Ethernet cable. Open a web browser and go to the switch’s IP address. The default IP address is 192.168.2.1. Your computer’s IP address must be in the same subnet as the switch. For the default IP address this is any IP address in the range 192.168.2.x (x = 2 – 254). You can modify the IP address of your computer if you need. Default IP address 192.168.2.
COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/30/EU. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2014/30/EU. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 2014/30/EU. Polski: Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami określonymi Dyrektywą UE 2014/30/EU.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European R&TTE directives. Equipment: Industrial Ethernet Switch Model No.: IGS-5208/IGS-5408P/IGS-5416P The following European standards for essential requirements have been followed: Directives 2014/30/EU EMC : EN 55032:2012 / AC: 2013 CISPR 32: 2012 EN 61000-3-2:2014 EN 61000-3-3:2013 EN 55024:2010 + A1: 2015 Edimax Technology Europe B.
Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
