User Manual
Table Of Contents
- Intended Readers
- Icons for Note, Caution, and Warning
- I. Product Overview
- I-1 . Product Brief Description
- I-2. Product Specification
- I-3. Hardware Description
- I-4. DIN-Rail Mounting
- /I-5. Console Connection
- The Console port is for local management by using a terminal emulator or a computer with terminal emulation software.
- DB9 connector connect to computer COM port
- Baud rate: 115200bps
- 8 data bits, 1 stop bit
- None Priority
- None flow control
- I-6. Connecting Cable
- II. Preparing for Management
- III. Web Management
- III-1. Web Management - Overview
- III-2. Web Management – Basic Settings
- III-3. Web Management – Redundancy
- III-4. Web Management – Management
- III-5. Web Management – L2 Switching
- III-6. Web Management – Security
- III-7. Web Management – Diagnostics
- III-8. Web Management – Monitoring
- III-9. Web Management – MAC Table
- III-10. Web Management – Maintenance
- Appendix A: IP Configuration for Your PC
- Appendix B: CLI Command Reference
- Revision History
- Federal Communication Commission Interference Statement
- R&TTE Compliance Statement
117
ERPS GROUP
Command
Explanation
Mode
ethernet redundancy erps-ring [ 1 | 2 | 3 ]
Ethernet Ring Protection Switching(ERPS) mode
Configure
aps-channel [1 - 4094]
Set APS channel
ERPS
disable
Disable ERPS function
ERPS
enable
Enable ERPS function
ERPS
erps-ring [ 1 | 2 | 3 ]
Change to Other ERPS Ring
ERPS
ext-command clear
Extended ERPS command - Clear
ERPS
ext-command fs
Extended ERPS command– Forced Switch
ERPS
ext-command ms
Extended ERPS command– Manual Switch
ERPS
id [1 - 239]
Set Ring ID
ERPS
mel [0 - 7]
ERPS mel
ERPS
revertive
Set as revertive mode
ERPS
ring-port 0 [1(lan1) - N(lanN)]
Mapping ERPS ring port0 to switch port
ERPS
ring-port 1 [1(lan1) - N(lanN)]
Mapping ERPS ring port1 to switch port
ERPS
role port0 [o(owner) | n(neigh) | i(interconn)]
Set role on ring port0
ERPS
role port1 [o(owner) | n(neigh) | i(interconn)]
Set role on ring port1
ERPS
timer guard [10 - 2000]
Set guard timer interval
ERPS
timerhold-off [0 - 10000]
Set hold-off timer interval
ERPS
timer wtr [1 - 12]
Set WTR timer interval
ERPS
type [m(major-ring) | s(sub-ring)]
Set type as Major-Ring or Sub-Ring
ERPS
virtaul-channel major-ring channel-id [1-4094]
Set virtual channel for ERPS Ring
ERPS
virtaul-channel sub-ring set
Set virtual channel for ERPS Sub-ring
ERPS
show config
Displays ERPS configuration
ERPS
show port status
Displays ERPS ring port status
ERPS
show status
Displays ERPS status
ERPS
no aps-channel
Default ERPS aps-channel
ERPS
no id
Default Ring ID as default
ERPS
no revertive
Default mode non-revertive
ERPS
no ring-port 0
Default ring port0 as lan1
ERPS
no ring-port 1
Default ring port1 as lan2
ERPS
no role port0
Default role of ring port0 as none
ERPS
no role port1
Default role of ring port1 as none
ERPS
no timer guard
Default guard timer
ERPS
no timerhold-off
Default hold-off timer
ERPS
no timer wtr
Default wtr timer
ERPS
no type
Default ring type as Major-Ring
ERPS
no virtaul-channel major-ring channel-id
Default virtual channel as ERPS Major Ring's
aps-channell
ERPS
no virtaul-channel sub-ring set
Default virtual channel for ERPS Sub-ring as
None
ERPS