Office +1 OAP1300 Guida di installazione rapida 11-2020 / v1.
I Breve riepilogo e promemoria 1. Puoi trovare tutti i documenti, i video e i programmi di riferimento: www.edimax.com/edimax_pro/download/Office1-2-3 2. Per un'introduzione completa al sistema Office 1-2-3, consulta il seguente link: http://office123.edimax.com 3. Può esserci solo un'unità master Office 1-2-3 nella rete. sono Office +1. 4. Durante l'avvio iniziale, l'AP master comunicherà automaticamente le sue impostazioni a tutti i punti di accesso Office +1 (in circa 10 minuti). 5.
II Informazioni sul prodotto II-1 Contenuti della confezione 1 2 3 4 5 6 7 8 1. Punto di accesso OAP1300 2. Esempio di fissaggio a muro con viti 3. Set viti per fissaggio a muro 4. CD 2 5. Guida di installazione rapida 6. Cavo Ethernet 7. Cinghie per montaggio su palo x2 8.
II-2 Requisiti di sistema - Modem e router cavo/DSL esistente - Computer con browser web per la configurazione del punto di accesso II-3 Panoramica Hardware Porte e pulsanti C A B C LAN 1 POE-IN LAN 2 POE-OUT Reset B A Porta LAN con INGRESSO Power over Ethernet (PoE) Porta LAN con PoE OUT Tasto Reset 3
II-4 LED di stato LED LED di stato Acceso 5G (WLAN) Spento Acceso 2,4G (WLAN) Spento Acceso LAN (PSE) Lampeggiante Spento Acceso LAN (PD) Lampeggiante Spento Acceso Stato Spento Acceso Alimentazione Lampeggiante Spento Descrizione Wireless attivato. Wireless disattivato. Wireless attivato. Wireless disattivato. Porta LAN connessa. Attività (trasmissione e ricezione). Porta LAN non connessa. Porta LAN connessa. Attività (trasmissione e ricezione). Porta LAN non connessa.
II-5 Reset Se si riscontrano problemi con il punto di accesso, è possibile ripristinarlo alle impostazioni predefinite alla fabbrica. Questa operazione ripristina tutte le impostazioni a quelle predefinite. 1. Premere e tenere premuto il tasto reset sul punto di accesso per almeno 10 secondi, quindi rilasciare il tasto. Potrebbe essere necessario utilizzare uno spillo o un oggetto appuntito simile per premere il tasto reset. 2. Attendere il riavvio del punto di accesso.
III Aggiunta di AP Office +1 a Office 1-2-3 La guida di impostazione rapida permette di aggiungere l'AP Office +1 alla rete Wi-Fi Office 1-2-3 a elevata velocità esistente. 1. Identificare lo switch PoE connesso alla rete Office 1-2-3 esistente. 2. Collegare l'AP Office +1 allo switch PoE utilizzando un cavo Ethernet. Assicurarsi che il cavo Ethernet sia collegato alla porta PoE del punto di accesso, come mostrato di seguito: 3.
IV Sostituzione dell'AP master NOTA: è possibile avere un SOLO AP master all'interno della rete. Seguire questa procedura solo se è necessario sostituire l'AP master. In questa sezione è contenuta una guida passo-passo alla sostituzione dell'AP master originale che vi aiuterà a effettuare l'upgrade del firmware AP master e a recuperare le impostazioni di sistema precedentemente salvate.
2. Localizzare l'AP Office +1 cliccando su "Scopri" 3. Fare clic sull'indirizzo IP del punto di accesso che diventerà l'AP master e accedere all'interfaccia utente web. 8 nell'IP Finder.
Dopo aver effettuato l'accesso alla pagina web, dovreste essere invitati a inserire username e password, inseriteli (username di default: admin, password: 1234) per procedere: L'interfaccia utente web è mostrata di seguito: 9
4. Fare clic sull'icona "Impostazioni di sistema". Upgrade del firmware 5. Scorrere lungo la pagina fino a trovare la dicitura "Upgrade del firmware". Se non l'avete già fatto, vi invitiamo a visitare il link URL di seguito per scaricare il firmware più recente: www.edimax.com/edimax_pro/download/Office1-2-3 Localizzare il firmware master e fare clic sull'icona di download per scaricarlo. 6. Fare clic su "Scegli File" per selezionare il file firmware master. 7.
Verrà mostrato un messaggio di notifica, fare clic su "OK" per continuare. Il sistema verrà aggiornato, si prega di attendere... 8. Dopo aver effettuato l'upgrade del firmware, il sistema vi inviterà a inserire username e password, inseriteli (username di default: admin, password: 1234) per procedere: 9.
Verrà mostrato un messaggio di sistema, fare clic su "OK" per continuare Il sistema verrà riavviato, si prega di attendere... 10.
11. Fare clic sull'icona "Impostazioni di sistema". Rispristino alle impostazioni precedenti 12. Scorrere fino a individuare la dicitura "Upgrade del firmware". 13. Fare clic sul pulsante "Scegli file" per trovare le impostazioni precedentemente salvate sul vostro computer. 14. Fare clic su "Ripristina" per sostituire le impostazioni correnti.
V Installazione hardware A processo di installazione completato, sarà possibile riposizionare il punto di accesso nella posizione desiderata. V-1 Antenna Le antenne devono essere fissate al punto di accesso.
V-2 1. Accendere il punto di accesso esterno Rimuovere la copertura dalla parte inferiore del punto di accesso 1) tirando i ganci verso l'alto e 2) tirando la copertura verso il basso, come mostrato di seguito: Copertura inferiore 2. Collegare un cavo Ethernet alla porta LAN 1 (PoE-In) del punto di accesso e lo switch PoE per avviare il punto di accesso. Porta LAN 1 (PoE-In) 3. Il punto di accesso verrà alimentato dallo switch PoE. Collegare un altro cavo Ethernet alla LAN 2, se necessario. 4.
5. Fissare il gancio con il punto di accesso attendendo il clic e assicurarsi che non fuoriesca facilmente. La copertura funziona come dispositivo antipioggia idoneo per l'uso all'aperto.
V-3 Montaggio Dopo aver avviato il punto di accesso, montarlo secondo le opzioni desiderate: Montaggio a parte o su palo Montaggio a parete Fissare il punto di accesso e il supporto alla parete usando i modelli di montaggio forniti e il set di viti per il montaggio a parete.
Montaggio su palo Fissare il supporto e il punto di accesso sul palo mediante le cinghie per fissaggio su palo in dotazione.
Professional installation warning: This device is point-to-multi-point device. The general user should not attempt to install or change settings, it needs to be installed by a qualified personal who has RF exposure and related rule knowledge or technology. The installation position and output power does not exceed the limit set forth in US Rule CFR 47 part 15 section 15.247 & 15.407. If violate the rule, could lead to serious federal penalty. It is complies with §15.
COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU, 2014/35/EU. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2014/53/EU, 2014/35/EU. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 2014/53/EU, 2014/35/EU.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European Radio Equipment directives. Equipment: AC1300 Outdoor AP Model No.: Office +1 OAP1300 The following European standards for essential requirements have been followed: Directives 2014/53/EU Spectrum EMF : EN 300 328 V2.1.1 (2016-11) EN 301 893 V2.1.1 (2017-05) : EN 301 489-1 V2.1.1 (02-2017) Draft EN 301 489-17 V3.2.
Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code.
intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2.
Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions.