PrimeAX 1-2-3 & PrimeAX +1 Rychlá instalační příručka 06-2021 / v1.
Obsah I. Informace o produktu ................................................1 I-1. Obsah balení.................................................................................... 2 I-2. Systémové požadavky ....................................................................... 3 I-3. Přehled hardwaru ............................................................................. 4 I-4. Stav LED ........................................................................................... 5 II.
I. Informace o produktu PrimeAX 1-2-3 s předkonfigurovanými přístupovými body Master a Slave, je jednoduchý, bezpečný, kompletní a rozšiřitelný systém Wi-Fi s technologií Wi-Fi 6 poskytující bezdrátové rychlosti až 1800Mbps.
I-1.
PrimeAX +1: PrimeAX +1 PrimeAX 1-2-3 (Slave) Rychlá instalační příručka I-2.
I-3.
I-4. Číslo Popis 1 Ethernetový port (PoE) 2 Napájecíport (12V/1.
II. Instalace hardwaru Při instalaci PrimeAX 1-2-3 postupujte podle pokynů níže. Router nebo přepínač: Připojte přístupový bod k routeru nebo přepínači PoE pomocí ethernetového kabelu.
II-1. Připojení přístupového bodu k routeru Pokud používáte router, připojte napájecí adaptér k přístupovému bodu a zásuvky. Chvíli počkejte, než se přístupový bod spustí. Zařízení je připraveno, když se LED změní na modrou.
II-2. Připojení přístupového bodu k přepínači PoE Pokud používáte přepínač PoE, ujistěte se, že je kabel Ethernet připojen k portu Ethernet na přepínači PoE. Přístupový bod bude napájen přepínačem. Chvíli počkejte, než se přístupový bod spustí. Zařízení je připraveno, když se LED změní na modrou. Pokud používáte přepínač PoE, nepoužívejte napájecí adaptér. POZNÁ MKA: Vezměte prosím na vědomí, že PrimeAX (Mater & Slave) je předkonfigurovaný, dokončete instalaci hardwaru podle výše uvedených kroků.
II-3. Přidání dalšího PrimeAX +1(Slave) Jednoduše zapojte ethernetový kabel do ethernetového portu PrimeAX (Slave). PrimeAX (Master) automaticky detekuje PrimeAX (Slave). Zařízení budou spárována. III. Rychlé nastavení Průvodce nastavením vám pomůže nakonfigurovat PrimeAX 1-2-3 a jeho základnínastavení. Podle níže uvedených pokynů se přihlaste na konfigurační stránku PrimeAX 1-2-3. 1. Otevřete prohlížeč a do adresního řádku zadejte výchozí IP adresu přístupového bodu “192.168.2.2”.
3. Zobrazí se hlavní obrazovka a průvodce nastavením. Průvodce konfigurací se skládá z 5 kroků. Podle pokynů krok za krokem připravte PrimeAX 1-2-3. Kliknutím na tlačítko Run Wizard spustíte průvodce nastavením.
III-1. Krok 1 (Změna uživatelského jména / hesla) Zadejte nové uživatelské jméno, nové heslo a potvrďte heslo, poté klikněte na tlačítko “Next”. POZNÁMKA: Heslo musí mít 6 až 32 znaků.
III-2. Krok 2 (Časové pásmo) Vyberte časové pásmo vhodné pro váš server. Poté potvrďte kliknutím na tlačítko Next.
III-3. Krok 3 (Zjištění zařízení) Device Discovery Tool objeví všechny přístupové body PrimeAX 1-2-3 v síti a zobrazíjejich MAC adresu, název, model, IP adresu a stav. Když jsou přístupové body PrimeAX 1-2-3 zapnuty a správně připojeny k síti, lze je zjistit pomocíDevice Discovery Tool. Položka Popis MAC Address PrimeAX 1-2-3 MAC adresa. Device Name Název PrimeAX 1-2-3. Model Model PrimeAX 1-2-3. IP Address PrimeAX 1-2-3 IP adresa.
Ikona stavu Ikona Barva Šedá Červená Stav Popis Spravovaný přístupový bod je odpojen. Zkontrolujte síťové připojení a ujistěte Odpojeno se, že spravovaný přístupový bod je ve stejné podsíti IP jako kontrolér. Zabezpečení systému musí být stejné Chyba autorizace pro všechny přístupové body. Zkontrolujte nastavení zabezpečení. nebo Všechny přístupové body musí mít stejnou verzi firmwaru. Použijte funkci aktualizace firmwaru kontroléru.
III-4. Krok 4 (Konfigurace bezdrátové sítě) Tato stránka umožňuje konfigurovat bezdrátovou síť PrimeAX 1-2-3. 1. Zadejte názvy sítí2.4GHz a 5GHz. 2. Klikněte na “Encryptions” a vyberte typ šifrování. 3. Do pole Password zadejte heslo pro sítě 2.4GHz a 5GHz. 4. Potvrďte kliknutím na tlačítko Next. POZNÁ MKA: Kliknutím na tlačítko Hide network můžete povolit nebo zakázat skrytí názvů sítí 2.4GHz a 5GHz.
III-5. Krok 5 (Potvrzení) Po dokončení nastavení v krocích 1 až 4 se zobrazí potvrzovací stránka. Zkontrolujte správnost všech nastavení. Potvrďte kliknutím na tlačítko Apply. POZNÁMKA: Nezavírejte stránku ani nevypínejte napájení, když se zařízení restartuje.
POZNÁ MKA: Pokud se pokusíte průvodce spustit znovu po dokončení nastavení průvodce, zobrazíse varovná zpráva, jak je uvedeno níže. Kliknutím na tlačítko Agree ukončete průvodce nebo kliknutím na tlačítko Run Wizard spusťte konfigurace.
IV. Režim Master a Salve PrimeAX 1-2-3 může pracovat v jednom ze dvou režimů Master nebo Slave. Postupujte podle níže uvedených pokynů. 1. Přejděte na hlavní obrazovku PrimeAX 1-2-3. 2. Vytáhněte nabídku pro změnu režimu a vyberte režim Slave nebo Master. 3. Zobrazí se varovná zpráva. Pokračujte kliknutím na OK nebo kliknutím na Cancel zavřete dialogové okno.
4. Zařízení se restartuje. V. Přidání dalšího PrimeAX +1(Slave) Chcete-li do hlavního přístupového bodu přidat další přístupový bod PrimeAX +1(slave), postupujte podle pokynů níže. 1. Připojte napájecí adaptér k přístupovému bodu (Slave) a zásuvky. Chvíli počkejte, než se přístupový bod spustí. Zařízení je připraveno, když se LED změní na modrou. 2. Připojte PrimeAX (Slave) ke stejné síti jako přístupový bod Master.
VI. Reset Pokud během používání zaznamenáte nějaké problémy, můžete přístupový bod resetovat do továrního nastavení. 1. Stiskněte a držte tlačítko Reset po dobu alespoň 10 sekund a poté tlačítko uvolněte. Pro stisknutí tlačítka Reset pravděpodobně budete potřebovat jehlu nebo podobný tenký předmět. 2. Chvíli počkejte, než se přístupový bod spustí. Jakmile se LED změní na modrou, je přístupový bod připraven k nastavení.
COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU, 2014/35/EU. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2014/53/EU, 2014/35/EU. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 2014/53/EU, 2014/35/EU.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European Radio Equipment Directive. Equipment: AX1800 Dual-Band Ceiling Mount PoE AP Model No.: PrimeAX 1-2-3/PrimeAX +1 The following European standards for essential requirements have been followed: Directives 2014/53/EU Spectrum : EN 300 328 V2.2.2 (2019-07) EN 301 893 V2.1.1 (2017-05) EMC : EN 301 489-1 V2.2.
Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code.
intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2.
Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions.