PrimeAX 1-2-3 & PrimeAX +1 Snelstartgids 06-2021 / v1.
Inhoud I. Productinformatie ....................................................1 I-1. Inhoud van de verpakking ................................................................. 2 I-2. Systeemvereisten ............................................................................. 3 I-3. Hardware-overzicht .......................................................................... 4 I-4. LED-status........................................................................................ 5 II.
I. Productinformatie De PrimeAX 1-2-3 met voorgeconfigureerde master en slave AP's, is een eenvoudig, compleet en schaalbaar Wi-i-systeem met Wi-Fi 6-technologie voor draadloze snelheden tot wel 1800Mbps.
I-1.
Voor PrimeAX +1: PrimeAX +1 Plafond ontagebeugel x1 Ethernetkabel x 1 PrimeAX 1-2-3 (Slave) QIG I-2.
I-3.
Nr. Beschrijving 1 Ethernetpoort (PoE) 2 Voedingsaansluiting (12V/1.5A) 3 Resetknop 4 I-4. LED LED-status Kleur Status Aan Blauw Langzaam knipperend Beschrijving Voeding is ingeschakeld. Bezig met upgraden van de firmware. Snel knipperend Terugzetten naar fabrieksinstellingen. Rood Uit Aan Knipperend Uit Bezig met opstarten. Fout. Voeding uitgeschakeld.
II. Hardware-installatie Dit onderdeel begeleidt u door de stappen die nodig zijn om uw PrimeAX 1-2-3te installeren. Router of Switch: Sluit een computer aan op een router of PoE met behulp van een Ethernetkabel.
II-1. Sluit het AP aan op een router Als de router gebruikt wordt; steek de voedingsadapter in de AP en steek de voedingsadapter in een stopcontact. Wacht a.u.b. een moment totdat het AP opgestart is. Het access point is gereed als de LED blauw is.
II-2. Verbinding maken met een PoE switch Als u een PoE-switch gebruikt, zorg dan dat de Ethernetkabel verbonden is met de Ethernetpoort van de PoE switch. Het AP wordt aangedreven door de switch. Wacht a.u.b. een moment totdat het AP opgestart is. Het access point is gereed als de LED blauw is. Gebruik de adapter niet als u een PoE switch gebruikt. NB: Controleer a.u.b. Of de PrimeAX (master en slave) voorgeconfigureerd zijn, volg de stappen hierboven om de ihardwareinstallatie te voltooien.
II-3. Een extra PrimeAX +1(slave) toevoegen Sluit de Ethernetkabel aan op de PrimeAX (slave) Ethernetpoort. De PrimeAX (Master) detecteert de nieuwe PrimeAX (Slave) automatisch. Twee apparaten worden gekoppeld. III. Setup Wizard De setup Wizard helpt u bij de setup van uw PrimeAX 1-2-3 en het configureren van de basisinstellingen. Volg de onderstaande instructies om toegang te krijgen tot de online gebruikersinterface (UI) van de PrimeAX 1-2-3. 1.
3. Het home-scherm en de Setup Wizard worden weergegeven. Er zijn 5 stappen om de wizard setup te voltooien. Volg de stappen om uw PrimeAX 1-2-3 stap voor stap te configureren. Klik op Uitvoeren (Run) om de wizard te starten.
III-1. Setup 1 (veranderen van Gebruikersnaam/Wachtwoord) Voer uw nieuwe gebruikersnaam, nieuw wachtwoord en bevestigd wachtwoord in, en klik op "Volgende” (next). NB: Het wachtwoord moet bestaan uit 6-32 tekens.
III-2. Setup 2 (Tijdzone) Kies de juiste tijdzone voor uw server. Klik daarna op Volgende (next) om te bevestigen.
III-3. Setup 3 (Device Discovery Tool) De Device Discovery functie detecteert alle PrimeAX 1-2-3 AP's binnen het netwerk, met MAC-adres, apparaatnaam, model, IP-adres en status. Zodra de PrimeAX 1-2-3 aangesloten zijn op voeding en op het netwerk, kunnen ze worden gezien met behulp van Device Discovery. Onderdeel Beschrijving MAC-adres Mac-adres van de PrimeAX 1-2-3. Apparaatnaam Apparaatnaam van de PrimeAX 1-2-3. Model Modelnaam van de PrimeAX 1-2-3. IP-adres IP-adres van de PrimeAX 1-2-3.
Statuspictogram Pictogr Kleur am Grijs Rood Oranje Geel Status Managed AP is verbroken. Controleer de Verbinding netwerkverbinding en zorg ervoor dat het AP verbroken zich in hetzelfde IP-subnet bevindt als de AP-controller. De systeembeveiliging moet voor alle AP's binnen het AP-bereik hetzelfde zijn. Authenticatiefo Controleer a.u.b. de beveiligingsinstellingen. ut of incomplete Alle AP's moeten dezelfde firmwareversie NMS-versie hebben. Gebruik de firmware upgrade functie van de AP controller.
III-4. Setup 4 (Wi-Fi-instellingen) De pagina helpt u om de draadloze instellingen van de PrimeAX 1-2-3 te configureren. 1. Voer de 2.4GHz en 5GHz SSID-naam in 2. Klik op "Versleuteling” en selecteer het gewenste beveiligingstype. 3. Voer het gewenste 2.4GHz en 5GHz wachtwoord in in het wachtwoordveld. 4. Klik op Volgende om verder te gaan. NB: U kun het SSID van 2.4GHz en 5GHz verbergen of weergeven door te klikken op de Verbergen (hide) knop.
III-5. Setup 5 (bevestiging) Nadat u de setup 1~4 van de Wizard heeft doorlopen en voltooid, wordt de Bevestigingspagina weergegeven. Controleer of alle configuratie juist is. Klik op Toepassen om te bevestigen. NB: Schakel de voeding niet uit en vernieuw de pagina niet tijdens het herstartproces van het apparaat.
NB: Nadat u de PrimeAX 1-2-3 heeft doorlopen, krijgt u de volgende waarschuwing te zien als u de Wizard opnieuw op probeert te starten. Klik op Bevestigen om de Wizard af te sluiten of klik op Wizard uitvoeren om de setup te starten.
IV. Master & Slave modus De PrimeAX 1-2-3 ondersteunt schakelen tussen Master en Slave modus. Volg a.u.b. de onderstaande stappen. 1. Ga naar de hoofdpagina van de PrimeAX 1-2-3. 2. Scroll naar beneden naar het Slave-modus onderdeel. 3. Er wordt een waarschuwing weergegeven. Klik op de OK knop om verder te gaan of annuleer om het dialoogvenster te sluiten.
4. Het apparaat zal herstarten. V. Een extra PrimeAX +1(slave) koppelen Volg a.u.b de ondestaande stappen om een extra PrimeAX slave access point te koppelen met het master acces point. 1. Sluit de voedingsadapter aan op de voedingspoort van het Slave AP en steek de voedingsadapter in het stopcontact. Wacht a.u.b. een moment totdat het AP opgestart is. Het AP is klaar als de LED Blauwis. 2. Sluit de PrimeAX Slave AP's aan op hetzelfe netwerk als de Master AP.
VI. Resetten Als u problemen ondervindt met uw AP dan kunt u het apparaat terugzetten naar de standaard fabrieksinstellingen. 1. Druk op de resetknop op het AP en houd deze ten minste gedurende 10 seconden ingedrukt, laat daarna de knop los. Wellicht moet u een speld of gelijksoortig scherp object gebruiken om de resetknop in te drukken. 2. Wacht tot het AP opnieuw is opgestart. Het access point is klaar voor de set-up wanneer de LED blauw is.
COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU, 2014/35/EU. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2014/53/EU, 2014/35/EU. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 2014/53/EU, 2014/35/EU.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European Radio Equipment Directive. Equipment: AX1800 Dual-Band Ceiling Mount PoE AP Model No.: PrimeAX 1-2-3/PrimeAX +1 The following European standards for essential requirements have been followed: Directives 2014/53/EU Spectrum : EN 300 328 V2.2.2 (2019-07) EN 301 893 V2.1.1 (2017-05) EMC : EN 301 489-1 V2.2.
Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code.
intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2.
Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions.