PrimeAX 1-2-3 e PrimeAX +1 Guida di installazione rapida 06-2021 / v1.
Sommario I.Informazioni sul prodotto ...........................................1 I-1. Contenuti della confezione ................................................................ 2 I-2. Requisiti di sistema ........................................................................... 3 I-3. Panoramica Hardware ...................................................................... 4 I-4. LED di stato ...................................................................................... 5 II.
I. Informazioni sul prodotto PrimeAX 1-2-3 con AP Master e Slave preconfigurati è un sistema Wi-Fi semplice, sicuro, completo ed espandibile, dotato di tecnologia Wi-Fi 6 per velocità wireless fino a 1800Mbps. Prestazioni di livello elevato e qualità combinati con funzionamento user-friendly, allestimento semplice, velocità wireless super veloce, ampio set di funzionalità e design pratico con montaggio a soffitto lo rendono una soluzione dual-band ideale per ambienti aziendali.
I-1.
Per PrimeAX +1: PrimeAX +1 PrimeAX 1-2-3 (Slave) Guida di installazione rapida I-2.
I-3.
No. Descrizione 1 Porta Ethernet (PoE) 2 Power Jack (12V/1,5A) 3 Tasto Reset 4 I-4. LED LED di stato Colore Stato Acceso Blu Rosso Spento Descrizione L'alimentazione è accesa. Lampeggia lentamente Aggiornamento del firmware. Lampeggia velocemente Ripristino alle impostazioni di fabbrica. Acceso Avvio. Lampeggiante Errore. Spento Alimentazione spenta.
II. Installazione hardware Questa sezione ti guiderà nei passaggi necessari all’installazione di PrimeAX 1-2-3. Router o Switch: Collega un AP al router o a uno switch PoE attraverso un cavo Ethernet.
II-1. Collegare l’AP al router Nel caso in cui si utilizzi il router, collegare l'adattatore di alimentazione all’AP e collegare l'adattatore di alimentazione a una presa a muro. Attendere un istante finché l’AP non si avvia. L’AP è pronto quando il LED è blu.
II-2. Collegare l’AP a uno switch PoE Nel caso in cui sia utilizzato uno switch PoE, assicurarsi che il cavo Ethernet risulti collegato alla porta Ethernet dallo switch PoE. L’AP verrà alimentato dallo switch. Attendere un istante finché l’AP non si avvia. L’AP è pronto quando il LED è blu. Non utilizzare l'adattatore di alimentazione se si sta utilizzando un interruttore PoE.
II-3. Aggiungere PrimeAX addizionali +1(Slave) Basta collegare il cavo Ethernet alla porta Ethernet PrimeAX (Slave). PrimeAX (Master) rileverà automaticamente PrimeAX (Slave). E i due dispositivi saranno accoppiati. III. Installazione Guidata La procedura guidata di installazione vi aiuterà a configurare PrimeAX 1-2-3 e le sue impostazioni di base. Segui i passaggi qui sotto per accedere all’UI web di PrimeAX 1- 2- 3. 1. Aprire un browser web ed inserire l'indirizzo IP di default del AP “192.168.2.
3. Appariranno la schermata Home e la procedura guidata di setup. La procedura comprende 5 passaggi da completare. Seguire il setup passo-passo per configurare PrimeAX 1-2-3. Fare clic sul pulsante “Avvia procedura guidata” per procedere con il setup.
III-1. Setup 1 (Cambiare nome utente/password) Inserire il nuovo nome utente, la nuova password e confermarla, quindi fare clic sul pulsante “Avanti”. NOTA: La password può contenere 6-32 caratteri.
III-2. Setup 2( Fuso orario) Scegliere il fuso orario corretto per il proprio server. Poi fare clic sul pulsante “Avanti” per confermare.
III-3. Setup 3 (Sistema di rilevamento dispositivi) Il sistema di rilevamento dispositivi individuerà tutti gli AP PrimeAX 1-2-3 della rete mostrando l’indirizzo MAC, il nome del dispositivo, il modello, l’indirizzo IP e lo stato. Una volta che gli AP PrimeAX 1-2-3 sono alimentati e correttamente collegati alla rete, possono essere individuati tramite il sistema di rilevamento.
Icone di stato Icona Colore Stato Definizione L’AP gestito è disconnesso. Controllare la connessione di rete e assicurarsi che l’AP Grigio Disconnesso gestito si trovi nella medesima sottorete IP del controller AP. La sicurezza del sistema deve essere la stessa per tutti gli AP nell’array AP. Verificare le Autenticazione impostazioni di sicurezza. fallita o Rosso versione NMS Tutti gli AP devono avere la stessa versione incompatibile firmware. Utilizzare la funzione di upgrade firmware del controller AP.
III-4. Setup 4 (Impostazioni Wi-Fi) Questa pagina vi aiuta a configurare le impostazioni wireless di PrimeAX 1-2-3. 1. Inserire il nome SSID per 2.4Ghz e 5GHz 2. Fare clic su “Criptaggio” e selezionare la modalità di sicurezza desiderata. 3. Inserire la password 2.4Ghz o 5GHz desiderata nel campo corrispondente. 4. Fare clic sul pulsante Avanti per confermare. NOTA: L’SSID 2.4Ghz e 5Ghz può essere nascosto o rivelato cliccando sul pulsante Nascondi rete.
III-5. Setup 5 (Conferma) Dopo aver completato i passaggi di setup 1-4 tramite la procedura guidata, verrà mostrata una pagina di conferma. Verificare che tutte le configurazioni risultino corrette. Fare clic sul pulsante “Applica” per procedere. NOTA: Non aggiornare la pagina o rimuovere l’alimentazione mentre il dispositivo si sta riavviando.
NOTA: Dopo aver completato la procedura guidata di setup per PrimeAX 1-2-3 se si tenta di lanciare di nuovo la procedura guidata, apparirà il messaggio di avviso mostrato di seguito. Fare clic sul pulsante Accetto per uscire dalla procedura guidato oppure Avvia procedura guidata per avviare il setup.
IV. Modalità master e slave PrimeAX 1-2-3 supporta il passaggio tra modalità master e slave. Segui i passaggi riportati di seguito. 1. Accedere alla pagina principale di PrimeAX 1-2-3. 2. Scorrere fino alla sezione Modalità slave. 3. Apparirà un messaggio di avviso. Fare clic sul pulsante OK per continuare o Cancella per chiudere la finestra di dialogo.
4. Il dispositivo inizierà il riavvio. V. Accoppiare PrimeAX addizionali +1(Slave) Seguire i passaggi elencati qui sotto per accoppiare punti di accesso aggiuntivi slave PrimeAX al punto di accesso master. 1. Connettere l’adattatore di alimentazione all’AP slave e collegarlo a una fonte di alimentazione. Attendere un istante finché l’AP non si avvia. L’AP è pronto quando il LED è Blu. 2. Collegare gli AP slave PrimeAX alla stessa rete dell’AP master.
VI. Reset Se si riscontrano problemi con l’AP, è possibile ripristinarlo alle impostazioni predefinite di fabbrica. 1. Tieni premuto il tasto reset sull’AP per almeno 10 secondi, quindi rilascia il tasto. Potrebbe essere necessario utilizzare uno spillo o un oggetto appuntito simile per premere il tasto reset. 2. Attendi il riavvio dell’AP. L’AP è pronto per la configurazione quando il LED di configurazione è di colore blu.
COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU, 2014/35/EU. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2014/53/EU, 2014/35/EU. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 2014/53/EU, 2014/35/EU.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European Radio Equipment Directive. Equipment: AX1800 Dual-Band Ceiling Mount PoE AP Model No.: PrimeAX 1-2-3/PrimeAX +1 The following European standards for essential requirements have been followed: Directives 2014/53/EU Spectrum : EN 300 328 V2.2.2 (2019-07) EN 301 893 V2.1.1 (2017-05) EMC : EN 301 489-1 V2.2.
Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code.
intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2.
Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions.