PrimeAX 1-2-3 & PrimeAX +1 Rýchla inštalačná príručka 06-2021 / v1.
Obsah I. Informácie o produkte................................................1 I-1.Obsah balenia ........................................................................................ 2 I-2.Systémové požiadavky ........................................................................... 3 I-3.Prehľad hardvéru ................................................................................... 4 I-4.Stav LED .................................................................................................
I. Informácie o produkte PrimeAX 1-2-3 s predkonfigurovanými prístupovými bodmi Master a Slave, je jednoduchý, bezpečný, kompletný a rozšíriteľný systém Wi-Fi s technológiou Wi-Fi 6 poskytujúce bezdrôtové rýchlosti až 1800Mbps.
I-1.
PrimeAX +1: PrimeAX +1 PrimeAX 1-2-3 (Slave) Rýchla inštalačná príručka I-2.
I-3.
I-4. Číslo Popis 1 Ethernetový port (PoE) 2 Napájacíport (12V/1.
II. Inštalácia hardvéru Pri inštalácii PrimeAX 1-2-3 postupujte podľa pokynov nižšie. Router alebo prepínač: Pripojte prístupový bod k routeru alebo prepínaču PoE pomocou ethernetového kábla.
II-1 Pripojenie prístupového bodu k routeru Ak používate router, pripojte napájací adaptér k prístupovému bodu a zásuvky. Chvíľu počkajte, než sa prístupový bod spustí. Zariadenie je pripravené, keď sa LED zmenína modrú.
II-2 Pripojenie prístupového bodu k prepínaču PoE Ak používate prepínač PoE, uistite sa, že je kábel Ethernet pripojený k portu Ethernet na prepínači PoE. Prístupový bod bude napájaný prepínačom. Chvíľu počkajte, než sa prístupový bod spustí. Zariadenie je pripravené, keď sa LED zmenína modrú. Ak používate prepínač PoE, nepoužívajte napájací adaptér. POZNÁ MKA: Upozorňujeme, že PrimeAX (Mater & Slave) je predkonfigurovaný, dokončite inštaláciu hardvéru podľa vyššie uvedených krokov.
II-3 Pridanie ďalšieho PrimeAX +1(Slave) Jednoducho zapojte ethernetový kábel do ethernetového portu PrimeAX (Slave). PrimeAX (Master) automaticky detekuje PrimeAX (Slave). Zariadenia budú spárované. III. Rýchle nastavenie Sprievodca nastavením vám pomôže nakonfigurovať PrimeAX 1-2-3 a jeho základné nastavenia. Podľa nižšie uvedených pokynov sa prihláste na konfiguračnú stránku PrimeAX 1-2-3. 1. Otvorte prehliadač a do adresného riadku zadajte predvolenú IP adresu prístupového bodu “192.168.2.2”.
3. Zobrazísa hlavná obrazovka a sprievodca nastavením. Sprievodca konfiguráciou sa skladá z 5 krokov. Podľa pokynov krok za krokom pripravte PrimeAX 1-2-3. Kliknutím na tlačidlo Run Wizard spustíte sprievodcu nastavením.
III-1. Krok 1 (Zmena používateľského mena / hesla) Zadajte nové užívateľské meno, nové heslo a potvrďte heslo, potom kliknite na tlačidlo “Next”. POZNÁMKA: Heslo musí mať 6 až 32 znakov.
III-2. Krok 2 (Časové pásmo) Vyberte časové pásmo vhodné pre váš server. Potom potvrďte kliknutím na tlačidlo Next.
III-3. Krok 3 (Zistenie zariadenia) Device Discovery Tool objavia všetky prístupové body PrimeAX 1-2-3 v sieti a zobrazíich MAC adresu, názov, model, IP adresu a stav. Keď sú prístupové body PrimeAX 1-2-3 zapnuté a správne pripojené k sieti, možno ich zistiť pomocou Device Discovery Tool. Položka Popis MAC Address PrimeAX 1-2-3 MAC adresa. Device Name Názov PrimeAX 1-2-3. Model Model PrimeAX 1-2-3. IP Address PrimeAX 1-2-3 IP adresa.
Ikona stavu Ikona Farba Šedá Červená Stav Popis Spravovaný prístupový bod je odpojený. Skontrolujte sieťové pripojenie a uistite Odpojené sa, že spravovaný prístupový bod je v rovnakej podsieti IP ako kontrolér. Zabezpečenie systému musí byť rovnaké Chyba autorizácie pre všetky prístupové body. Skontrolujte nastavenia zabezpečenia. alebo Všetky prístupové body musia mať rovnakú verziu firmvéru. Použite funkciu aktualizácia firmvéru kontroléru.
III-4. Krok 4 (Konfigurácia bezdrôtovej siete) Táto stránka umožňuje konfigurovať bezdrôtovú sieť PrimeAX 1-2-3. 1. Zadajte názvy sietí2.4GHz a 5GHz. 2. Kliknite na “Encryptions” a vyberte typ šifrovania. 3. Do poľa Password zadajte heslo pre siete 2.4GHz a 5GHz. 4. Potvrďte kliknutím na tlačidlo Next. POZNÁMKA: Kliknutím na tlačidlo Hide network môžete povoliť alebo zakázať skrytie názvov sietí 2.4GHz a 5GHz.
III-5. Krok 5 (Potvrdenie) Po dokončení nastavenia v krokoch 1 až 4 sa zobrazí potvrdzovacie stránka. Skontrolujte správnosť všetkých nastavení. Potvrďte kliknutím na tlačidlo Apply. POZNÁMKA: Nezatvárajte stránku ani nevypínajte napájania, keď sa zariadenie reštartuje.
POZNÁ MKA: Ak sa pokúsite sprievodcu spustiť znovu po dokončení nastavenia sprievodcu, zobrazí sa varovná správa, ako je uvedené nižšie. Kliknutím na tlačidlo Agree ukončite sprievodcu alebo kliknutím na tlačidlo Run Wizard spustite konfigurácie.
IV. Režim Master a Salve PrimeAX 1-2-3 môže pracovať v jednom z dvoch režimov Master alebo Slave. Postupujte podľa nižšie uvedených pokynov. 1. Prejdite na hlavnú obrazovku PrimeAX 1-2-3. 2. Vytiahnite ponuku pre zmenu režimu a vyberte režim Slave alebo Master. 3. Zobrazí sa varovná správa. Pokračujte kliknutím na OK alebo kliknutím na Cancel zatvorte dialógové okno.
4. Zariadenie sa reštartuje. V. Pridanie ďalšieho PrimeAX +1(Slave) Ak chcete do hlavného prístupového bodu pridať ďalší prístupový bod PrimeAX (slave), postupujte podľa pokynov nižšie. 1. Pripojte napájací adaptér k prístupovému bodu (Slave) a zásuvky. Chvíľu počkajte, než sa prístupový bod spustí. Zariadenie je pripravené, keď sa LED zmenína modrú. 2. Pripojte PrimeAX (Slave) k rovnakej sieti ako prístupový bod Master.
VI. Reset Ak počas používania zaznamenáte nejaké problémy, môžete prístupový bod resetovať do továrenského nastavenia. 1. Stlačte a držte tlačidlo Reset po dobu aspoň 10 sekúnd a potom tlačidlo uvoľnite. Pre stlačenie tlačidla Reset pravdepodobne budete potrebovať ihlu alebo podobný tenký predmet. 2. Chvíľu počkajte, než sa prístupový bod spustí. Akonáhle sa LED zmenína modrú, je prístupový bod pripravený na nastavenia.
COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU, 2014/35/EU. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2014/53/EU, 2014/35/EU. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 2014/53/EU, 2014/35/EU.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European Radio Equipment Directive. Equipment: AX1800 Dual-Band Ceiling Mount PoE AP Model No.: PrimeAX 1-2-3/PrimeAX +1 The following European standards for essential requirements have been followed: Directives 2014/53/EU Spectrum : EN 300 328 V2.2.2 (2019-07) EN 301 893 V2.1.1 (2017-05) EMC : EN 301 489-1 V2.2.
Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code.
intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2.
Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions.