SP-1101W User Manual 11-2013 / v1.
Copyright ＠ Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
I. Product Information .............................................................................. 1 I-1. Package Contents ............................................................................... 1 I-2. Front Panel ........................................................................................ 1 I-3. LED Status .......................................................................................... 2 I-4. Switch Status Button ........................................................
I. Product Information I-1. Package Contents Smart Plug Switch I-2.
I-3. LED Status LED Switch Status Color Status Description On Smart plug output power socket is on. Off Smart plug output power socket is off. On Smart plug is powered on. Off Smart plug is off. Green Power Green Quick Flashing Red Network Green Smart plug is starting up or restarting. Slow Flashing (1 Smart plug is in installation mode and x per second) ready for setup. Smart plug is connected to wireless On network and cloud.
I-5. Product Label The product label, which is located on the back of the smart plug switch, displays the input/output power and the default password of your smart plug. The password should be changed when you have finished the installation process for security purposes. The password is required to access the smart plug switch remotely. I-6. Reset If you experience problems with your smart plug, you can reset the plug back to its factory default settings.
II. Hardware Installation Follow the instructions below to ensure your smart plug is properly connected and ready for setup. If you have multiple smart plugs to set up, please only plug in and set up one smart plug at a time. 1. Plug the smart plug into a power socket. 2. Wait a few moments for the smart plug to start up. The smart plug is ready for setup when the network LED is flashing slowly red to indicate installation mode.
III. Smart Plug Setup III-1 Download EdiPlug App To set up your smart plug with the free EdiPlug smartphone app, please download the EdiPlug app and then follow the setup instructions for iOS or Android. After setup, you can use the EdiPlug app to switch your smart plug switch on/off remotely from any smartphone with an Internet connection, as well as set up automated schedule and email notifications. 1. Search the Apple App Store or Google Play for “EdiPlug”. 2. Download and install the app. 3.
III-2. Install a Smart Plug iOS Follow the instructions below to add a new smart plug to the EdiPlug app on iOS: You must be within Wi-Fi range of the smart plug. If you have multiple smart plugs, please only plug in and set up one plug at a time. 1. Search for a Wi-Fi network named “EdiPlug.Setup” and connect to it, as shown below: 2.
3. Enter your Wi-Fi password and tap “OK”. The next screen will indicate that setup is complete! 4. Your smart plug will now be displayed on the EdiPlug main screen. Slide the switch to switch the your smart plug (and any electrical device you plug into it) on or off. 5. The smart plug’s network LED should display on and green to indicate a successful network and cloud connection. You can use the EdiPlug app to control your smart plug remotely from any Internet connection.
Android Follow the instructions below to add a new smart plug to the EdiPlug app on Android: You must be within Wi-Fi range of the smart plug. If you have multiple smart plugs, please only plug in and set up one plug at a time. 1. Open the EdiPlug app and click the “+” icon in the top-right corner of the screen. 2. Tap “Install a New Plug” and select your Wi-Fi network from the list, as shown below.
3. Enter your Wi-Fi password and tap “OK”. The next screen will indicate that setup is complete! 4. Your smart plug will now be displayed on the EdiPlug main screen. Slide the switch to switch your smart plug (and any electrical device you plug into it) on or off. 5. The smart plug’s network LED should display on and green to indicate a successful network and cloud connection. You can use the EdiPlug app to control your smart plug remotely from any Internet connection.
III-3 Change Smart Plug Name & Password iOS 1. Select “Edit” from the EdiPlug main screen and then select the smart plug which you wish to edit from the list. 2. Enter a new name and password for your smart plug and tap “Back” to go back to the main screen. Your smart plug will now be displayed under its new name.
Android 1. Select “Edit” from the EdiPlug main screen and then select the smart plug which you wish to edit from the list. 2. Enter a new name and password for your smart plug and tap “Back” to go back to the main screen. Your smart plug will now be displayed under its new name.
III-4 Add an Existing Smart Plug to the Main Screen iOS 1. From the EdiPlug main screen, click the “+” icon in the top-right corner and select a plug from the list. 2. Enter your smart plug password and tap “OK”. Click “Back” icon on the next screen to finish.
Android 1. From the EdiPlug main screen, click the “+” icon in the top-right corner and select a plug from the list. 2. Enter your smart plug password and tap “OK”. Click “Back” on the next screen to finish.
III-5 Set the Schedule iOS 1. Select “Edit” from the EdiPlug main screen and then choose the device that you wish to edit. Press “>” to enter the detail settings. 2. Select “Schedule” and then able or disable the control functions by sliding the button to blue or white. Press “>”on the right of the screen if you want to edit the schedule for that day.
3. On the edit schedule page, areas in gray indicate the switch is “off”, areas in yellow indicate the switch is “on”. Slide arrows right on the time bar to select switch “on” period and left to select switch “off” period. Touch the yellow or gray area to adjust functions at that time. Press “Done” to save settings and go back to previous page. 4. On the editing detail period page, areas in gray indicate the switch is “off”, areas in yellow indicate the switch is “on”.
5. Press the time bar, as shown in the left picture, to show the detail schedule settings which have been set as shown in the right picture. Android 1. Select “Edit” from the EdiPlug main screen and then choose the device that you wish to edit. Press “>” to enter the detail settings.
2. Select “Schedule” and then able or disable the control functions by sliding the button to blue or white. Press “>”on the right of the screen if you want to edit the schedule for that day. On the edit schedule page, areas in gray indicate the switch is “off”, areas in yellow indicate the switch is “on”. Slide arrows right on the time bar to switch “on” and left to switch “off”. Touch the yellow or gray area to adjust functions at that time. Press “Done” to save settings and go back to previous page.
3. On the editing detail period page, areas in gray indicate the switch is “off”, areas in yellow indicate the switch is “on”. Slide arrows right to switch “on” and left to switch “off”. Swipe where the red arrows are below to go to next or previous hour period. Press “Done” to save settings and go back to previous page. 4. Click the yellow area, as shown in the left picture, to show the detail schedule settings which have been set as shown in the right picture.
III-6. Notification iOS 1. Select “Edit” from the EdiPlug main screen and then choose the device that you wish to set a notification for. Press “>” to enter the detail settings. 2. Select “Notification” in order to set an email notification. Select the “Gmail” service or other mail service. Gmail service If you choose Gmail service to send notification email, please enter your email address and password. When finished, slide “Action Notifications” on to enable notifications.
Other mail service If you choose other mail service, please enter all the items as show as blow and slide “Action Notifications” on to enable notifications. See Table below for explanation of all points. Mail Service SMTP Server SMTP Port Recipient email Sender email SSL/TLS Select “User defined” to enter the information manually. Input the host name or IP address of the SMTP server for the email sender. This information can be provided by your email service provider.
SMTP Authentication Account Password Action Notification Select ‘Enable’ when your SMTP server requires authentication. This information can be provided by your email service provider. Input the SMTP account name when your SMTP server requires authentication. This information can be provided by your email service provider. Input the password used for SMTP server authentication. Select ‘ON’ to enable action notification and ‘OFF’ to disable action notification function. Android 1.
Other mail service If you choose other mail service, please enter all the items as show as blow and slide “Action Notifications” on to enable notifications. See Table below for explanation of all points. Mail Service Select “User defined” to enter the information manually. SMTP Server Input the host name or IP address of the SMTP server for the email sender. This information can be provided by your email service provider. SMTP Port Input the SMTP port number for the email sender.
SMTP Authentication Account Password Action Notification Consult your mail server administrator when in doubt. Select ‘Enable’ when your SMTP server requires authentication. This information can be provided by your email service provider. Input the SMTP account name when your SMTP server requires authentication. This information can be provided by your email service provider. Input the password used for SMTP server authentication.
III-7 Delete Smart Plug from Main List iOS 1. Select “Edit” from the EdiPlug main screen and then select the box next to the plug you want to delete. Then press “Delete” to delete the plug. Android 1. Select “Edit” from the EdiPlug main screen and press and hold one plug that you want to delete. Then press “Yes” in message box to delete the plug.
III-8 Reset to Default iOS 1. Select “Edit” from the EdiPlug main screen and then choose the device that you wish to reset to default. Press “>” to enter the detail settings. 2. Then press “Reset to default” in order to reset to default settings.
Android 1. Select “Edit” from the EdiPlug main screen and then choose the device that you wish to reset to default. Press “>” to enter the detail settings. 2. Then press “Reset to default” in order to reset to default settings.
III-9 Upgrade Firmware Step 1: you can download the latest version utility “FWUpgradeTool” from http://www.edimax.com/ FWUpgradeTool.html to your PC or notebook. Step 2 : Confirm your smart plug already connected to the same network as your PC or netebook. Step 3: Access utility “FWUpgradeTool” and choose one plug you will upgrade and check the status to see if it can be upgraded or whether you already have the latest upgrade installed.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2006/95/EC, 2011/65/EC. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2006/95/CE, 2011/65/CE. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 2006/95/ES, 2011/65/ES.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European R&TTE directive 2006/95/EC, and directive 2011/65/EC(RoHS) . Equipment: Smart Plug Switch Model No.: SP-1101W The following European standards for essential requirements have been followed: ETSI EN 300 328 V1.7.1: 2006 ETSI EN 301 489-17 V2.1.1: 2009 ETSI EN 301 489-1 V1.9.
Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code.
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.
Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions.
34
