WS-2000P Series Quick Installation Guide 12-2016 / v1.
Package Contents Or WS-2001P Door/Window Sensor Or WS-2002P PIR Sensor WS-2003P Temperature & Humidity Sensor Or Two AAA Batteries (for WS-2001P) Three AAA Batteries (for WS-2002P /2003P) CD-ROM LED Status LED Color LED Status Description Red Flashing Pairing active 2 QIG
Smart Sensors A range of smart sensors are available to work with your IC-5170SC (sold separately) that can alert, notify and interact with smart rules via the EdiLife app. A WP-2001P door/window sensor consists of two parts (larger sensor unit and smaller magnetic contact) and can monitor when a door or window is opened. The WP-2002P PIR sensor is a heat-based motion detector. The WP-2003P Temperature and Humidity sensor can report temperature & humidity data. 1.
3.You need to pair each sensor to your sensor hub. Press the small button on the sensor hub in your IC-5170SC. The green LED will flash. 4.Within 10 seconds use a pencil or other object to press the small button on the front of your sensor for two seconds. 5.The sensor hub will pair with the sensor. The sensor’s LED will display red for a few seconds to indicate successful pairing. Repeat for each sensor.
6.Fix your sensors into the desired location using the high-strength adhesive strips on the back on each sensor. 7.For the two-piece door/window sensors, fix the larger sensor unit to the wall beside the door at a convenient height and close to the door frame. 8.Fix the small magnetic contact sensor to the door itself at the same height as the sensor unit, and on the same side of the door.
Smart Sensors: EdiLife App You can monitor the status of all your sensors using the EdiLife app, as well as setup your notifications and smart rules, or disable sensors as you wish. The app is easy and intuitive to use, but you can follow the guide below: 1.Select your IC-5170SC and tap the Settings icon in the top right corner. 2.Tap Sensors in the list and choose any of your sensors. If any of your sensors are not displayed, try pairing them again as explained in the previous chapter.
3.Adjust the settings for each sensor as you like and tap the check in the top right corner to confirm. 4.To setup Smart Rules, go back to the home screen and tap the menu icon in the top left, then select Smart Rules.
5.Smart Rules will be displayed here after you create them. Tap the + to create a new rule and choose which sensor to use. 6.Select which device will be triggered by your sensor’s event. (For the temperature/humidity sensor, you can additionally set the level which will trigger the rule e.g. above or below a specified temp/humidity.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1995/95/EC, 2011/65/EC. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 1995/95/CE, 2011/65/CE. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 1995/95/ES, 2011/65/ES.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European R&TTE directive (1999/5/EC, 2006/95/EC) . Model No.: WS-2001P Door / Window Sensor WS-2002P PIR Sensor WS-2003P Temp. & Humidity Sensor The following European standards for essential requirements have been followed: Spectrum: ETSI EN 300 440-2 V1.4.1:2010 ETSI EN 301 489-1 V1.9.2:2011 ETSI EN 301 489-3 V1.6.