User guide

ManualsBrandsEdsal ManualsFurniture1UGK7

Safety Instructions

These units should be placed on a level surface. Failure to do so can result in poor product performance or create a possible safety

hazard. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY PART OF THE

UNIT, OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the heavier loads on the bottom.

DO NOT OVERLOAD. Use care when working with metal parts.

When moving the unit, always push from the sides. NEVER push from the front, back, or top. This can cause a “tipping” hazard,

which can result in a serious injury to yourself or others. NEVER pull the unit during movement, push the unit to the location.

Always move the unit over a flat level surface. Rough surfaces cause the unit to vibrate, which causes the unit’s load to increase in

weight, or again may cause a “tipping” hazard which can result in a serious injury to yourself or others. Do not store any items on

the top of the unit during movement, this may cause a “falling” hazard that can injure yourself or others.

Instruction Manual - Mobile Bin Unit - 1UGK7

General Instructions

Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used on the beams

and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block of wood between the hammer

head and the parts to prevent damage. Tap gently and be sure the rivets are straight and fully engaged.

Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel free to contact our Edsal manufacturing facility at,

(773) 475-3000 and request customer service. We can also be reached on the internet at the following email address :

customerservice@edsal.com.

To obtain replacement parts, please provide the following information : Model # - Part # & Description - Location Purchased - Date Purchased

10 Shelf

33” w

36 Bins

Step 1

Install casters in to posts.

Press the plastic caster supports fully into the

welded bracket on the

bottom of each of the 4 posts.

Insert caster

Into Post bottom

Make sure caster

is fully inserted

Description Qty. Part # Size

Caster 4 Swivel Single 3"

Post 4 RUPT6302 63"

Beam - Double Rivet 4 RBBR3202 33"

Brace - Double Rivet 4 RBBR1402 15"

Beam - Single Rivet 16 RBBE3201 33"

Brace - Single Rivet 2 RBBE1401 15"

Wire Deck - 3 Large Bins 3 WD1533L 33" x 15"

Wire Deck - 4 Medium Bins 3 WD1533M 33" x 15"

Wire Deck - 5 Small Bins 3 WD1533S 33" x 15"

Wire Deck - Flat 1 WD1533 33" x 15"

Large Plastic Bin 9 PB15106 10.6" x 6.1" x 15.4"

Medium Plastic Bin 12 PB15076 7.5" x 6.3" x 15.4"

Small Plastic Bin 15 PB15063 6.0" x 3.3" x 15.4"

Summary of content (3 pages)

PAGE 1
Instruction Manual - Mobile Bin Unit - 1UGK7 10 Shelf - 33” w - 36 Bins Description Caster Post Beam - Double Rivet Brace - Double Rivet Beam - Single Rivet Brace - Single Rivet Wire Deck - 3 Large Bins Wire Deck - 4 Medium Bins Wire Deck - 5 Small Bins Wire Deck - Flat Large Plastic Bin Medium Plastic Bin Small Plastic Bin Qty.
PAGE 2
Step 2 Assemble the front and back frames. Using 2 of the 33” Double-Rivet Beams assemble the front frame as shown. Insert the rivets on the Beams into the slots on the Posts and gently tap down until they are fully seated. 33” long, 2 Rivet Beam Repeat the process to build a matching back frame.
PAGE 3
Step 4 Install the remaining 33” long, 1 Rivet Beams at the recommended hole spacing between beams. As before, insert the rivets on the Beams into the slots on the Posts and tap them down until they are fully seated. 2 Holes 2 Holes 2 Holes 4 Holes 4 Holes 33” long, 1 Rivet Beams 4 Holes 4 Holes 4 Holes 4 Holes Step 5 Beginning with the bottom level, install the Wire Decking and Bins. The Wire Decks are formed to fit either 3 large, 4 medium, or 5 small bins.