Instruction Manual

ManualsBrandsEFFYDESK ManualsStanding DeskEFFYDESK Home Frame 2022 Height-Adjustable Electric Standing Desk

Table Of Contents

Instruction Manual

M6X12

M6X8

M5X18

M6X16

Dx5

Zip Tie

Rubber Pad

M4X12

Gx8

M6X16

Crossbar

Control Box

Power Cable

Lifting Column

Foot

Extension Cord

Side Bracket

Keypad

M8X10

4mm Allen Key

(included)

Tape Measure

Ax8

Bx4

Cx12

Ex12

Fx2

Technical Data

Parts List

Tool Required

Accessory ListAccessory List

710-1160mm

Segment Column

240 lbs

Height Range

Recommend Load

<220 lbs

30mm/s

Screwdriver

If you have any issues with your product, please feel free to contact us via

team@effydesk.ca

Thank you for your order!

We will help you resolve the issue as soon as possible.

info@effydesk.ca

For more information, please visit

https://effydesk.ca/pages/how-to-assemble-your-height-adjustable-standing-desk

Hx8

Summary of content (8 pages)

PAGE 1
Instruction Manual Technical Data 2 Segment Column 240 lbs Recommend Load <220 lbs Height Range 710-1160mm Bx4 M6X12 M6X8 Dx5 Ex12 Zip Tie Rubber Pad UL Tool Required Accessory List Ax8 30mm/s Cx12 M5X18 or M6X16 4mm Allen Key (included) Tape Measure Fx2 Gx8 M4X12 Screwdriver M6X16 Hx8 M8X10 Parts List Control Box Extension Cord Power Cable Side Bracket 6 Keypad Lifting Column 7 Crossbar Foot 8 Thank you for your order! If you have any issues with your product, please fe
PAGE 2
STEP 1 Separate the Crossbar ⑧ and you will find the Crossbar Rail inside. Crossbar End STEP 2 A Crossbar Rail Insert one of the Crossbar Ends into the one of the Lifting Columns ③ and secure with screws. Repeat the same step for the other Lifting Column. 8 Allen Key 4mm STEP 3 B 4 Allen Key 4mm Crossbar End Attach the Side Bracket ⑥ to one of the Lifting Columns. Repeat the same step for the other Lifting Column.
PAGE 3
STEP 4 Slide the two Crossbar Ends back into the Crossbar Rail. Please make sure to fit the slots as shown below. Note: Please make sure the circular holes are facing inwards as shown below. Slider for Control box STEP 5 G 8 Allen Key 4mm Attach both Feet ④ to the bottom of the Lifting Columns.
PAGE 4
STEP 6 C Install the tabletop (Predrilled / Non-predrilled ). C 12 E 12 12 Allen Key 4mm Predrilled STEP 7 D Non-predrilled Connect all the cables to the Control Box ①. 5 Power Port Lifting Column Ports D 7 Lifting Column Ports Note : Use Zip Ties (D) to secure cables under the table.
PAGE 5
STEP 8 H 8 Allen Key 4mm F Firmly secure the Crossbar with Screws (A) and attach the Keypad ⑦ with Screws (F) to the tabletop. 2 Screwdriver H F STEP 9 Plug the cable from the Keypad into the Control Box and flip the table onto its feet. Power Port Lifting Column Ports Lifting Column Ports Keypad Port Note: The Control Box is equipped with a gyro sensor so the table and the Control Box must be level in order to work properly or else it will not move up and down.
PAGE 6
Before plugging in the table, make sure that The Lifting Columns are level and set at their lowest position. All the screws are tightened to avoid the desk becoming wobbly. Calibrate the desk by following the steps below: Please press the Down button and hold for 10-15 seconds until the table stutters and beeps. Release the button. Your desk is ready to use! Operation Guide Adjust the table to the desired height, then press M. “S-“ will flash on the display.
PAGE 7
Reset the table When an error code or “RST” appears on the display, please reset the table. ● ● ● ● Unplug the power cord from the Control Box. Unplug the cable that connects the Keypad to the Control Box. Wait 30 minutes and plug all the cables back in again. Press the Down button and hold for 10-15 seconds until the table stutters and beeps. Press by holding 10-15 seconds If“HOT” appears on the display ● Please unplug and replug and let it cool off for a couple of minutes before proceeding.
PAGE 8
If you have any questions, please contact us at team@effydesk.ca or info@effydesk.ca www.effydesk.