Tech Tips Diagrams Troubleshooting MSD TECH LINE: (915) 855 - 7123 www.msdignition.
® WIRING DIAGRAMS AND TECH NOTES MSD believes that customer service does not end at just producing the best ignition components available, but helping the customer is also a number one priority. That is why we have assembled this MSD Ignition Wiring Diagrams and Tech Notes Book. This book is a collection of component installation procedures, applications and technical information. Wiring descriptions and troubleshooting procedures for most MSD products can be found within these pages.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 TABLE OF CONTENTS General Tech Tips 6 Coil Compatibility List .................................................................................. 6 Distributor Setup Tips ................................................................................ 13 Flying Magnet Crank Trigger Tips ........................................................
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 TABLE OF CONTENTS MSD 10 Ignition Installation 64 Magnetic Pickup ...................................................................................... 66 Magnetic Pickup w/Timing Accessory .......................................................... 66 MSD DIS-2 & DIS-4 Ignition Installation 67 DIS-2 to 4-Cylinder Coil Pack ..............
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 COIL COMPATIBILITY LIST This chart lists the compatibility of various coils with MSD Ignition Controls. It is impossible to list every coil combination and it is recommended to check with the coil manufacturer before installation. #Indicates preferred coils for model indicated. YES - Coil is compatible with the model indicated.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 GENERAL INSTALLATION TIPS MOUNTING MSD Ignition Controls are designed to withstand underhood temperatures but should be mounted away from direct engine heat sources such as headers or manifolds. The ignition control can be mounted in most positions except upside down.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 GENERAL INSTALLATION TIPS Plastic Spacers MSD no longer supplies the plastic spacers that were used on some coil installations. This is due to the changes in coil housings and connectors not requiring the spacers. The spacers were used to simplify wiring on canister coil applications.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 GENERAL INSTALLATION TIPS Tachometer Compatibility List AFTERMARKET TACHOMETER AUTOGAGE AUTOMETER FORD MOTORSPORTS MALLORY MOROSO STEWART S.W.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 SPARK PLUG WIRES AND SPARK PLUGS Spark Plug Wires Spark plug wires have two main objectives; transfer the spark energy to the plugs and suppress the Electro Magnetic Interference (EMI) that the spark voltage projects.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 SPARK PLUGS WIRES AND SPARK PLUGS Plug Wire Tips Spark Plugs To keep your engine’s spark plug wires in tip-top condition there are a few simple steps you can take. For starters, apply a small amount of MSD Spark Guard, PN 8804, a dielectric grease, to each wire terminal.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 DISTRIBUTOR SETUP TIPS Distributor Setup MSD offers a variety of distributors designed for different applications ranging from low profile and small diameter models to a front drive distributor.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 DISTRIBUTOR SETUP TIPS Rotor Phasing Rotor phasing is the alignment between the rotor tip and the distributor cap terminal when the spark occurs. If the rotor tip is not aligned with the post when the spark occurs, the spark may find another path to ground resulting in scattered timing or a missfire.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MECHANICAL ADVANCE SETUP TIPS Most MSD Distributors with a magnetic pickup features an adjustable mechanical advance assembly. The distributors with this feature are supplied with three sets of advance springs and four stop bushings. The advance assembly is made up of weights, springs, an advance cam and an advance stop bushing.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 DIstributor Advance Graphs The following charts show the variety of ignition curves you can achieve with an MSD Distributor. Locking Out the Centrifugal Advance If you would like to lock out the centrifugal advance or are converting to a Flying Magnet Crank Trigger, the MSD centrifugal advance can easily be locked out.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 DISTRIBUTOR SETUP TIPS 3-In-1 Chevrolet Distributor Tool The MSD 3-In-1 Distributor Set Up Tool, PN 8599, allows you to perform three checks and measurements on Chevrolet engines: The oil pump intermediate shaft engagement, Setting the height of the adjustable slip collar on MSD Distributors, and Oil priming the engine prior to starting it.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 FLYING MAGNET CRANK TRIGGER TIPS The MSD Flying Magnet Crank Trigger System is the most accurate way possible to trigger the ignition. This is due to fact that the trigger signal is coming directly from the source of piston position in the cylinder; the crankshaft.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 INSTALLING AN MSD 5, PN 5200, OR BLASTER IGNITION, PN 5900 The MSD 5 and Blaster Ignitions are inductive ignitions which enhance the spark of the vehicle’s stock ignition. The MSD 5 is a multiple spark ignition, while the Blaster is a single spark, long duration design.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 BLASTER IGNITION TO MAGNETIC PICKUP Note: The MSD 5 Ignition does not have a magnetic pickup connector.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 INSTALLING AN MSD 6A, 6T, 6AL OR 6BTM IGNITION CONTROL This section covers the installation of the MSD 6A, 6AL, 6BTM, 6T and the SCI Ignition Controls. These Ignition Controls feature capacitive discharge circuitry and multiple sparks.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 6 SERIES TO POINTS/AMPLIFIER NOTE: On dual point setups, it is recommended to remove the trailing set of points. NOTE: Ballast Resistor is not necessary.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 6 SERIES WITH AN MSD TIMING ACCESSORY MSD 6 SERIES TO AN MSD READY-TO-RUN DISTRIBUTOR NOTE: The ignition module of the Ready to Run distributor still triggers the MSD.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 6 SERIES TO AN MSD PN 8460 DISTRIBUTOR NOTE: The PN 8460 distributor has been discontinued.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD AND LARGE CAP GM HEI DISTRIBUTORS There are three different large cap HEI distributors. To indentify which of the following diagrams fit you specific application, remove the distributor cap and rotor and locate the ignition module at the base of the distributor.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 6 SERIES TO GM HEI 4-PIN MODULE NOTE: The GM Ignition Module is removed and replaced with the MSD PN 8861 Wire Harness. See page 27. MSD 6 SERIES TO GM HEI 5 OR 7-PIN MODULE NOTE: Some 5-pin models may experience a hesitation or stall on decceleration.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 6 SERIES TO GM DUAL CONNECTOR COIL NOTE: MSD offers a direct plug in harness, PN 8876, for this coil. NOTE: Cut and splice the two pink wires (coil positive) together and connect to orange wire of MSD. Cut and splice the two white wires (coil negative) together and connect to the white of MSD.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 6 SERIES WITH GM HARNESS Harness PN 8876 - Dual Connector Coil. Harness PN 8877 - 1996-on GM Vehicles. MSD 6 SERIES WITH GM HARNESS AND TIMING CONTROL Harness PN 8876 - Dual Connector Coil. Harness PN 8877 - 1996-on GM Vehicles.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 6 SERIES TO FORD DURASPARK USING POINTS TRIGGER MSD 6 SERIES TO FORD DURASPARK USING MAGNETIC PICKUP NOTE: MSD Offers a harness, PN 8869, to connect the magnetic pickup connector to the Ford Duraspark connector.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 6 SERIES TO LATE MODEL DODGE WITH 2-PIN COIL MSD 6 SERIES TO JEEP WITH INTEGRATED COIL/MODULE ASSEMBLY MSD offers a Wiring Kit, PN 8813, that allows you to modify the original Jeep Ignition Module/Coil assembly. The drawing shows the installation with the coil already modified.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 6 AND SCI SERIES TO HONDA/ACURA WITH INTERNAL COIL MSD 6 AND SCI SERIES TO HONDA/ACURA WITH BLASTER COIL AND POWER CAP NOTE: MSD offers a variety of Honda Distributor Caps that accept an external coil wire.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 6 AND SCI SERIES TO FACTORY EXTERNAL COIL HONDA/ACURA MSD 6 AND SCI SERIES TO GENERAL IMPORT WIRING NOTE: Remove the coil terminal wires. The negative wire connects to MSD White. The positive wire connects to MSD small Red. The MSD Orange connects to the coil positive terminal, Black connects to the coil negative terminal.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 6 SERIES TO MAZDA ROTARY WITH SINGLE MSD UNIT ORIGINAL WIRES LEAVE DISCONNECTED + TRAILING COIL ORIGINAL WIRES TO "LEADING" COIL TO BATTERY + HEAVY RED + HEAVY BLACK TO BATTERY O ® N IGNITIO TACH OUTPUT GE N RA LEADING COIL K AC BL FROM IGNITION KEY AUTOTRONIC CONTROLS CORPORATION PART NO. SERIAL NO..
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 6 SERIES TO MALLORY UNILITE DISTRIBUTOR NOTE: A ballast resistor is not necessary.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 6 SERIES TO PERTRONIX KIT MSD 6 SERIES TO ACCEL BEI DISTRIBUTOR NOTE: The PN 8801 (BEI Quick Connect) is discontinued. If you did not find a schematic to match your application, or if you need assistance, please contact MSD Tech at (915) 855-7123.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 INSTALLING MSD 6TN, 6ALN AND 6HVC DUAL RACE IGNITIONS This section covers how to wire redundant ignition systems featuring the MSD 6TN, 6ALN, GM Heavy Duty Ignition and the 6 HVC Professional Ignition. These ignitions are designed primarily for circle track and road course racing where running a redundant ignition system is commonplace.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD DIGITAL-6 PLUS, PN 6520, AND DIGITAL-7 PLUS, PN 7520, IGNITIONS This section covers the MSD Digital-6 Plus and the Digital-7 Plus. These ignitions share the same wiring and functions. The main difference is that the Digital-7 Plus produces more spark energy and is intended for racing applications only.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 DIGITAL-6 OR 7 PLUS IGNITION PROGRAMMING Cylinder Select: The Digital Plus Series Ignitions are set at the factory for operation on an 8cylinder engine. For other engines, use the cylinder select dial. Start Retard: There is also an optional 20 degree start retard that will occur during cranking.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 INSTALLING AN MSD 7AL-2 AND 7AL-3 IGNITION CONTROL This section covers the MSD 7AL-2 and 7AL-3 Ignition Controls. These ignitions share the same wiring to run the vehicle, but the 7AL-3 has several optional accessories that can be connected.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 7AL-3 ACCESSORIES The 7AL-3 shares the same wiring colors and specifications as the 7AL-2 when it comes to coil terminals, battery supply voltage and triggering. However, the 7AL-3 has many accessories that can be used. The following information explains their wiring and operation.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 7 SERIES TO GM LARGE CAP HEI DISTRIBUTORS There are three different large cap HEI distributors. To indentify which of the following diagrams fit your specific application, remove the distributor cap and rotor and locate the ignition module at the base of the distributor.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 7 SERIES TO GM HEI 4-PIN MODULE DISTRIBUTOR NOTE: A Low Resistance HEI Rotor Bushing, PN 8412, must be used with an MSD 7AL Ignition.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 7AL-2 WITH MODULE SELECTOR AND MULTIPLE RETARD MSD 7AL-3 WITH REV LIMITERS NOTE: The rev limiter activates when 12 Volts are supplied to the "Burnout" or "Launch" terminal.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 7AL-3 USING RETARD FUNCTIONS NOTE: The retards will activate when removed from ground. The positive side of the solenoid will provide ground until activated. NOTE: If a stage is not used, a ZERO Degree module must be installed or the terminal must be grounded.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 7AL-3 USING RPM ACTIVATED SWITCH FOR SHIFT LIGHT The OUTPUT RAS Terminal will supply a Ground at the selected RPM. NOTE: A short jumper is supplied that can be used to provide a switched 12 Volts from the "IGN" terminal to the "RAS ON/OFF" terminal.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 INSTALLING AN MSD PROGRAMMABLE DIGITAL-7 IGNITION CONTROL This section covers the basic wiring and accessories of the MSD Programmable Digital-7 Ignition, PN 7530. This is a powerful ignition with a list of programmable timing and rpm features. It can be programmed with a PC or with MSD’s hand held Programmer/Monitor.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 PROGRAMMABLE WIRE OPERATION Power Leads Heavy Red Heavy Black Red Orange Black Trigger Wires White These are the two heavy 12 gauge wires and are responsible for getting direct battery voltage to the ignition. The Ignition is load protected from reverse battery connections and will automatically shut down if there is over 27 volts input.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 HAND HELD PROGRAMMER/MONITORS FOR MSD PROGRAMMABLE IGNITION For racers that do not use a PC to program their Programmable Digital Ignition Components, MSD offers two Programmer Monitors. These provide total programming control and feature an LCD monitor screen with push buttons for editing the programs.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 PN 7530 FLOW CHART WITH HAND HELD MONITOR, PN 7555 MENU TREE The following menu tree shows the different screens and programs of the PN 7530 and Monitor. Monitor List: 8 RpmSw OFF 1 ScanTime 1Sec 9 MaxCylDeg 2.2 2 CamSync NONE 10 TrigSrc NONE 3 Rpm 12500 11 Step1In OFF 4 RetSum 10.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 8 SERIES IGNITION CONTROLS This section covers the MSD 8 Series Ignition Controls. The MSD 8, PN 7800, is a race only ignition system. The MSD Pro Power Coil, PN 8201 is the only coil recommended for the MSD 8 Ignitions. A current filter, PN 8830, is also recommended to help suppress EMI noise and voltage spikes.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 8 IGNITION TO MAGNETIC PICKUP MSD DUAL COIL 8 IGNITION TO MAGNETIC PICKUP NOTE: The MSD Dual Coil 8, PN 7802, has been obsoleted.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 INSTALLING AN MSD 10 IGNITION CONTROL This section covers the MSD 10 Ignition Control. The MSD 10, PN 7500, is a race only ignition system and is unique in that it incorporates two ignition coils.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD 10 SERIES IGNITION INFORMATION UPDATE: Before connecting the MSD 10, inspect the Pro Power Coupler Coil. It must be Part Number 8209R. Originally, this Coil was solid black with the number PN 8209 but it was revised to a red housing with a new part number of PN 8209R. This running change also affected the wiring to the ignition Control.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 INSTALLING AN MSD DIS-2/DIS-4 IGNITION CONTROL This section covers the MSD DIS-2 and DIS-4 line of Ignition Controls. The DIS-2 Ignitions can be used on 4-cylinder engines equipped with two dual output coils. The DIS-4 Ignitions can be used on 4, 6 or 8-cylinder engines equipped with up to four dual output coils.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MAX/MIN REV LIMIT (+) Selector, S1, extends the range of the Max Speed Rev Limit and the Staging Rev Limit by 4000 rpm. Set selector S1 to ON to increase the indicated Rev Limit points by 4000 rpm.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD DIS-4 WITH A TYPICAL DISTRIBUTORLESS V-8 IGNITION Note: This will not work on coil per cylinder ignitions.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD STACKER IGNITION CONTROLS The Stacker Advantage The MSD Stacker Ignitions utilize the best characteristics of both the conventional factory inductive ignition and a multiple sparking, capacitive discharge (CD) ignition system.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD STACKER, PN 7000, TO FORD TFI CYLINDERS 8 6 4 CUT LOOPS NONE RED RED & BLUE RED A B C IGNITION DISTRIBUTOR PN 7000 7010 ORANGE RED/ LIGHT GREEN AUTOTRONIC CONTROLS CORPORATION B A 1490 HENRY BRENNAN DR.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD STACKER-4 TO 4-CYLINDER COIL PACK IGNITION NOTE: ONLY TWO CHANNELS ARE USED SO THE REMAINING TWO ORANGE WIRES MUST BE SPLICED INTO THE ACTIVE CHANNELS. COIL (-) TRIGGER 1 COIL (-) TRIGGER 2 COIL HARNESS COIL ORANGE COIL (+) 12 VOLTS IGNITION A B C D R RED E F ORANGE AUTOTRONIC CONTROLS CORPORATION 1490 HENRY BRENNAN DR.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 SOFT TOUCH REV CONTROLS The MSD Soft Touch Rev Control, PN 8728, is designed for inductive style ignition systems. It cannot be used with an MSD CD Ignition such as any 6 or 7 Series Ignition Control. The Rev Limit is set with plug-in rpm modules.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 SOFT TOUCH REV CONTROL PN 8728 WITH CHRYSLER MAGNETIC PICKUP Note: This Rev Control is not recommended for Chrysler Gold and Chrome Ignition boxes.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 TWO AND THREE STEP MODULE SELECTORS The MSD Two Step, PN 8739, Three Step, PN 8737, and Launch Control, PN 8735, Module Selectors allow you to switch between two or three different rpm or retard modules. The different modules are activated when 12 volts are applied to the corresponding wire.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD LAUNCH CONTROL, PN 8735 The 2-pin connector of the Launch Control can only be installed one way to operate correctly. There is an LED on the control that will light when the connector is in the correct position. Bare Wire: Connects to ground. This ground acts as an EMI shield for the wiring of the control.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD RPM ACTIVATED SWITCHES This section covers the MSD RPM Activated Switch, PN 8950, and the Window Switch, PN 8956. The PN 8950 will activate a circuit at a desired rpm by supplying or removing ground. The PN 8956 Window Switch will activate a circuit by supplying ground, then will deactivate the same circuit at a different rpm.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD RELAYS, SINGLE POLE, PN 8961, DOUBLE POLE, PN 8960 MSD Relays will allow you to activate a variety of accessories that require high current. These are ideal to tie in with rpm activated switches such as nitrous or air shifter solenoids or even a horn or fuel pump.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD RPM ACTIVATED SWITCH, SOLENOID AND PN 8961 RELAY RED 12 VOLTS RELAY PN 8961 86 30 85 NITROUS OR AIR SHIFT SOLENOID RED 87a YELLOW TM IGNITION RPM ACTIVATED SWITCH PN 8950 87 GRAY (NOT USED) WHITE TO MSD TACH TERMINAL OR COIL (-) TO GROUND BLACK TO GROUND AUTOTRONIC CONTROLS CORPORATION 1490 HENERY BRENNAN DR.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD SHIFT LIGHT, PN 8952 This section covers the MSD Shift Light, PN 8952. The Light will activate at a desired rpm which is controlled by MSD’s white RPM Modules. If no rpm module is installed in the Light, it will not turn on. The Light can be used with stock ignitions or with MSD Ignition Controls.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 SHIFT LIGHT PN 7552 The MSD Shift Light, PN 7552, features a bright LED that will alert you to shift at an rpm point. The Shift Light requires a 12 volt source (maximum of 18 volts) and ground. It is activated when a ground is supplied to complete the circuit. There is no polarity to the Light’s two Yellow wires.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 BOOST TIMING MASTER, PN 5462 The Universal Boost Timing Master, PN 5462, is a Timing Control and ignition enhancer in-one. It allows you to adjust the timing up to 15° as the boost pressure of the turbo or supercharger increases.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 UNIVERSAL BOOST TIMING MASTER TO FORD TFI ORIGINAL WIRE HARNESS DARK GREEN/ YELLOW RED/ LIGHT GREEN 1 2 0 3 DARK GREEN/ YELLOW WHITE BOOST RETARD GE ORAN RED (+) (-) COIL CONNECTOR TM IGNITION BOOST TIMING MASTER PART NO. 5462 AUTOTRONIC CONTROLS CORPORATION BLACK 1490 HENRY BRENNAN DR.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 TIMING CONTROLS FOR MSD IGNITIONS MSD offers a variety of Timing Controls that must be used with an MSD Ignition. Each Control has different functions and options but they share common wiring. The Controls wire before the Ignition and always connect to the MSD through the Ignition’s White wire, or Points terminal.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 BOOST TIMING MASTER FOR MSD IGNITIONS, PN 8762 WITH VACUUM ADVANCE , PN 8962 The Boost Timing Masters are designed to be used with an MSD Ignition Control. They allow you to retard the timing in relation to boost pressure created by a turbo or supercharger. Timing adjustments can be made by the driver with a dash mounted control knob.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 ADJUSTABLE TIMING CONTROL, PN 8680 The PN 8680 Timing Control easily connects to an MSD Ignition. Timing adjustments can be made by the driver with a dash mounted control knob. The timing can be retarded up to 15°. When the control knob is at full clockwise position, the timing will be at the factory setting.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 3-STAGE RETARD, PN 8970, AND MULTI-STEP RETARD, PN 8972 The 3-Stage Retard, PN 8970, supercedes the Multi-Step Retard, PN 8972. They both are designed to provide up to three different retard rates that can be activated at different times. The three stages are cumulative up to 20° (6° on first stage, 4° second, 2° third means 12° total).
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 DIGITAL RETARD PN 8975 The Digital Retard Control, PN 8975, provides up to four different retard rates that can be activated at different times. The four stages are cumulative up to 20° (6° on first stage, 4° second, 3° third, 2° fourth produces 15° total).
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 TIMING COMPUTER, PN 8980 The MSD Timing Computer has a built-in timing curve designed for engines with locked-out timing. It is an electronic version of a centrifugal advance. When the engine is cranking the timing retards 20° from the mechanical locked out timing and remains there until 1,000 rpm.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 PROGRAMMABLE TIMING CONTROL PN 8981 The MSD Programmable Timing Control allows you to program an advance curve for engines with locked-out timing. It is a programmable electronic version of a centrifugal advance. There is also an optional single stage of retard and 20° start retard.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 TIMING COMPUTER, PN 8981 All adjustments of the Timing Computer are taken from your Mechanical, or total timing setting. The Mechanical timing is set by the position of the crank trigger or distributor. Before making any adjustments, be sure to have your mechanical timing set to your specifications.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 START/RETARD CONTROL, PN 8982 The MSD Start Retard Control provides a start retard and a single stage of retard. The start retard can be set for 10° or 25° during cranking. When the engine is cranked, the timing will retard until the engine reaches over 1,300 rpm. At this point it will return and stay at the set timing.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 VARI-CURVE CONTROL, PN 8983 The MSD Vari-Curve allows you to set an ignition curve for advance or to retard throughout the rpm range. The starting and ending rpm points of the curve are selected with rpm modules.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 TIMING CURVE EXAMPLES FOR AN ADVANCE CURVE FOR A RETARD CURVE First, you must set the mechanical timing to what will be the maximum amount of timing that the curve reaches. Install a ZERO module in the “Neg” jack and 15° module in the “Pos” jack. This will determine how much advance you want to add.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MULTI-FUNCTION IGNITION CONTROLLER, PN 8979, PN 8977 with BOOST RETARD The Multi-Function Ignition Controllers must be used with a single channel MSD Ignition Control such as a 6AL, 7AL-2, etc. The Controllers allow you to program and control a variety of timing and rpm options.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 Red Black Trigger Wires White Violet & Green (Magnetic Pickup Connector) Brown/White Cam Sync Lt Blue and Lt Green Fiber Optic Connection RPM Controls Yellow 2-Pin Plug Dark Blue Light Blue Orange/Yellow Retard Stages Pink Dark Brown Tan This wire is responsible for turning the MSD On and Off.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 PN 8977 AND PN 8979 FLOW CHART WITH HAND HELD MONITOR MENU TREE The following menu tree shows the different screens and programs of the Multi-Function Ignition Controls with the Hand Held Monitor. Menus Monitor List: 1 ScanTime 1Sec 2 CamSync NONE 3 Rpm 12500 4 RetSum 00.0 5 ShiftLt OFF 6 Gear 1 7 MaxCylDeg 0.0 8 Pressure12.50 9 BoostRet00.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD PROGRAMMABLE DIS-2, PN 6212 The Programmable DIS-2 Ignition Control is a programmable, high output ignition control designed for distributorless ignition systems.
www.msdignition.com email: msdtech@msdignition.com 4 - Pin Connector AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 Trigger Pickups White/Blue Black White (Coil 1) Green (Coil 2) 2 - Pin Connector Cam Sync Accessories 3-Step Rev Light Blue Dark Blue Tach Output Gray 3-Step Retard Pink Violet Tan Not Used - This wire has 12 volts and must be sealed.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 PN 6212 FLOW CHART WITH HAND HELD MONITOR MENU TREE The following menu tree shows the different screens and programs of the PN 6212 and Monitor. Monitor List: 1 ScanTime 1Sec 2 CamSync NONE 3 Rpm 12500 4 RetSum 00.0 5 LowBatt OK 6 ShiftLt OFF 7 Gear 1 8 RpmSw OFF 9 MaxCylDeg 0.0 10 Pressure 12.5 11 BoostRet 0.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 DIS-4 MULTI-CHANNEL PROGRAMMABLE BOOST CONTROLLER, PN 6562 WITH FUEL ADDER, PN 6563 The Multi-Channel Programmable Boost Controllers are designed to be used with the MSD DIS-4, PN 6215, or DIS-4HO, PN 62151, though it can also be used with MSD single channel ignitions (MSD 7AL-2).
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 PN 6563 AND PN 6562 FLOW CHART WITH HAND HELD MONITOR MENU TREE: The following menu tree shows the different screens of the Multi-Channel Programmable BTMs. Menus Monitor List: ScanTime 1Sec CamSync NONE Rpm 12500 RetSum 00.0 ShiftLt OFF Gear 1 MaxCylDeg 0.0 Fuel 0.0 (PN 6563 only) Pressure 12.75 BoostRet 0.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD MARINE IGNITION SYSTEM MSD offers several ignition components designed for marine applications; the MSD 6M-2 Ignition Control PN 6460, 7ML-2 Ignition Control PN 7250, Marine Rev Limiter PN 8768, Universal Marine Engine Protector PN 5468 and several Pro-Billet Distributors.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD MARINE IGNITION TO POINTS IGNITION SYSTEM RED IGNITION KEY TO 12V HEAVY RED TO BATTERY HEAVY BLACK TO BATTERY ORANGE BLACK + N BLACK GREEN (MAG-) CABLE HARNESS PN 64601 AUTOTRONIC CONTROLS CORPORATION PART NO. SERIAL NO..
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MARINE ENGINE PROTECTOR, PN 5468 The Marine Engine Protector is a universal rev limiter that can be used with inductive ignition controls. The rpm limit is adjusted with a potentiometer from 3,000 to 8,000 rpm. It can be used on 4, 6 and 8-cylinder automotive style engines. It cannot be used with an MSD Ignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 TACHOMETER INFORMATION This section is designed to aid you in the installation of any aftermarket, or factory tachometer.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 TACHOMETER INFORMATION Tachometer Trigger Wire This diagram shows a typical wiring schematic for aftermarket tachometers. These tachometers will usually have three wires and sometimes a fourth for a panel light. The tach trigger wire is the wire that originally went from the Tachometer to the Negative side of the coil.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 TACHOMETER INFORMATION Note #3 GM Inline Filters Many General Motors Corporation vehicles have an in-line filter that should be bypassed when the factory tachometer drops back to zero as the engine RPM is increasing. The drawings at the right show what the filter might look like.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD TACH ADAPTER PN 8910 TO VOLTAGE TRIGGERED TACH FROM IGNITION KEY PN 8910 INDICATES CONNECTION TO BATTERY D RE HEAVY BLACK TO BATTERY TACH OUTPUT WHITE HEAVY RED + MAGNETIC CONNECTOR NOT USED RED Multiple Spark Discharge GE N RA O TM N IGNITIO + AUTOTRONIC CONTROLS CORPORATION PART NO. SERIAL NO..
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD TACH ADAPTER PN 8912 The PN 8912 is a dual channel adapter that will only be used with MSD line of DIS-2 or DIS-4 Ignition (the DIS-4 requires two). The Adapter has six wires that need to be connected and the DIS Ignition already have the matching connectors.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD IGNITION TESTER, PN 8998 MSD’s Ignition Tester, PN 8998, will give you a quick way to confirm the operation of your MSD Ignition and Coil. It will also let you check rev limits, rpm switches and the camshaft sync signal of controls with Individual Cylinder Management circuits.
www.msdignition.com email: msdtech@msdignition.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD IGNITION TESTER TO MSD 7 SERIES IGNITION WITH TIMING CONTROL Note: The Obsoleted PN 8995 Tester will not work through the magnetic pickup of a timing control.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 MSD IGNITION TESTERS, PN 8996 The Multi-Channel Ignition Testers, PN 8996, can check the channels of the MSD DIS Ignition Controls. It connects easily and will simulate a trigger signal through the four (if used) trigger wires. A test plug is supplied that connects to the spark plug wires and ground.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 TROUBLESHOOTING MSD Spark Plug Wires If you suspect a spark plug wire to be open, or the cause for poor engine performance, the resistance of each wire can be checked. This will tell you two things: 1. That there is continuity (plug wire is not open). 2. That there is too much resistance in the wire.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 HOW TO TEST AN MSD SERIES IGNITION CONTROL If for some reason you feel that you have a non-functioning MSD Ignition Control, this simple test can be performed to determine if the MSD Ignition Control is functioning properly. If triggering the MSD using the magnetic pickup connector (Violet and Green Wire) of the MSD: A. B. C. D.
www.msdignition.com email: msdtech@msdignition.com AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344 RECOMENDATION FORM NOTE: Technical information is available by mail, phone or the internet. Telephone: (915) 855-7123, Fax: (915) 857-3344 8 a.m. - 5 p.m. Mountain Standard Time MSD Ignition 1490 Henry Brennan Dr. El Paso, Texas 79936 Attn: Customer Service Dept. E-mail: msdtech@msdignition.
AUTOTRONIC CONTROLS CORPORATION 1490 HENRY BRENNAN DR., EL PASO, TX 79936 (915) 857-5200 FAX (915) 857-3344 PN 9615 PRINTED IN U.S.