Eiconcard C9x Family for PCI-Compatible Bus www.eicon.
First Edition (July 2001) 203-226-01 Eicon, Eiconcard, and the Eicon logo are either trademarks or registered trademarks of Eicon Networks Corporation. Changes are periodically made to the information herein; these changes will be incorporated into new editions of the publication. Eicon Networks may make improvements and/or changes in the products and/or programs described in this publication at any time. Copyright © 1996-2001 Eicon Networks Corporation.
Table of Contents Introduction ................................................................... 5 About this Manual ....................................................................... 5 Installing the Eiconcard C9x.......................................... 6 Making an ISDN Connection......................................... 8 Termination ............................................................................... 11 Making a V.24 Connection ..........................................
www.eicon.
Introduction The Eiconcard C9x is a PCI Plug-and-Play (PnP) card that offers X.25 connectivity through a V.24 serial port at speeds of up to 64 Kbps, and/or through an ISDN BRI port (Eiconcard C91) at speeds of up to 128 Kbps (over the “D” channel or the “B” channels). The Eiconcard C9x is typically used for stand-alone or remote LAN gateways. Note The Eiconcard C9x also supports protocols such as SDLC, PPP, and Frame Relay.
Installing the Eiconcard C9x Follow the steps below to install the Eiconcard C9x. If you want the Eiconcard C9x to be available to multiple users on a LAN, install it in the PC that will function as a gateway for the LAN. 1 Prepare the PC Turn off the PC and disconnect its power cable. Remove the cover of the PC according to the instructions that came with it. 2 Install the Eiconcard C9x Drain static electricity from your body by touching the metal chassis (the unpainted metal at the back of your PC).
screw PCI Eiconcard PCI slot Figure 2. Inserting the Eiconcard C9x. Fasten the adapter with the screw (to ensure that the adapter is properly secured and grounded to the PC’s chassis). f) Replace the cover of your PC as described in your PC’s manual. g) Reconnect the power cable. e) 3 Test the Eiconcard C9x The application software purchased with the Eiconcard C9x contains a test program to verify the card’s integrity. Consult the documentation supplied with this software for details.
Making an ISDN Connection Note Only the Eiconcard C91 supports ISDN connections. After you have installed your Eiconcard C91, connect your ISDN line. In Europe and most countries worldwide In Europe as well as most countries outside of North America and Japan, your Eiconcard C91 adapter can be connected directly to your ISDN line using the included cable. 1. ISDN wall jack Eiconcard C91 3. 2. Figure 3. Connecting the ISDN cable. 1 Take the cable included with the Eiconcard C91.
Eiconcard C91 U-interface: If your Eiconcard C91 has a U-interface, the NT1 is integrated into the adapter, and you do not need a separate NT1. 1. ISDN wall jack Eiconcard C91 3. 2. Figure 4. Connecting the ISDN cable. 1 Take the cable included with the Eiconcard C91. 2 Plug the RJ-45 end into the Eiconcard C91. 3 Plug the RJ-11 end into the ISDN wall jack. Note In North America, many ISDN wall jacks (with a U-interface) are RJ-11.
Eiconcard C91 S/T-interface: If your Eiconcard C91 has an S/T-interface, you need a separate NT1. Note You can order an NT1 from Eicon Networks or from another supplier. Eiconcard C91 ISDN wall jack 2. 4. 1. 3. 6. NT1 S/T jack U jack Figure 5. Connecting to an NT1. 1 Take the cable included with the Eiconcard C91. 2 Plug one end into the Eiconcard C91. 3 Plug the other end into the NT1’s S/T jack. 4 Take the cable included with the NT1. 5 Plug one end into the ISDN wall jack.
Termination This section applies to S/T interface users in Australia and North America, and provides instructions to help set up termination scenarios. Termination requirements vary according to: the number of devices connected to the NT1; and the distance between the devices and the NT1. For users who require termination, the Eiconcard C91 S/T has been shipped with a separate terminating resistor.
Multiple ISDN Devices If the NT1 is connected to more than one ISDN device, follow the procedures below. 75 meters or more If the connection spans 75 meters (250 feet) or more, both end devices on the ISDN bus must be set to 100 ohm termination. If the Eiconcard is one of the end devices, connect the 100 ohm terminating resistor included with the ISDN cable. Consult the manuals provided with the other ISDN devices and NT1 for more details.
Making a V.24 Connection The Eiconcard C91 can make V.24 connections using standard V.24 cables. Connection Cables Required Eiconcard C91 to V.24 DCE V.24 DCE Cable Part # 300-007 Eiconcard C91 to V.24 DTE V.24 Null Modem Cable, or 300-022 V.24 Null Modem Cable (gender-changed) 300-048 Table 1. Standard Interface Cables Interface Specifications The standards compliant with the V.24 interface are listed in Table 2. Standard Compatibility CCITT V.24 Signaling CCITT V.28 Electrical CCITT X.
The V.24 DCE Interface A pin-out diagram for the V.24 DCE interface is shown in Figure 6. The signal definitions and names are listed in Table 3. 1 PG N D TXD RXD RTS CTS DSR SG N D DCD 14 TCLK RCLK TEST DTR RLB RI DTECLK TI 25 13 Figure 6. V.
LED Functionality Note The Eiconcard C90 only has the V.24 port, the Eiconcard C91 has both the ISDN BRI port and V.24 port. ISDN (Eiconcard C91 only) D-channel Status The D-channel controls the link to your ISDN service provider. Off ..........The line is not active. The cable may not be connected. Blinking .. The line is active, but a link can’t be established. This may be a symptom of incorrect configuration. Steady.... The ISDN line is active and operating normally.
Technical Specifications Technical Data • PCI bus compatible (32-bit slot) Eiconcard CPU/Memory/Flash # of HSI Ports #of ISDN BRI Ports Eiconcard C90 15.36 MHz Motorola 68302 512 KB RAM / 512 KB Flash 1 N/A Eiconcard C91 15.36 MHz Motorola 68302 512 KB RAM / 512 KB Flash 1 1 Hardware Installation • Automatic configuration of interrupt request level setting and I/O address • 32-bit I/O access External Interface Eiconcard External Interface Eiconcard C90 One DB-25 female port.
International Regulatory Information Regulatory Information for the USA: WARNING. Changes or modifications to this unit not expressly approved by Eicon Networks Corporation could void the user's authority to operate the equipment.
FCC Part 68 Notice This unit complies with Part 68 of the FCC rules. On the bottom of this equipment is a label that contains, among other information, the FCC registration number. If requested, this information must be provided to the telephone company. An FCC compliant telephone cord and modular plug is provided with this equipment, designed to be connected to the telephone network or premises wiring using a compatible modular jack which is Part 68 compliant.
Regulatory Information for Canada NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. Industry Canada does not guarantee the equipment will operate to the user’s satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company.
Regulatory Information for Europe EU Declaration of Conformity EN: Eicon Networks Corporation declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive1999/5/EC. DE: Eicon Networks Corporation erklärt, daß diese Telekommunikations-endeinrichtung den grundlegenden Anforderungen und anderen relevanten Bestimmungen der Richtlinie 1999/5/EG entspricht.
Safety Status: SELV No voltages within this equipment exceed SELV voltages. All interconnection points and ports are SELV. User/Installer Instructions for the United Kingdom Important Safety Considerations When Installing Into A Host Computer System The Eiconcard C9x is a single PCI card.
Regulatory information for Australia • This customer equipment shall only be installed in a PC that requires the use of a tool to gain access to internal parts (e.g. this customer equipment must not be installed in a PC with a ‘flip lid’). • Proper installation of the Eiconcard C9x card requires that it is screwed to the metal backplate of the computer. This ensures proper grounding, which is necessary for safety purposes.
203-226-01
