Table of Contents 1. Introduction ···················································································· 2 2. Features ··························································································· 2 3. Operation notice ··········································································· 3 4. Projector figure ············································································· 4 4.1 Function list of control panel 4 5.
1.Introduction Please read this manual carefully before using, to find out: • How to use the projector safely • How to use the remote control • How to set up and connect the projector • How to start and turn off the projector • How to use the On-screen display (OSD) menus • How to replace the lamp module • How to solve troubleshoot common problems 2.Features • • • • • • • • • • Use the technology of chip TI 0.7”/ 0.6” DLPTM. Full-function remote including mouse controls. High quality manual zoom lens.
3.Operation notice: Please read and follow the following safety instructions and description carefully. Inappropriate operation method may result in fire, electrical shock, and personal injury or shorten the life span of projector. Warning: Do not cover the lens while the lamp lights up. Warning: To protect your eyes, do not look directly into the projector’s light source. Warning: Make sure that you provide adequate ventilation for the projector.
4.Projector figure Control panel Infrared remote sensor Zoom ring Focus ring Lens Cap 4.
Power LED (Indicator light) • When the projector is on, Power LED will blink. Press “Power” button to enter screen, Power LED remains lit continually. Temp LED (Indicator light) • • When fan malfunctions, the screen will shows the message stating “fan error, system is forced to turn off!”. Temp LED remains lit continually. When the temperature is unusual, screen will shows the message stating “temperature error, system is forced to turn off!”. Temp LED blinks once every half of second.
ÇÈ (Up and down button) • OSD active: Press to move between menu options. • OSD inactive: Press to select the video input source. ÅÆ(Left and right button) • When using these buttons, press ”Auto/Enter” button then press right key to add setting value; on the contrary, left button to reduce the setting value.
5.Accessories You should check to make sure the accessories below are complete with nothing missing. For any missing accessory, please contact the local distributor.
5.1 Remote Control The infrared sensor is located on the top of the projector. The distance between the sensor and remote control should not exceed 10 meters for the remote control to function correctly. How to insert batteries in the remote control: 1) Remove the battery compartment cover. 2) Insert two AAA batteries into the battery compartment. Ensure the batteries polarity is aligned correctly. 3) Replace the battery compartment cover.
5.2Function list of remote control panel: Function key Function description Freeze/Esc/L • Enter/R • • • Power • • Mode • • • Menu Source • • Blank • Auto • Pg.Up • • • • Pg.Dn OSD inactive: press this button to freeze the display image. Press again to resume motion. OSD active: press this button to exit. Mouse active: Use as the left mouse button. During common status or using OSD options, please refer to “Auto/Enter” of “Projector panel” in page 5.
• Press this button, then press right and left button to execute keystone correction. • Press button to correct a display image that is wider at the bottom. • Press button to correct a display image that is wider at the top.(*) • Do not activate when displaying text or spreadsheets to eliminate text distortion. • OSD inactive: The same as the Up, Down, Left, Right control button on the panel. (*) • Mouse active: Use as the Up, Down, Left, Right button of mouse.
6.Operation guide 6.1 Connecting components You can connect the projector to your computer, DVD player or VCR. To connect the projector to a DVD player or VCR, go to “Connecting to a DVD player or VCR” on page 12. 1. 2. 3. 4. 5. 6.
6.2 How to connect the projector to your computer 1) Plug the VGA cable into the VGA port at the left side of projector, then plug the other end of VGA cable into the computer. Note: If you are connecting to a notebook, you may need to make adjustments to the notebook’s display settings first. Please refer to the user’s guide that came with your notebook.
After you have connected all components to the projector, you are ready to begin using the projector. 6.4 Turning on the projector: 1) Remove the lens cap. 2) Ensure the cable connectors have connected properly. 3) Plug the power cord, press the main switch on the top of power cord socket of the projector, Power LED blinks steadily and slowly. 4) Press down the “Power” button on the remote control or panel to turn on the projector, the Power LED displays steady green.
6.6 Turning off the projector 1) Press “Power” button to turn off the projector lamp. 2) When you press the “Power ” button, you will see the message stating “Press Power again to turn off the lamp!”. At this time, you only have to press “Power” button again to turn off the projector. Or else the message will disappear automatically after 5 sec. 3) After the lamp is turned off, LED indicator will blink rapidly. At this time, “Power” will have no function.
To lower the projector 1. Press and hold the Adjustor-foot release button. 2. Lower the projector to the height you want, then release the button to lock the foot into position. 6.8 Adjusting the image focus and zoom Zoom Wheel Focus ring You can adjust the zoom ring to magnify or minify the image. Rotate counterclockwise to magnify the image. Rotate clockwise to minify the image. To adjust the focus, please rotate the focus ring to obtain the best focus. The focus distance of this projector is 1.
7.OSD Menu Press “Menu” button to open the menu. Press up and down button to choose the OSD options or press Esc to exit. To enter the submenu, please press “Auto/Enter” button or right button. Under the submenu, press “Menu” or the Esc button on the remote control to return to Menu main screen or double click to exit the OSD menu. 7.
7.2 Image (Video mode) Submenu Description options Brightness Adjusts the brightness of the Operation method • display image. • Contrast Adjusts the contrast of the display image. • • Hue Adjusts the balance between red and green color levels. • • Saturation Changes the display image • from black and white to color. • Sharpness Adjusts the sharpness of the display image.. • • Press button can reduce the brightness of display image. Press button can increase the brightness of display image.
7.3 Display (Computer mode) Submenu options Description Minimizes any vertical bars • Frequency Phase V position or stripes visible on the screen background. Removes any horizontal distortion and clears or sharpens the displayed characters. Adjusts the display image up and down. • Press Å Æ button to adjust(*). • PressÅ button to move down the display image. PressÆ button to move up the display image.(*) • H position Adjusts the display image left and right.
Proportion User color Red Gain Switches between a display • image mode of 4:3 or 16:9. Activates individual red, • green, or blue color correction controls. • Customizes the red color levels. • • Green Gain Customizes the green color • levels. • Blue Gain Customizes the blue color levels. • • Color temperature Increases the red or blue • tint of the display image. • * Press “Auto” button to return to previous setting. 19 Press Å Æ button to choose.
7.4 Display (Video mode) Submenu options Description Corrects a display image Keystone Operation method • that is wider at the top or at the bottom. • To choose the screen • image proportion 16:9 or 4:3. Press “Auto” button to return to previous setting. Proportion * 20 Press button to correct the display image that is wider at the bottom. Press button to correct the display image that is wider at the top.(*) Press button to choose.
7.5 Audio Submenu options • Volume Description or operation method Press button to decrease the volume. Press button to increase the volume.(*) Press button to decrease the volume of the left Balance speaker. • Press button to increase the volume of the right speaker.(*) • Press button to decrease the treble Treble • Press button to increase the treble.(*) To adjust the low frequency of the sound source. Bass • Press button to weaken the bass. • Press button to enhance the bass.
7.6 Management Submenu Description options OSD location Adjusts the position of the OSD Operation method • within the display image. Projection (Projection before the screen) • Default Press button to select (*). Press button to select (*). (Projection behind the screen) Flips the display image so it can be viewed correctly when the projector is set up for rear screen projection.
Lamp Reset Resets the lamp timer after replacing the lamp module. • Auto Adjust Automatically adjusts the display image to the ideal settings for the display source. • • Returns all settings to the factory • defaults. Source type Switches between available vide • input sources. * Press “Auto” button to return to previous setting. Reset All 23 Press right button, then it will display the message stating “Press Auto/Enter button, reset the lamp timer” to confirm that the user has replaced the lamp.
7.7 Language Changes the language of the OSD menu. Choose between English, German, French, Italian, Spanish, Portuguese, Japanese, Traditional, Chinese, and Simple Chinese.
8. Maintenance and service Change the module lamp immediately when the lamp life reaches 1500 hrs to maintain the best projection image. 8.1 Replacing the lamp module When the lamp is within 30 hours of maximum lamp life, projector will display a warning automatically stating, “Lamp has reached its end of life! Lamp replacement is suggested!”. When this message appears, please change the lamp immediately. To replace the lamp module: 1. Turn off the projector and wait for the fan to stop. 2.
8.2 Cleaning the projector lens Please follow the following procedures to clean the projector lens: 1 Pour out a little cleaner on a clean soft cloth. Do not use the cleaner with particle, the cleaner that contains solvent or other chemicals of poor quality, they may cause damage to the projector lens. 2 Use the soft cloth to wipe the projector lens lightly according to the direction of a certain circling motion. 3 After finish wiping, place the lens cap on when the projector is not being used.
9. Appendix 9.1 Common problems and solutions When you encounter problems while using the projector, please refer to the following contents: If the suggestions in the troubleshooting section does not correct the problem, please contact the local distributor or our customer service center. No picture on the screen ÖMake sure that all components are connected correctly and securely in accordance to the connection method and line that is introduced in the previous chapter.
The focus of display image is blurred ÖAdjust the focus ring on the projector. ÖMake sure the projection screen is 1.4 ~12 meters from the projector. Projected colors don’t match the computer or video player’s colors ÖThis is a normal phenomenon; just adjust the brightness, color or contrast value in the menu. When projector is connected to DVD, and the film aspect ratio is 16:9, the display image is distorted. ÖPlease adjust the image proportion of projector into 4:3.
9.2 The distance proportion between screen and projector (Based on Zoom Ratio 1.18:1, for reference only) Projection distance 1.
9.3 Specifications EIP-25 Model No. Resolution XGA(1024*768), SXGA(1280*1024) compressed Lamp 250W User Replaceable VIP Lamp Brightness 2500 Lumens Dimensions 330 x 276 x 104 mm Weight 7.5 lbs Projection distance Ratio of projection screen and distance Zoom ratio 1.4m--12m Uniformity 80% Screen proportion 4:3 / 16:9 screen selectable Contrast ratio 1800 : 1 H. Frequency 31.5 -- 80 kHz V.
