Media Card Imager Kit MODEL EVW-100 INSTALLATION AND OPERATION OF THE IMAGER BOX This Media Card Imager kit is an optional kit to project image data in various format and files created with Microsoft PowerPoint with our projector. Image data can be easily projected just by attaching the Imager Box to a projector without any connection with a computer. This kit is only used for our projectors that have a terminal for the Imager Box.
Compliances Federal Communication Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generated, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Table of Contents 3 Contents of Media Card Imager Kit 3 Name of Each Part of Imager Box 4 Attach Imager Box to Projector 5 Remove Imager Box from Projector 6 Load and Remove CF Card 6 Use CF Card Adapter 7 Handle CF Card and Adapter 8 Specifications 9 PLAY BACK IMAGE (OPERATING PROJECTOR) 11 PLAYING BACK IMAGE IN THE MEMORY CARD 11 PICTURE IMAGE ADJUSTMENT 15 PICTURE SIZE ADJUSTMENT 17 Contents of Media Card Imager Kit Imager Box Media Card Imager Kit Owner's Man
Name of Each Part of Imager Box Imager Box INDICATOR LATCH BUTTON (lights while accessing) CF CARD SLOT CF CARD EJECT BUTTON CONNECTOR PLUG SWITCH BUTTON MOUNTING HOOK 4
Attach Imager Box to Projector CAUTION : Turn off the projector when attaching the Imager Box to the projector. Do not attach or remove while the projector is turned on. It may damage the equipment. 1 Remove 4 covers attached to a projector. Insert the MOUNTING HOOKs (A) into the projector to the arrow direction. (Fig.-1) 2 Plug the CONNECTOR PLUG into the DVI Terminal of the projector while pressing the Imager Box LATCH BUTTON, and release it. (Fig.-1) cover Remove 4 covers.
Remove Imager Box from Projector CAUTION : Do not remove the Imager Box from the projector while the projector is on. It may damage data in a memory card and the card itself. CAUTION :Removing by force may damage the Imager Box. Press the LATCH BUTTON to the arrow direction. Then pull and remove the Imager Box. (Fig.-3) Press the LATCH BUTTON. Pull and remove the Imager Box. Load and Remove CF Card Load CF Card Insert the CF Card into the CF Card slot of the Imager Box until the EJECT BUTTON pops out.
Use CF Card Adapter CF Card Adapter is used when a CF Card is loaded into the PC card slot of a computer. You can write and rewrite data into the CF Card with the Adapter through the PC card slot of a computer. For operation, refer to the "Media Card Imager" Owner's Manual. Attach CF Card Insert the CF Card firmly into the CF Card Adapter, aligning the arrows on the CF Card and the adapter. Insert the CF Card aligning the arrows. Remove CF Card Pull the CF Card straight out.
Handle CF Card and Adapter ● CF Cards / Adapters are high-precision electronic devices. Do not bend, drop, apply strong forces or shock or place it where a strong static electrical charge may be generated. ● Do not touch the surface of the contact area with your fingers or allow it to be stained with foreign materials. ● Do not attempt to disassemble or alter CF Cards. ● Moving CF Card rapidly between hot and cold temperatures may cause condensation (water droplets) to form on it, leading to malfunctions.
Specifications ■ Imager Box Dimensions (W x H x D) 4.61" x 2.76" x 0.75" (117mm x 70mm x 19mm) (not including MOUNTING HOOKs) Weight 5.29 oz (150g) Operating Voltage DC 5V 450mA, DC 3.3V 600mA Available Memory Card We recommend you to use a CF card that comes with this kit. The following memory cards can also be used. • Microdrive (lower than 1GB) We do not guarantee use of any memory card except for the above. Some memory cards may not operate properly.
IMAGE PLAYBACK (OPERATING PROJECTOR) PLAYING BACK IMAGE IN THE MEMORY CARD 1 Attach Imager Box to your projector properly (P5), and turn the projector on. Refer to Owner’s Manual of your projector for operation. 2 3 Load a memory card into CF Card Slot of Imager Box. (P6) Projector automatically turns to MCI mode and shows the image data in a memory card. NOTE ; Refer to Owner’s Manual of your projector for location of each button and basic operation. MENU BAR Press MENU button while in MCI mode.
IMAGE PLAYBACK (OPERATING PROJECTOR) SELECTING INPUT SOURCE When a memory card is loaded into Imager Box connected to the projector, MCI mode is automatically selected. The first Page of the latest Index in a memory card is displayed on a screen. To switch to MCI mode manually, operate as follows. DIRECT OPERATION INPUT button Choose Computer by pressing INPUT button on Top Control or on Remote Control Unit. If projector cannot reproduce proper image, select correct input source through MENU OPERATION.
IMAGE PLAYBACK (OPERATING PROJECTOR) To project desirable image, select Index and then Page as follows. SELECTING INDEX 1 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to VIEW Menu icon. 2 Press POINT DOWN button to move a red frame pointer to Index icon and then press SELECT button. The table of Indexes in the memory card is displayed. Press RIGHT CLICK button on Remote Control Unit to stop table display.
IMAGE PLAYBACK (OPERATING PROJECTOR) AUTO PLAY FUNCTION 1 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to VIEW Menu icon. 2 Press POINT DOWN button to move a red frame pointer to Auto play icon and then press SELECT button. Auto play setting dialog box will appear VIEW MENU VIEW Menu icon 3 On When setting Auto play function on, move a red arrow pointer to “On,” adjust interval (sec.
IMAGE PLAYBACK (OPERATING PROJECTOR) PICTURE IMAGE ADJUSTMENTS IMAGE LEVEL SELECT (DIRECT OPERATION) Select Image Level among Standard, Real, Image 1, Image 2, Image 3 and Image 4 by pressing IMAGE button on Top Control or on Remote Control Unit. IMAGE button Standard Real Standard Normal picture level preset on this projector. Real Picture level with improved halftone for graphics. Image 1 ~ 4 User preset picture adjustment in IMAGE ADJUST Menu (refer to P16).
IMAGE PLAYBACK (OPERATING PROJECTOR) IMAGE LEVEL ADJUSTMENT 1 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to IMAGE ADJUST Menu icon. 2 Press POINT DOWN button to move a red frame pointer to the item that you want to adjust, and then press SELECT button. The level of each item is displayed. Adjust each item by pressing POINT LEFT/RIGHT buttons.
IMAGE PLAYBACK (OPERATING PROJECTOR) PICTURE SIZE ADJUSTMENT This projector has a picture screen resize function, which enables you to display the desirable image size. 1 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to SCREEN Menu icon. 2 Press POINT DOWN button and move a red frame pointer to the function that you want to select and then press SELECT button.