MULTIMEDIA PROJECTOR MODEL LC-XB22 OWNER’S MANUAL
Features and Design This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology. ◆ Compact Design ◆ Brightness of the projection lamp can be selected in the Setting menu. (See page 42.) This projector is designed compact in size and weight. It is easy to carry and work anywhere you wish to use.
Table of Contents Features and Design . . . . . . . . . . . . . . . . . . .2 Table of Contents . . . . . . . . . . . . . . . . . . . . . .3 To the Owner . . . . . . . . . . . . . . . . . . . . . . . . .4 Safety Instructions . . . . . . . . . . . . . . . . . . . .5 Computer Input . . . . . . . . . . . . . . . . . . . . .
To the Owner Before operating this projector, read this manual thoroughly to operate the projector properly. This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.
Safety Instructions All the safety and operating instructions shoule be read before the product is operated. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. This projector should be operated only from the type of power source indicated on the marking label.
Safety Instructions Air Circulation Installing the Projector in Proper Position Openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. Install the projector properly. Improper Installation may reduce the lamp life and cause a fire hazard. 20˚ Do not tilt the projector more than 20 degrees from side to side. CAUTION 20˚ Hot air is exhausted from the exhaust vent.
Compliance Federal Communication Commission Notice Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Part Names and Functions Front q w e r t y u q Back w ert !6 y i Power Cord Connector Infrared Remote Receiver Zoom Lever Focus Ring Projection Lens Lens Cover (See page 46 for attaching.) Air Intake Vent u o !0 i Top Controls and Indicators o Air Intake Vent !0 Terminals and Connectors !1 Speaker !6 Exhaust Vent CAUTION !1 Bottom !2 !3 Hot air is exhausted from the exhaust vent. Do not put heat-sensitive objects near this side.
Part Names and Functions Part Names and Functions Rear Terminal q w e r t AUDIO IN R L (MONO) VIDEO COMPUTER IN 1 / COMPONENT IN ✽ SERVICE PORT S-VIDEO y USB COMPUTER / COMPONENT RESET AUDIO IN AUDIO OUT COMPUTER IN 2 / MONITOR OUT (VARIABLE) o q COMPUTER IN 1/ COMPONENT IN Connect output signal from a computer (Analog RGB) or video equipment (Component or RGB Scart) to this terminal. Optional cables are required when using this terminal as component input or RGB Scart 21-Pin Video input.
Part Names and Functions Top Control q w e r t y ON - OFF POWER INPUT SELECT VOLUME + KEYSTONE VOLUME – WARNING LAMP REPLACE MENU o q KEYSTONE button Correct keystone distortion. (p22, 39) w INPUT button Select input source. (p24, 32, 33 ) e POWER ON–OFF button Turn the projector on or off. (p18, 19) r SELECT button Execute the item selected. It is also used to expand/ compress the image in Digital zoom +/– mode.
Part Names and Functions Part Names and Functions Remote Control q SIGNAL EMISSION indicator This indicator lights red while the laser beam is being emitted from the laser light window or a signal is being sent from the remote control to the projector. w COMPUTER button Select the input source (COMPUTER 1 or COMPUTER 2). (p24, 33) ed) button e D.ZOOM (e Select the Digital zoom +/– mode and resize the image. (p31) ed7 8) buttons r POINT (e q Select an item or adjust the value in the On-Screen Menu.
Part Names and Functions Laser Pointer Function This remote control emits a laser beam from the laser light window. With the LASER button pressed, laser light goes on. The signal emission indicator lights red and laser is emitted with red light. With the LASER button pressed for more than 1 minute or released, the light goes off. To lock this function, press both the MENU button and the NO SHOW button for more than 10 seconds.
Installation Positioning the Projector This projector is designed to project on a flat projection surface and can be focused from 3.3’(1.0m) - 25.3’(7.7m). Refer to the figure and the table below for the screen size and the distance between the projector and the screen. A:B = 9:1 25.3' (7.7m) (Inch Diagonal) 300” Max. Zoom 16.4' (5.0m) 12.5' (3.8m) 195” Min. Zoom 195” 8.2' (2.5m) 150” 100” 40” A 127” Installation 3.3' (1.
Installation Connecting the AC Power Cord This projector uses nominal input voltages of 100-120 V or 200-240 V AC. This projector automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce risk of electrical shock, do not plug into any other type of power system. Consult your authorized dealer or service station if you are not sure of the type of power being supplied.
Installation Connecting to a Computer Cables used for connection • VGA Cable (Mini D-sub 15 pin) (Only one cable is supplied.) • USB Cable ✽ • Audio Cables (Mini Plug: stereo) ✽ (✽ = Not supplied with this projector.
Installation Connecting to Video Equipment Cables used for connection • Video and Audio Cable (RCA x 3) ✽ • S-VIDEO Cable ✽ • Audio Cable (Mini Plug: stereo) ✽ (✽ = Not supplied with this projector.
Installation Connecting to Component Video Equipment Cables used for connection • Audio Cable (Mini Plug (stereo) x 2 or RCA x 2) ✽ • Scart-VGA Cable ✽ • Video and audio cable✽ • Component-VGA Cable ✽ (✽ = Not supplied with this projector.
Basic Operation Turning On the Projector 1 Complete peripheral connections (with a computer, VCR, etc.) before turning on the projector. 2 Connect the projector's AC power cord into an AC outlet. The POWER indicator blinks red in a moment and lights red. 3 Press the POWER ON-OFF button on the top control or on the remote control. The POWER indicator turns green lighting and the cooling fans start to operate. The preparation display appears on the screen and the count down starts.
Basic Operation Turning Off the Projector 1 Press the POWER ON-OFF button on the top control or on the remote control, and a message "Power off?" appears on the screen. 2 Press the POWER ON-OFF button again to turn off the projector. The POWER indicator starts to blink red, and it continues while the cooling fans are operating for about 90 seconds. (About 120 seconds when the fan mode is L2. See page 44.) 3 The message disappears after 4 seconds.
Basic Operation How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Menu. Refer to the following pages regarding each adjustment and setting procedure. On-Screen Menu Menu icon 1 Press the MENU button to display the On-Screen Menu. 2 Press the Point 7 8 buttons to select a Menu icon to adjust. Press the Point ed buttons to select an item to adjust. Pointer (red frame) Press the Point d button to move the pointer. 3 Press the SELECT button to show the item data.
Basic Operation Menu Bar For computer source Guide Window PC System Menu Image Select Menu Screen Menu Setting Menu Shows the selected Menu of the OnScreen Menu. Used to select computer system. (p25) Used to select an image level among Standard, Real, Blackboard(Green), and Image 1 ~ 4. (p29) Used to adjust size of image. [Normal / True / Wide / Digital zoom +/–] (p31) Used to change settings of the projector or reset lamp replace counter.
Basic Operation Zoom and Focus Adjustment Rotate the Zoom Lever to zoom in and out. Rotate the Focus Ring to adjust the projected picture focus. Zoom Lever Focus Ring Keystone Adjustment If a projected picture has keystone distortion, correct the image with Keystone adjustment. 1 Press the KEYSTONE button on the top control or on the remote control, or select Keystone in the Setting Menu (p41). The keystone dialog box appears. 2 Correct keystone distortion by pressing the Point ed buttons.
Basic Operation No Show Function Press the NO SHOW button on the remote control to black out the image. To restore to normal, press the NO SHOW button again or press any other button. When a projected image is captured and set as “User” in the Logo item in the Setting Menu (p40), the screen changes each time you press the NO SHOW button as follows. black out ➜ the captured image ➜ normal ➜ • • • • • The message disappears after 4 seconds. P-Timer Function Press the P-TIMER button on the remote control.
Computer Input Input Source Selection Direct Operation Choose either Computer 1 or Computer 2 by pressing the INPUT button on the top control or press the COMPUTER button on the remote control. Before using these buttons, correct input source should be selected through menu operation as described below. INPUT button Computer 1 Computer 2 ✳ Video COMPUTER button Computer 1 Computer 2 ✳ ✳ See Note at the bottom of this page.
Computer Input Computer System Selection This projector automatically tunes to various types of computers based on VGA, SVGA, XGA or SXGA with its Multi-scan system and Auto PC Adjustment. If Computer is selected as a signal source, this projector automatically detects the signal format and tunes to project a proper image without any additional setting. (Signal formats provided in this projector is shown on page 55 ) ✔Note: The projector may display one of the following messages.
Computer Input Auto PC Adjustment Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal, and Vertical to conform to your computer. Auto PC Adjustment function can be operated as follows. Auto PC Adj. 1 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red frame pointer to PC Adjust Menu icon. 2 Press the Point d button to move the red frame pointer to Auto PC Adj. icon and then press the SELECT button twice.
Computer Input Manual PC Adjustment Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector. Manual PC Adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has 5 independent memory areas to memorize those parameters manually adjusted. It allows you to recall the setting for a specific computer. PC Adjust Menu icon 1 Press the MENU button to display the On-Screen Menu.
Computer Input Display area Select the resolution at the Display area dialog box. Press the SELECT button at the Display area icon and the Display area dialog box appears. Display area H Adjust the horizontal area displayed by this projector. Press the Point 7 8 buttons to decrease/increase value and then press the SELECT button. Display area Display area V Adjust the vertical area displayed by this projector. Press the Point 7 8 buttons to decrease/increase value and then press the SELECT button.
Computer Input Image Level Selection Direct Operation Select an image level among Standard, Real, Blackboard(Green), Image 1, Image 2, Image 3, and Image 4 by pressing the IMAGE button on the remote control. IMAGE button Standard Real Standard Normal picture level preset on this projector. Blackboard(Green) Real Picture level with improved halftone for graphics. Image 1 Image 2 Blackboard(Green) Picture level suitable for the image projected on a blackboard.
Computer Input Image Level Adjustment 1 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red frame pointer to the Image Adjust Menu icon. 2 Press the Point d button to move the red frame pointer to the item that you want to adjust, and then press the SELECT button. The level of each item is displayed. Adjust each level by pressing the Point 7 8 buttons.
Computer Input Screen Size Adjustment This projector has the picture screen resize function, which enables you to customize the image size. 1 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red frame pointer to the Screen Menu icon. 2 Press the Point d button and move the red frame pointer to the function that you want to select and then press the SELECT button. Screen Menu Screen Menu icon Move the red frame to the function and press the SELECT button.
Video Input Input Source Selection (Video, S-Video) INPUT button Direct Operation Video Choose Video by pressing the INPUT button on the top control or the VIDEO button on the remote control. Before using these buttons, correct input source should be selected through menu operation as described below. Computer 1 Computer 2 ✳ VIDEO button Video ✳ See Note at the bottom of this page. Input Menu icon Menu Operation 1 Press the MENU button to display the On-Screen Menu.
Video Input Input Source Selection (Component, RGB Scart 21-Pin) Direct Operation INPUT button Computer 1 Choose Computer 1 by pressing the INPUT button on the top control or press the COMPUTER button on the remote control. Before using these buttons, correct input source should be selected through menu operation as described below. Computer 2 ✳ Video COMPUTER button Computer 1 Computer 2 ✳ ✳ See Note at the bottom of this page.
Video Input Video System Selection 1 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red frame pointer to the AV System Menu icon. 2 Press the Point d button to move the red arrow pointer to the system that you want to select and then press the SELECT button. Video or S-Video Auto The projector automatically detects incoming video system, and adjusts itself to optimize its performance. When Video System is PAL-M or PAL-N, select system manually.
Video Input Image Level Selection Direct Operation IMAGE button Standard Select a desired image level among Standard, Cinema, Blackboard (Green), Image 1, Image 2, Image 3, and Image 4 by pressing the IMAGE button on the remote control. Standard Normal picture level preset on this projector. Cinema Blackboard(Green) Image 1 Cinema Picture level adjusted for the picture with fine tone. Image 2 Blackboard(Green) Picture level suitable for the image projected on a blackboard.
Video Input Image Level Adjustment 1 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red frame pointer to the Image Adjust Menu icon. 2 Press the Point d button to move the red frame pointer to the item that you want to adjust and then press the SELECT button. The level of each item is displayed. Adjust each level by pressing the Point 7 8 buttons.
Video Input Progressive Interlaced video signal can be displayed in a progressive picture. Off . . . .Not activated. L1 . . . . .Select “L1” for an active picture. L2 . . . . .Select “L2” for a still picture. Image Level Menu Move the red frame pointer to an image icon to be set and then press the SELECT button. Film This function is effective on 3-2 pulldown video source. With this function on, the projector reproduces pictures faithful to the original film quality.
Video Input Screen Size Adjustment This projector has the picture screen resize function, which enables you to customize the image size. 1 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red frame pointer to the Screen Menu icon. 2 Press the Point d button and move the red frame pointer to the function that you want to select and then press the SELECT button. Normal Provide image at a normal video aspect ratio of 4 : 3.
Setting Setting This projector has Setting menu that allows you to set up the other various functions described as follows; Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red frame pointer to the Setting Menu icon. 2 Press the Point d button to move the red frame pointer to the item that you want to set and then press the SELECT button. The Setting dialog box appears. Set the red frame pointer to the item and press the SELECT button.
Setting Enter a Logo PIN code Select a number by pressing the Point 7 8 buttons and fix the number with the SELECT button. The number will change to "✳". If you fixed a wrong number, move the pointer to "Set" or "Clear" once by pressing the Point d button, then return to "Logo PIN code". Enter the correct number again. Repeat this step to complete entering a four-digit number. When the four-digit number is fixed, the pointer will automatically move to "Set".
Setting Ceiling Ceiling Setting When this function is “On,” the picture is top/bottom and left/right reversed. This function is used to project the image from a ceiling mounting the projector. Rear When this function is “On,” the picture is left/right reversed. This function is used to project the image to a rear projection screen. Rear Terminal The COMPUTER IN 2/MONITOR OUT terminal on the back of the projector is switchable for computer input or monitor output.
Setting Lamp mode This function allows you to change the brightness of the screen. Normal mode .....normal brightness Auto mode .........the controlled brightness according to the input signal Eco mode...........lower brightness reduces the lamp power consumption and extends the lamp life ✔Note: Lamp mode is not switched into Eco mode ( is turned on.
Setting PIN code lock PIN code lock Setting This function prevents the projector from being operated by an unauthorized person and provides the following settings for security options. Off ...............the projector is unlocked with the PIN code. On 1 ............require to enter the PIN code every time turning on the projector. .........
Setting Fan Fan This function provides you the following alternatives in the cooling fan's operation after turning off the projector. L1 . . . . . . . .normal operation L2 . . . . . .slower operation than the normal (L1) , but take longer to cool down the projector. In this mode, cooling time after turning off the projector will be extended longer than in the normal mode. Lamp counter reset This function is used to reset the lamp replace counter.
Maintenance and Cleaning Warning Indicator The WARNING indicator shows the state of the function which protects the projector. Check the state of the WARNING indicator and the POWER indicator to take proper maintenance. The projector is shut down and the WARNING indicator is blinking red.
Maintenance and Cleaning Cleaning the Air Filters Air filters prevent dust from accumulating on the surface of the optical elements inside the projector. Should the air filters become clogged with dust particles, it will reduce cooling fan's effectiveness and may result in internal heat build up and adversely affect the life of the projector. Clean the air filters following the steps below. 1 Turn off the projector, and disconnect the AC power cord from the AC outlet.
Maintenance and Cleaning Cleaning the Projection Lens Follow these steps to clean the projection lens. Disconnect the AC power cord before cleaning. 2 Softly wipe the projection lens with a cleaning cloth that contains a small amount of non-abrasive camera lens cleaner, or use lens cleaning paper or a commercially available air blower to clean the lens. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents, or other harsh chemicals might scratch the surface.
Maintenance and Cleaning Lamp Replacement When the life of the projection lamp of this projector draws to an end, the LAMP REPLACE indicator lights yellow. If this indicator lights yellow, replace the lamp with a new one promptly. Top Control POWER WARNING VOLUME + This indicator lights yellow when the life of the projection lamp draws to an end. SELECT CAUTION LAMP REPLACE CAUTION Allow a projector to cool, for at least 45 minutes before you open the Lamp cover.
Maintenance and Cleaning Lamp Replace Counter Be sure to reset the lamp replace counter after the lamp is replaced. When the lamp replace counter is reset, the LAMP REPLACE indicator stops lighting. Turn the projector on, press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red frame pointer to the Setting Menu icon. 2 Press the Point d button to move the red frame pointer to the Lamp counter reset item and then press the SELECT button.
Appendix Troubleshooting Before calling your dealer or service center for assistance, check the items below once again. – Make sure you have properly connected the projector to peripheral equipment as described in "Connecting to a Computer", “Connecting to Video Equipment”and “Connecting to Component Video Equipment” on page15–17. – Make sure all equipment is connected to AC outlet and the power is turned on. – If the projector does not project an image being operated with a computer, restart the computer.
Appendix Some displays are not seen during the operation. – Check the Display item. (See “Setting” on page 39.) PIN code dialog box appears at start-up. – PIN code lock is being set. Input a PIN code (1234 or numbers you have set). (See “PIN code lock” on page 18 and 43.) Computer 2 cannot be selected. – Select Computer 2 at the Terminal item in the Setting Menu. (See “Setting” on page 41.) The Terminal item cannot be selected.
Appendix Indicators and Projector Condition Check the indicators to see the projector condition. Indicators POWER WARNING LAMP REPLACE red/green red yellow Projector Condition The projector is OFF. (The AC power cord is unplugged.) • • • lights green. ✽ When ✽ The projector is preparing for stand-by or the projection lamp is being cooled down. The projector cannot be turned on until cooling is completed. ✽ The projector is ready to be turned on with the POWER ON-OFF button.
Appendix Menu Tree Computer Input / Video Input Input Computer 1 RGB Go to System (1) Component Go to System (2) RGB( Scart ) N/A Quit Computer 2 RGB Go to System (1) Video Auto Go to System (3) Video Go to System (3) S-Video Go to System (3) Quit ✽N/A - - - not applicable Sound Sound Volume Mute Quit 0 - 63 On / Off Computer Input System (1) Image Select Standard Real Blackboard(Green) Image 1 Image 2 Image 3 Image 4 Image Adjust Contrast Brightness Color temp.
Appendix Setting Video Input System (2) Auto 1080i 1035i 720p 575p 480p 575i 480i System (3) Auto PAL SECAM NTSC NTSC4.43 PAL-M PAL-N Image Select Setting Language Keystone Blue back Display Logo PIN code lock Standard Cinema Blackboard(Green) Image 1 Image 2 Image 3 Image 4 Logo Capture Ceiling Rear Terminal Power management Image Adjust Contrast Brightness Color Tint Color temp.
Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 130 MHz of Dot Clock.
Appendix Technical Specifications Mechanical Information Projector Type Dimensions (W x H x D) Net Weight Feet Adjustment Multi-media Projector 11.73" x 2.8" x 8.58" (298mm x 71mm x 218mm) (Not including adjustable feet) 6.2 lbs (2.8kgs) 0˚ to 11.8˚ Panel Resolution LCD Panel System Panel Resolution Number of Pixels 0.
Appendix Accessories Owner's Manual AC Power Cord Remote Control and Batteries VGA Cable Lens Cover with String and Screw PIN Code Label ● The specifications are subject to change without notice. ● LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels. ● The On-Screen Menu and figures in this manual may differ slightly from the product.
Appendix Configurations of Terminals COMPUTER INPUT/COMPONENT INPUT/MONITOR OUTPUT TERMINAL (ANALOG) Terminal : Alanog RGB (Mini D-sub 15pin) Pin Configuration 4 5 10 15 14 2 3 9 8 13 1 7 12 6 11 1 2 3 4 5 6 7 8 Red (R/Cr) Input / Output Green (G/Y) Input / Output Blue (B/Cb) Input / Output ----Ground (Horiz.sync.) Ground (Red) Ground (Green) Ground (Blue) 1 2 3 4 5 6 7 8 Serial RXD --------GND RTS / CTS TXD GND GND 1 2 3 4 Vcc - Data + Data Ground 9 10 11 12 13 14 15 ----Ground (Vert.sync.
Appendix PIN Code Number Memo Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Lock No. Factory default set No: 1 2 3 4* Logo PIN Code Lock No. Factory default set No: 4 3 2 1* *Should the four-digit number be changed, the factory set number will be invalid. While the projector is locked with the PIN code...
A-key to better communications U.S.A. Canada EIKI International, Inc. 30251 Esperanza Rancho Santa Margarita CA 92688-2132 U.S.A. Tel : 800-242-3454 (949)-457-0200 Fax : 800-457-3454 (949)-457-7878 E-Mail : usa@eiki.com EIKI CANADA - Eiki International, Inc. P.O. Box 156, 310 First St. - Unit 2, Midland, ON, L4R 4K8, Canada Tel : 800-563-3454 (705)-527-4084 Fax : 800-567-4069 (705)-527-4087 E-Mail : canada@eiki.
