Owner’s Manual Network Set-up and Operation For Windows Wired and Wireless Setting Projector Set-up and Operation Network Capture Network Viewer Moderator Function USB Display This is the manual for the Network function. Read this manual thoroughly to operate the Network function. First, read the owner's manual of the projector to understand the basic operation of the projector and the safety instructions. The safety instructions in the owner's manuals should be followed strictly.
Compliance This projector provides the wireless LAN module which complies with the module certification. Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
The CE Mark is a Directive conformity mark of the European Community (EC). The Alert Mark is a Directive conformity mark of the European Community. Česky [Czech] Hereby, EIKI Deutschland GmbH declares that this WLAN Module (1AV4U19B25500) is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. EIKI Deutschland GmbH tímto prohlašuje, že tento WLAN Module (1AV4U19B25500) je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Safety instructions CAUTION IN USING THE PROJECTOR VIA NETWORKS ● When you find a problem with the projector, remove the power cable immediately and inspect the unit. Using the projector with failure may cause fire or other accidents. ● If you remotely use the projector via networks, carry out a safety check regularly and take particular care to its environment. Incorrect installation may cause fire or other accidents. CAUTION IN USING NETWORK FUNCTION ● EIKI Industrial Co., Ltd.
Table of contents Compliance..........................................................................................................................................................2 Safety instructions.............................................................................................................................................4 Table of contents................................................................................................................................................
WIRELESS indicator display.........................................................................................................................45 Wireless LAN factory default settings.....................................................................................................46 6. Basic setting and operation..........................................47 Starting up the Browser..........................................................................................................................
Using the Network Viewer function.........................................................................................................124 Use of the projector as FTP server............................................................................................................130 10. Appendix......................................................................133 Use of telnet............................................................................................................................
Operating environment and configuration Required operating environment for computers When operating the projector via the networks, computers should meet the operating environment below.
Network specifications of the projector LAN Terminal Data communication speed 100Base-TX (100Mbps)/10Base-T (10Mbps) Protocol TCP/IP Interface IEEE802.11b/g/n Wireless LAN Communication Mode Data Transfer Speed Wireless Frequency (Channel) Modulation Form AdHoc, Infrastructure 1/2/5.5/11Mbps (IEEE802.11b) 6/9/12/18/24/36/48/54Mbps (IEEE802.11g) Max speed 150Mbps (IEEE802.11n) 2412MHz–2462MHz (CH1–CH11) IEEE802.11g OFDM 54/48Mbps 64QAM, 36/24Mbps 16QAM, 18/12Mbps QPSK, 9/6Mbps BPSK IEEE802.
Useful guide to the network function This manual describes the operation procedure of the projector’s network menu and the provided application software for Windows users. Please refer to this manual depending on the situation.
Chapter 1 1. About LAN functions This chapter describes the features, the mechanism, and connection procedures of the LAN.
Chapter 1 About LAN functions LAN functions and the features This product is loaded with a LAN network function which enables you to project an image on the computer through a projector via Network with dedicated software. With the software, you can also manipulate the projecting image and the projector. This software has functions below and you can use the projector under various network environments to meet the wide-ranging needs of the operation. • Accept both Wired and Wireless LAN environment.
An example of the connection An example of the connection The illustration below shows an example of the projection via the LAN. You can project the image on Computer (1) (Wired LAN connection), or Computer (2) (Wireless LAN connection) through the selected projector . 2.0 1.5 1.0 0.5 0.0 2.0 1.5 1.0 0.5 0.0 2.0 1.5 1.0 0.5 0.
Chapter 1 About LAN functions LAN connection modes Connection modes differ depending on the LAN and computer environments. Connect appropriately for each environment. ■ Wireless LAN, Infrastructure Communication Mode Communicate over an access point between Wired LAN equipment and Wireless LAN equipment. Or, communicate over an access point among multiple Wireless LAN equipment. Wireless LAN equipment will select an access point to communicate SSID/ESSID modes.
LAN connection modes ■ Wired LAN Communication Mode Communicate via the LAN line. Computer(1) Computer(2) Computer (3) ✳ Operate the computer mouse with the remote control. When the projector’s remote control employs mouse operating function, you can operate the computer by the remote control. To use the remote control, point to the projector. You do not need to connect the USB cable to operate the computer mouse.
Chapter 1 About LAN functions 16
Chapter 2 2. Setup procedures This chapter describes how to install the Network Capture 5 software and how to set up the networks.
Chapter 2 Setup procedures To use the projector via the networks, follow the setup procedures below. STEP 1 Install the software on computers. Install the software recorded in CD-ROM on each computer which will be operated. Read following pages of this chapter to install. STEP 2 Select Wired LAN or Wireless LAN then connect the LAN and set the configuration. Decide depending on the LAN environment. Wired LAN............. Refer to “4. Wired LAN Configurations” (pp.27–34). Wireless LAN........
Installing the software Installing the software It is required to install the software into your computer to use the Network Capture function . Please install the software as follows. Note: To install the software into the computer with Windows 2000, Windows XP or Windows Vista, you should logon as administrator. Before installation, make sure that the other applications are closed, otherwise proper installation cannot be made.
Chapter 2 Setup procedures As the "License Agreement" will appear, read contents carefully and click Yes button if you agree to the license agreement to proceed with installing. During the installation, following window may appear, click Continue Anyway button. 3 Click Finish to complete the installation. Installed software The following 3 softwares are installed on your computer.
Installing the software File Converter 2 installation 1 Set the supplied Network Viewer & Capture 5 CD2 ROM into the CD-ROM drive of your computer. Double click SetupDrv.exe icon in the "Driver" folder in the CD-ROM. Select "English [United States]" from the pull-down menu on the language selection window and then click Install button to start installing. Installed software and places Network Viewer 5 (File Converter 2) is installed in the "Printers and Faxes" folder in the "Control Panel".
Chapter 2 Setup procedures Installation of Driver for USB display It is required to install the software into your computer to use the USB display function . Please install the software as follows. 1. Select “Display” in the “USB terminal” from the setting menu of the projector. 2. Select “USB Display” with the Point ed buttons and press SELECT button. Then the Menu will disappear, the “Please wait...” message will appear, and switching operation will start.
Chapter 3 3. Names and functions of the operation screen This chapter describes the functions of each part of the operation screen.
Chapter 3 Names and functions of the operating screen Network connection standby display Turn on the projector and select either “Wired” or “Wireless” from the input menu of the projector. The “Please wait...” message will be displayed on the screen. After short time, the network connection standby display screen will appear as below. While the “Please wait...” message is shown, some operations are invalid.
Network Capture 5 window Network Capture 5 window This software is to project the computer screen via the networks. Select "All Programs" from the start menu --> Network Viewer & Capture 5" --> "Network Capture 5", then following screen will appear. Then the program will start. r t Disable for this model y u i o q w !0 e !1 !2 !3 Parts Names and Functions of the Screen q Search PJ button Search the projector connected to the networks.
Chapter 3 Names and functions of the operating screen t Start communication button Enter the Communication mode, and then , the capture edit window starts. The selected projector shows the capture edit window. y Start real time capture button Capture (Project) the computer screen in real time. After the execution of "Start real time capture", the application window disappears. • • • v u One-shot capture button Copy and capture (project) the computer screen without modification.
Chapter 4 4. Wired LAN configurations This chapter describes the preparation for Wired LAN setting with projectors and how to set the LAN environment.
Chapter 4 Wired LAN configurations Setting procedures and contents differ depending on the LAN installation location. When installing, consult your system administrator to set up the LAN appropriately. Connecting to the LAN line Connect the shielded LAN cable to the LAN connection terminal of the projector. LAN Connection Terminal LAN Cable** ACT Lamp (Orange) When the projector is connected to the 100 BaseTX network, light or blink as follows; - Light when connecting to the network.
Network environment setting 4. Select "Network setting" in the Network menu and press SELECT button, and then the LAN setting screen will appear and selected LAN settings will be displayed. Adjust each item to the setting environment. Consult your system administrator about the detailed settings. Move among the items with the Point ed buttons and press SELECT button, move among the columns with Point 7 8 buttons, adjust the figures with Point ed buttons, and then press SELECT button to set. 5.
Chapter 4 Wired LAN configurations Confirming the operation Confirm that the projector has connected to the LAN properly. 1. Activate “Network Capture 5” which is installed into the computer connected to the LAN . 2. After “Searching projector” message appears, the name of the projector* appears on the Network Projector List, then the network setting has completed properly. When the name of the projector does not appear and error screen appears, the network has not connected yet.
Confirming the operation When set up the projector in the location separated by the router and the segment is different; Projector will not be found nor displayed. In that case, the projector needs to be searched directly by the IP address. 1. Press Specify IP button. "Search specified IP address" window appears. 2. Click Add button, "IP address set up" window appears. Enter the IP address of the projector and Click OK button. Then, the projector will be added on the "Search specified IP address" window.
Chapter 4 Wired LAN configurations Network PIN code The Network PIN code is to restrict the access from the networks to the projector. After setting the Network PIN code, you need to enter it to operate the projector via the networks. 1. Select "Network PIN code" in the Network menu, and press SELECT button. The Network PIN code screen will appear. 2. Set the Network PIN code. Set the figures with the Point ed buttons and move to the next items with the Point 7 8 buttons.
Wired LAN factory default settings Wired factory default Select “Wired factory default” in the Network menu and press SELECT button. All the wired LAN settings will go back to the factory default settings as shown below table. Wired LAN factory default settings SELECTED LAN Parameter Wired 1 Wired 2 Wired 3 DHCP OFF ON OFF IP ADDRESS 169.254.100.100 192.168.100.100 192.168.100.100 SUBNET MASK 255.255.0.0 255.255.255.0 255.255.255.0 GATEWAY ADDRESS 255.255.255.255 255.255.255.255 255.255.
Chapter 4 Wired LAN configurations USB Display The image and sound are sent to the projector by connecting the computer to the projector with a USB cable. 1. Select “Display” in the “USB terminal” from the setting menu of the projector. 2. Select “USB Display” with the Point ed buttons and press SELECT button. Then the Menu will disappear, the “Please wait...” message will appear, and switching operation will start.
Chapter 5 5. Wireless LAN configurations This chapter describes the preparation for Wireless LAN setting with projectors and how to set the LAN environment. This projector contains the Wireless LAN module. The setting procedures and configurations differ depending on the LAN installation location. Consult your system administrator for installation and set the LAN appropriately. To operate via Wireless LAN, your computer has to be equipped with a Wireless LAN card adapter which supports IEEE 802.11b/g/n.
Chapter 5 Wireless LAN configurations Setting the network environment The projector contains the Wireless LAN adapter. Set the Wireless LAN network through the projector menu. Detailed network settings will be made with browser. Refer to “6. Basic setting and operation”. ➔ "Network configuration" (p.55). Complete the settings described in this chapter before performing the steps in “6. Basic setting and operation.” Setting procedures 1.
Setting the network environment 5. After completing all the settings, select “Set” and press SELECT button. Now, all procedures have been done. To cancel the adjusted settings, select the "Cancel" and press SELECT button. If you want to set the security, select "Next" and press SELECT button to proceed to the security setting window and refer to the following pages in detail. Network setting DHCP: On DHCP: Off For configuring of WEP, WPA-PSK, WPA2-PSK security, select “Next”.
Chapter 5 Wireless LAN configurations Configuring security with the projector Configure security with the projector by following the steps below. After configuring the network in “5. Wireless LAN Configurations” (p.35-46), select “Next” in the LAN setting screen and press SELECT button. The security configuration screen appears. Refer to “6. Basic setting and operation” ➔ “Configuring wireless LAN setting and security setting” (p.57) as well.
Configuring security with the projector Use of security type "WPS"(Wi-Fi Protected Setup) By using WPS (Wi-Fi Protected Setup), the communication via ESSID and WPA2 security type between the Wireless LAN access point and the projector can be configured without complicated setting procedures.
Chapter 5 Wireless LAN configurations WPS PIN code 1. Select "WPS PIN code" in "Security" Menu, and press SELECT button. Use the Point ed buttons to select "Set" and "WPS PIN code" will appear by pressing SELECT button. WPS PIN code configuration screen 2. Configure the eight-digit number of “WPS PIN code” which is displayed to the access point according to the instructions manual of the access point. And then select “Set” and press SELECT button within 2 minutes after configuration of the access point.
Configuring security with the projector Use of security type "WEP" 1. Use the Point ed buttons to select "WEP" security type. 2. Select “Key index”. Use the Point ed buttons to choose the HEX or ASCII key. The four (#1–#4) kinds of WEP keys can be configured. Use the Point 7 8 buttons to move to the right frame; use the Point ed buttons to select a WEP key number (#1–#4). WEP configuration screen Refer the table below for the usable number of characters at the WEP security option.
Chapter 5 Wireless LAN configurations Use of security type "WPA-PSK", "WPA2-PSK" 1. Use the Point ed buttons to select "WPA-PSK" security type. WPA-PSK(TKIP) configuration screen 2. Use the Point ed buttons to select the key field and press SELECT button. The PSK key entry screen appears. Enter the PSK key by using the Point buttons. If the input PSK key has an error, the PSK key is indicated in red. 3.
Easy wireless setting Easy wireless setting With this setting, you do not need any complicated LAN setting procedures. The network type will be AdHoc mode. CAUTION: This function can be used only when logged in by Administrative right with Windows XP and Windows Vista, and cannot be used with Windows 2000. Windows XP should be Service Pack 1 or later version. Setting Procedures 1. Turn on the projector and select “Network” in the Input menu of the projector. 2.
Chapter 5 Wireless LAN configurations Computer environment and Wireless LAN connection; Wireless LAN with Wireless Easy setting connection will be made via AdHoc mode. For setting contents, refer to “Wireless LAN factory default settings” (p.46). With the Easy setting, computer’s LAN environment setting will be switched to the setup environment. Because of that, the LAN cannot work for the other operation while using “Network Capture 5”.
WIRELESS indicator display WIRELESS indicator display When the wireless LAN configuration is set up correctly and the wireless communication is established with the access-point or computer in the network, the WIRELESS indicator on the front panel lights up. When sending or receiving of data, it blinks.
Chapter 5 Wireless LAN configurations Easy wireless setting Wireless LAN factory default settings Factory default settings for Wireless 4, Wireless 5, and Wireless Simple as follows. Selected LAN Setting Items 46 Wireless 4 Wireless 5 Wireless Simple DHCP OFF ON OFF IP ADDRESS 169.254.100.100 192.168.100.100 169.254. * . * SUBNETMASK 255.255.0.0 255.255.255.0 255.255.0.0 GATEWAY ADDRESS 255.255.255.255 255.255.255.255 255.255.255.255 DNS ADDRESS 255.255.255.255 255.255.255.255 255.
Chapter 6 6. Basic setting and operation Describes basic operation and settings below by using the web browser. • Initial setting Setup the basic setting such as Projector name, Network PIN code, Time setting, etc. • Network setting Configure Wired/Wireless LAN environment. • E-mail Setting Configure E-mail function to manage the projector. • SNMP Setting Configure SNMP function to manage the projector.
Chapter 6 Basic setting and operation Starting up the Browser 1. Turn on the projector. 2. Start up the Network Capture 5. The Network Capture 5 searches projectors in the network and lists up the IP address or projector name of the projector on the Network Projector List. 3. Double click the projector to set from the Network Projector List. 4. The web browser will start up and display the setting page of the projector.
Starting up the browser Display of main setting page The following main setting page will be displayed depending on your display mode selection. Perform various kinds of settings through this page. Click on the menus to display the control and setting pages. z Main setting page in the Standard Mode display Clock display Display on or off by clicking text ON or OFF Sub menu tab Switches the sub menu tab. Page numbers Switches the pages by clicking the number's tab.
Chapter 6 Basic setting and operation x Main setting page in the Light Mode display Sub menu tab Page numbers Returns to the display mode selection page. Main menu Setting page Returns to main menu ✐ T he blank page appears if your PDA does not provide a Adobe Flash Player. You need to install the Adobe Flash Player. (☞p.49) The network viewer function in the Light mode has following limitations; - Cannot select the program or folder for the display.
How to use the setting page Type of the setting pallet Text box setting Enter the number or text and then click Set button. or Change a value with s or t button and then click Set button. The value changes quickly when s or t button is kept pressing. Pull-down menu setting Select an item with pull-down menu button and then click Set button. or Select an item by clicking s or t button.
Chapter 6 Basic setting and operation Initial setting After installing the projector, perform the following basic initial setting. Click Initial Setting on the main menu to display the initial setting page. Item Description Language.................. Switches display language on the setting page. English or Japanese. Model name............. Indicates the model name of the projector. Projector name........ Sets the name of projector.
Initial setting Network PIN code setting This is to set the Network PIN code to restrict the access from an unauthorized person through the network. Enter a 4-digit number as the Network PIN code onto the text box and click Set button. The projector's network part begins restarting and it takes about 20 seconds. Close (Quit) the web browser and access to the login page again in 20 seconds. This is to perform the login authentication firmly.
Chapter 6 Basic setting and operation Item Description NTP address.............. Enter the address of NTP server. Please consult your network administrator for setting up of the NTP server. Time zone..................Sets your country or region's time zone Temperature............. Switches display temperature unit Centigrade or Fahrenheit Time setting.............. When clicking AUTO button, the date and time set on your computer are set to the projector.
Network configuration Network configuration Click Network on the main menu. The following setting page is displayed. Set up the projector's network environment on this Setting sub menu. Setting of LAN 1. Select a type of LAN from Change setting pull down menu. LAN1(Wired) LAN2(Wired) LAN3(Wired) LAN4(Wireless) LAN5(Wireless) Simple(Wireless) USB display*1 For the default setting of the above LAN, see the items "Wired Factory Default Setting" or "Wireless Factory Default Setting".
Chapter 6 Basic setting and operation 2. S elect either "Manual" or "DHCP" from IP configuration pull down menu. When "DHCP" is selected, IP address, Subnet mask, Default Gateway, DNS are automatically configured by DHCP function. Only the DNS address allows you to set up manually if the DNS address information is not provided on your DHCP server. When selecting "Manual", configure all the items manually. For further information, contact your network administrator.
Configuring wireless LAN setting and security setting Configuring wireless LAN setting and security setting Configure the wireless LAN setting and security setting for Wireless 4 and Wireless 5. Configuring wireless LAN setting 1. Click page [2] of setting pages. Following wireless LAN setting can be done. After completing the configuration, press Set button. Item Description Wireless Mode.........Select the Communication standard 802.11b, 802.11b/g or 802.11b/g/n. Network Type...........
Chapter 6 Basic setting and operation Configuring wireless LAN security setting lick page [3] of setting pages. Following wireless LAN security C setting can be done. After completing the configuration, press Set button. Item Description Network security....Sets the type of encryption. Following types are available. Disable WPS Push Button WPS PIN code WEP64(40)bit Open WEP64(40)bit Share WEP128(104)bit Open WEP128(104)bit Share WPA-PSK(TKIP) WPA2-PSK(AES) Input type.................ASCII or HEX.
Configuring wireless LAN setting and security setting Setting of WPS Push button 1. Select “WPS Push Button” in the “Network security” and press Set button to start WPS configuration. 2. C onfigure WPS of the access point within 2 minutes. After configuration of the access point, the network between the access point and the projector will be performed automatically. 3. The network setting will be updated after finishing configuration.
Chapter 6 Basic setting and operation E-mail setting This product has an E-mail function which can send an alert message to users or an administrator if it detects an abnormality on the projector or run out of the life span of the lamp. Click E-mail Setting on the main menu and follow the below steps. 1 Setting SMTP server and administrator address Set the server name or IP address of the SMTP server*1 and administrator address.
E-mail setting 2 S etting SMTP authentication Set the SMTP authentication concerned. Please contact your network administrator in details. Item Description SMTP authentication setting Auth....................... Sets authentication setting option. (OFF, SMTP Auth, POP before SMTP) SMTP Auth . ........ Sets user authentication setting option when selecting "SMTP Auth" in above column. (CRAM-MD5, LOGIN, PLAIN) After completing the settings, press Set button. User ID........................
Chapter 6 Basic setting and operation 5O ption selection for sending alert mail Option Click Option sub menu tab. Check the condition items under which alert mail will be sent and click Set button. Please refer to the item "Examples :Type and contents of alert mail" described as below. [1]–––––––––––––––––––––––––––––––––– o When PJ lamp is off. o When PJ lamp replacement time is reached. o When PJ needs service. o When internal PJ temperature is too high.
E-mail setting ● When PJ needs service:: TITLE: Message from projector 10-03-2007 00:59 Projector Model Name: model name TCP/IP: 192.168.1.201 Projector Name: Proj05 It sends you following message. * Maintenance requirement from Projector is detected. Check up LED status of projector and consult with the dealer. MAIN, MAIN, MCI, P-FAIL 1.8V P-FAIL OK OK NG Error information ✐ Maintenance requirement from Projector is detected.
Chapter 6 Basic setting and operation SNMP setting This product provides a SNMP (Simple Network Management Protocol) agent function. The SNMP consists of a manager and agents. The group which exchanges information with SNMP is called "Community". There are two access modes in a community, Refer (read only) and Set (read- write). This product allows to use Refer (read only) only. The SNMP message informs the projector status called "Trap" to an administrator.
SNMP setting Trap Item Description Community name............ Enter community name to send "Trap". Default name is "public". Trap address............. Enter IP address of the SNMP manager computer to receive "Trap". Up to 10 address can be registered. ✐ Up to 10 trap addresses can be registered. Trap check/delete Check and delete the trap address Checking the registered trap address and deleting the address. To delete the address, tick the check box in front of the IP address and click Delete button.
Chapter 6 Basic setting and operation Trap option Trap option setting Tick the check boxes in front of the condition item to send the trap. ✐ Click Set button if you tick or un-tick the check box on a page. [1]–––––––––––––––––––––––––––––––––– o When PJ lamp is off. o When PJ lamp replacement time is reached. o When PJ needs service. o When internal PJ temperature is too high. [2]–––––––––––––––––––––––––––––––––– o W hen PJ is turned into Standby in proper user operation.
Chapter 7 7. Controlling the projector Describes controlling and setting of the projector by using the web browser.
Chapter 7 Controlling the projector Power control and status check Click Power & Status on the main menu. The control page will be displayed. By clicking ON or Standby button on the page, the power of the projector can be controlled. Confirmation window as shown in the below appears when the Standby button is pressed. Popup confirmation window Item Description PJ status Power . ........................... Displays the status of the lamp. (ON, OFF, On starting up, On cooling down) Status ............
Power control and status check About projector condition Status Description Normal...................................................................Projector is operating normally. Power management in operation.......................Power management is operating Lamp failure........................................................Lamp failure is occurring Abnormal Temperature...................................The temperature of the projector became too high Cooling down after abnormal Temp.
Chapter 7 Controlling the projector Controls Click Control on the main menu. The setting method differs depending on the contents of the page. Click on the page number to change pages and select desired setting items. ✐ Please see the owner's manual of the projector to have the further information of each control item. Input This function is to select the input mode and source mode of the projector. Click Set button after selecting the input and source mode. Item Description Input.....................
Controls System This function is to select the system of signal input to the projector. The available system mode are listed on the pull-down menu button according to the input signal. Select a system and then click Set button. Available selection at the RGB(PC analog) input Item Description XGA1........................... It automatically switches to the proper computer system of the input signal. * The computer system modes (VGA, SVGA, XGA. SXGA, UXGA, WXGA...) which meet the input signal listed.
Chapter 7 Controlling the projector Image adjustment This function is to adjust the projected picture image and save the image mode. To store the adjusted value, click Store button, and to load the adjusted value, click Load button. Item Description Contrast.....................Adjusts picture contrast Brightness.................Adjusts picture brightness Color............................Adjusts picture color saturation Tint...............................
Controls Sound This function is to adjust the sound of the projector. The values in the text box represent the current control value or status. Item Description Volume....................... Adjusts the sound volume from the speakers. Mute............................ Suppresses the sound.
Chapter 7 Controlling the projector PC adjustment Click PC Adj. on the main menu. This function is to adjust the signal from the computer connected to the projector to obtain the proper picture image on the screen. Item Description Current mode............ Displays a current mode like VGA, SVGA, XGA, SXGA, UXGA, WXGA, etc. or MODE1 - MODE5 are the customized mode created by using the "Mode Store" function described below. Auto PC adj............... Performs automatic adjustment. Fine sync...............
Setting up the projector Setting up the projector Click Setting on the main menu. This function is to set up the projector. Select the sub menu [Screen setting], [Setting 1] or , [Setting 2] and then set up each setting. Item Description Screen......................... Switches the screen mode. There may not be available mode depending on the input mode as shown in the table below.
Chapter 7 Controlling the projector Item Description Language.................. Sets the language display of projector's on-screen display menu. Auto setup................ Executes the Auto PC Adj, and Input Search function below according to the each setting after clicking Start button. Auto PC adj..........Sets Auto PC Adjustment mode. Input search........Sets the auto-input signal detection mode. Auto keystone....Sets Auto Keystone mode. Background..............
Setting up the projector Item Description Fan............................... Sets the cooling options after turning off. L1 Normal cooling L2 Silent cooling Fan control...............Sets the fan control speed. Off Normal mode On1 Highland mode 1 On2 Highland mode 2 On3 Highland mode 3 Lamp Corres. value.... Displays the use time (Corresponding value) of the lamp and reset the counter. Item Description Filter counter............ Displays the filter use time. Reset the time after filter clean-up.
Chapter 7 Controlling the projector Timer setting This page is to set the timer to turn the projector off or on at a programmed day/date and time. Follow the steps below for setting. Click Timer on the main menu. "---" will appear on the current time when the time is not set up correctly.
Timer setting 2 Set an execute time Type the time with (Hour:Minute) and 24 hours format. Ex.: Type [18:25] if you specify [PM 6 o’clock and 25 minutes]. 3 Select an event action Select an event action from the pull-down menu. Event Action ON................................... Turns on the projector OFF................................. Turns off the projector Lamp High................... Changes lamp mode to "High" Lamp Normal.............. Changes lamp mode to "Normal" Lamp Eco......................
Chapter 7 Controlling the projector Notes on timer setting ✐U p to 10 timer events can be registered. Timer events always operate according to the next valid event depending on the projector's power status. In the example below, event 3 turns on the projector so next event 4 (also turning on projector) will not be effective because the projector is already turned on. Similarly, when the projector is turned off by event 5, event 6 OFF will not be effective in turning it off again.
Projector information Projector information This page is to display the basic information of the projector status. Click Information on the main menu. Items Description Input............................Displays selected input and source. System........................Displays selected signal system. Signal..........................Input signal status Screen.........................Displays screen mode. Lamp status............... Displays lamp status with an animation.
Chapter 7 Controlling the projector Indication of the lamp status Icon display/background Status White-Yellow/Blue Lamp on (Normal) White-Yellow/Red Lamp on (Lamp is being used over a specified use time, replace lamp immediately) Gray/Blue Lamp off (Normal) Gray/Red Lamp off (Lamp is being used over a specified use time, replace lamp immediately) Red/Blue with X Lamp failure (Lamp failure, check the lamp condition) Red/Red with X Lamp failure (Lamp failure and lamp is being used over a specifi
Multi-control Multi-control Controlling and setting the multi-projectors When you install multiple projectors in the network, you can control and set up them together. Click Multi Control on the main menu to display the control page. Note: To control the multiple projectors, each projector must be set the same Network PIN code. Example of multi control PJ1 PJ2 PJ3 PJ4 PC6 PC5 PC4 Select Input2 for PJ1 to PJ4.
Chapter 7 Controlling the projector Start/stop the multi control To start or stop controlling the multi-projectors, click Multi control setting menu and select ON or OFF. Switches on and off the multi-control function Multi control setting OFF...........Stops multi control function ON............. Starts multi control function. The multi control menu will appear when ON is set. These items of menu are linked to the main menu.
Multi-control Register the projector To use the multi control function, register the IP address of the projector you intend to control. Click Pj registration sub menu tab and set the IP address, Memo and Multi control item, then click Set button. Items Description IP address..................Enter IP address of the projector to control Memo.........................Enter projector name or installed location etc. Multi control item Control.................. Controlling the projector Control & Image.......
Chapter 7 Controlling the projector Change the mode of the registered projector To change the mode of the registered projector, select a mode with the pull-down menu button under the IP address of the target projector and then click Set button. Mode Operation Control........................ Controlling the projector Control & Image............... Controlling and displaying images Image.......................... Displaying the images OFF..............................
Multi-control Check & Change page in the light mode Following functions in the "Check & Change" page are not available in the light mode. - Changing the control mode. - Deleting the registered IP address - Indicating the each status - Indicating the each memo This indicates that the mode is "Image". Connection status Blinking: Connected Gray: Disconnected This indicates that the mode is "Control".
Chapter 7 Controlling the projector Viewer auto setting all together "Viewer auto display" can be set all together. Set "ON" the multi control setting and select [3] Auto display from Viewer sub menu (selected by ‘Multi-control’ - “Network Viewer” menu). Set the display time periods and repeat times for the auto image display. After clicking Start button, the registered projectors start playing back the auto image display in sequential.
Chapter 8 8. Network capture functions Network Capture is a function to display the screen image and reproduce the sound of the computer via the network.
Chapter 8 Network capture functions About Network Capture function The Network Capture is a function to display the screen image and reproduce the sound of the computer which has a Network Capture 5 software by the projector through the network. This function has 3 kinds of mode as below. - Real Time Capture (+p.93) A function to display the screen image and reproduce the sound of the computer by the projector through the network in real time. - Network Communication (+p.
About Network Capture function Commands on the task bar When the Network Viewer & Capture 5 icon on the task bar is clicked, the popup menu will appear. It provides according to the operating modes as shown in the table below. Menu during Real time capturing One-shot executing Real time capture executing Start real time capture One-shot capture Terminate capture Window show.. Version information.. Shut down One-shot capture Terminate capture Window show.. Version information..
Chapter 8 Network capture functions Parameter set up Click Parameter set up button and setup the parameters on the Parameter setup window. Items Description Connection setting Capture port................ Sets the capture port no. on the projector. Default is 9000. Pincode.......................... Sets the Network PIN code on the projector. PJ search time.............. Sets the time to search the projector between 1 to 60 seconds. Default is 5 seconds.
Using the Real Time Capture Using the Real Time Capture This is a function to project the screen image and reproduce the sound of the computer by the projector in real time. The captured image projected by the projector can be selected from the computer, web browser and the projector respectively. Registering the computers Up to 30 computers can be registered. 1 Access to the control page of the projector by using the web browser. From the Network menu, click Capture tab to display the setting page.
Chapter 8 Network capture functions [1] Control by the computer * PC provides the Network Capture. PC1 PJ2 PJ1 Project this screen PC2 PC2 image with PJ2. Capture PC3 PC4 PC6 PC5 * Start capturing from the PC1. Select input mode to "Network" previously. 1 Start up Network Capture 5. 2 Select the projector(s) listed on the projector list on the application window and click Start real time capture.
Using the real time capture [2] Control by the web browser * PC provides the Network Capture. PC1 PJ2 PJ1 PC2 Capture PC3 PC4 PC6 PC5 Project a screen image of PC1 with PJ2. * S tar t capturing of t h e P C1 f r o m t h e PC5. Select "Network" as input mode previously. 1 Access to the control page of the projector by using the web browser. From the Network menu, click Capture tab to display the setting page.
Chapter 8 Network capture functions [3] Control by the projector * S tar t captur ing of the PC1 from the projector PJ2. * PC provides the Network Capture. PC1 PJ2 PJ1 PC2 Capture PC3 PC4 PC6 PC5 Project a screen image of PC1 with PJ2. Select "Network" in the Input menu previously. 1 Select "Network capture" in the Network menu. Press Point 8 or SELECT button.
Using the real time capture [4] Control by the computer with USB memory PC1 * S tart capturing of the PC1. Project PC2this screen image with PJ1. PJ1 ＊USB memory provides Auto Capture program. The real time capture function can run automatically on the computer without the Network Viewer & Capture 5 software installed by executing the Auto Capture program in the USB thumb drive connected to the computer. The USB thumb drive for Auto Capture is supplied with this projector. 1.
Chapter 8 Network capture functions Example of advanced use Displays the presentation data stored in the computer by using the wireless mouse function from the projector. 1 Start capturing of the computer PC1 by using the projector. S elect “Network Capture” icon from the menu and select "PC1" and then select "Connect" (☞ p.96). => The Network Capture software installed in the selected computer will start capturing.
Using the Network Communication PJ1 PC6 Capture PC1 PC2 PC5 Capture a screen image of PC5 and make marking with a tool. * T he Main PC is a computer which started using communication function, and serves own computer screen captured image to the Sub PC. The Main PC has an authority to quit using whole communication. To become the Main PC, execute the command "Start Communication" or "Capture transfer". For further information, see item "How to use the Network Communication". (☞p.
Chapter 8 Network capture functions Description of capture editing window Start Network Capture 5 and select the projector(s) on the projector list on the application window and click Communication Start button. The application window will disappear and the capture editing window will appear on the computer screen as below. For basic operation of each menu, refer to the item "Menu tree" below. Menu Tool bar Capture Image Authority status indication frame (☞p.
Using the Network Communication Tool bar button names The following commands are assigned to the tool bar buttons. For each operation, refer to the description of the item "Menu tree".
Chapter 8 Network capture functions How to use the Network communication Start the communication 1 Display an image on the computer screen. 2 Start Network Capture 5. The application window appears and the projectors in the network are listed. 3 Select the projector(s) and click Start Communication button. The application window disappears and the capture editing window with a captured image appears on the computer screen. The projector displays captured image on the screen.
How to use the Network communication Edit capture image Drawing figures 1 Click " :Pencil" button on the form tool bar. 2 Select its attribute (shape, width, color and translucence) from the form and attribute tool bar. 3 Drag a mouse pointer on the screen image to draw the figure. Erase drawn objects 1 Click " :Eraser" button on the form tool bar. 2 Select its attribute (shape, width) from the form and attribute tool bar. 3 Drag a mouse pointer on the screen image to erase the figure.
Chapter 8 Network capture functions Drawing letter 1 Click " :Letter frame" button on the form tool bar. 2 Select a color of text with color tool bar. 3 Drag a mouse pointer on the screen image to specify the area of the letter frame. The letter input dialog window will appear. 4 Enter the letter onto the window. To change the letter attribute, click Letter attribute button. See the item "letter attribute setting" below. 5 Click OK button to fix the content.
Network Communication operation and change of state Network Communication operation and change of state Network Communication can be used under the environment which one or more computers are connected to the projector via the network. Preparation Start up the Network Capture 5 software on the subject computer. Set standby the projector or turn it on. Check IP address of the subject computer is registered in the connection list (☞p.99).
Chapter 8 Network capture functions Executing the forcing mode The network capture setting of the web page provides a forcing executing command. This command executes the release of authority or ending the communication forcibly. This is useful when the other subject PC keeps an authority all the time, or when the condition of the communication is not stable. Click page 2 Communication Setting from the menu "Network"-"Capture". Execute command by clicking the button Free, Quit or Update.
Moderator function Moderator function This function is useful for a moderator or a teacher to conduct a meeting or a class, where all the participants including the moderator (teacher) are assigned a computer, to project images from each participant’s computer. A moderator (teacher) has the right to decide which computer image should be projected. One moderator (teacher) can conduct up to 50 computers.
Chapter 8 Network capture functions Preparation for using the moderator function First, follow the procedure in “2. Setup Procedure” ➔ “Step 1–3” (p.18) and confirm that the setting status is set as written below. • Network Capture 5 is installed on the moderator's computer and each client’s computer and each computer image can be projected. Following application window appears when the Network Capture starts.
Moderator function Description of application window Column Description Status..........................Indicates the projector's condition. On real time, On One-shot capture, On Standby, In Moderator mode, etc. User.............................Indicates the client name (nickname or IP address) used by the projector. Error.............................Indicates the error status during executing the real time capture or one-shot capture. Parameter set up.... Sets the parameter of capturing.
Chapter 8 Network capture functions Moderator's password setting up This enables you to set up the password to join in the moderator's group. Start up the network Capture 5 and click Parameter set up button on the application window. On the moderator function setting item on the parameter set up window, set up the password of Moderator 's password. Up to 15 characters can be used for the password. Default password is blank.
Error information Error information Error messages Cause and corresponding Set up the parameter. Error when the communication is executed. The parameter setting (host name, capture port) has not been set. ➔ Check parameter setting (+p.92) It has not been registered to PJ as a group. Error when Start Communication or Start real time capture is executed. The IP address of the computer has not been registered. ➔ Register the IP address by using the web browser (+p.
Chapter 8 Network capture functions 112
Chapter 9 9. Network Viewer functions Network Viewer is a function to display the image data stored in the file servers by the projector through the network. Describes the file converter software File Converter 1, File Converter 2, the program creator software Program Editor, and how to use Network Viewer.
Chapter 9 Network Viewer functions Creating the available data [Network Viewer 5] The image available with this projector is the JPEG format (.jpg). There are several types of JPEG data. Some data may not be projected. Before using the images with the Network Viewer function, it should be converted to the optimized JPEG data for this projector.
Create the available data Menu Tree Menu Sub Menu Description View Update Preview size Option Convert each file Convert a folder Version information Updates contents of the preview window Sets size of the preview image, Large, Middle, Small Sets default of the output destination and conversion mode Converts a file into a JPEG file individually Converts files in a folder into JPEG files at once Displays the version information Tools Conversion Help Command Tool Button Convert each file Convert a fol
Chapter 9 Network Viewer functions 2 When converting each file, select a preview image first and then click Convert each file. ✐ To select two or more files at once, press and hold "Shift" key or "Ctrl" key and then click the preview images. When converting all the files in a folder, select a folder and click Convert a folder. 3 As the confirmation window appears, check the conversion object and conversion type and then click OK button.
Creating the available data [Network Viewer 5] Setting of output destination and conversion mode When clicking Change button on the confirmation window in the step 3 on the previous page, following option setting window appears. Output destination Select either Folder or FTP server as the output destination of the converted files. Folder Output folder........... Specify a folder in the local hard disk or shared computer in the network FTP server Host name.................
Chapter 9 Network Viewer functions [2] How to use the Network Viewer 5 (File Converter 2) The File Converter 2 is a kind of the printer driver software to convert to the optimized JPEG data for the projection from the any documents created by the other software such as text editor, spreadsheet or presentation software. It is possible to convert to the JPEG file from the any kinds of documents created by the software which has a "print" menu.
Creating a program file [Program Editor] Creating a program file [Program Editor] Network Viewer 5 (Program Editor) is a tool to make a program file which specifies the display order of the images and its file path in the file server (FTP server). The Program Editor creates a folder "DispParam" at the login root directory in the FTP server, and files with each program name into this folder. These files are called "Program".
Chapter 9 Network Viewer functions 4 Click New button. 5 Enter a program name and click Add button. 6 The folder selection window appears and select a folder in which the JPEG data are stored and then click Add button to register into the folder lists. Change : C hanges the contents of the program file. Remove : Removes the program from the list. Add.......................Displays the folder selection window. Delete..................Deletes the folder path from the folder list. UP...................
Creating a program file [Program Editor] Setting up the display order and time of the images In the default setting, the display order of the images is the same as ASCII code order of the file name. To change the display order or to set up the display time, take the following procedures. Display the folder list window in step 6 of the previous page. 1 Select a folder list contains images to change. 2 Click Edit button. The images in the selected folder are displayed with the file name on the index window.
Chapter 9 Network Viewer functions 3 To change the display order, select* 1 files and then click UP or DOWN button on the menu bar to move them onto your desired place, or select files and then drag and drop them onto your desired place with mouse. 4 To change the display time*2, select*1 files and then click Display time button on the menu bar to display the Display time setting window. Check "Display time" in the check box and set the display time.
Creating a program file [Program Editor] Example of the created program selection Use the web browser to access to the control page of the projector. Click "Viewer" of the Network menu on the web page, then connect to the FTP server and select the program name which was made at previous section. The projector starts displaying the images along the program. For further information, please see "Using the Network Viewer function" (☞ p.124). ✐ This function is not available in the light mode.
Chapter 9 Network Viewer functions Using the Network Viewer function The Network Viewer is a function to acquire the JPEG image data from the file servers placed in the network and project them on the screen. The projected image data are specified by the folder unit. You can set the display time and the number of repeat, and also you can register those folders as the program. *The network viewer function cannot be used when the network capture function is used.
Using the network viewer function 2 Setup the setting page [1] of the Visual display. Item Description Host name................. Enter the host name or IP address of FTP server, yourftp.server etc. Folder Path................ Use "/"(root directory) normally, or enter the directory name follow the "/" as shown in the below example if you have a specified directory in the server. /data/ User ID*1. ................... Enter your login account of the FTP server Password*1................
Chapter 9 Network Viewer functions After clicking Set, the file list or preview list of the selected folder or program is displayed on the window. Decides a image to start auto display with radio button Selects a page The original image is displayed on another window by clicking on the preview image or file name Button Operation <<................................. Go to the preceding start up image in the auto display function >>.................................
Using the network viewer function 4 Auto Display setting and control page [3] Repeat times (0 to 255 times) * 0 means endless play Display time*1 of the image (3 to 240 sec.) Error info. Click here to check the further information of the file error ✐ T he preview image will not appear when the option is set "Display OFF".(+p.121) 1. Click Start button to start the auto-display. The image in the selected folder or program is displayed on the projector's screen.
Chapter 9 Network Viewer functions Error information Error type Description File Error It is displayed when the projector cannot acquire the correct file images from the FTP server, or when the master projector is turned off during the multi-control. Click Error button to check the details. Connection Error I t may be displayed when the slave projector is using the Network Viewer or Capture function during the multi-control.
Using the network viewer function Display length Repeat times 2 Select "Display mode" and press SELECT button, and then select "Auto" or "Manual" and then press SELECT button. When selecting "Auto", set "Display length", "Endless play" and "Repeat times" 3 Select "Connect" and then press SELECT button to start displaying. The images in the FTP server are displayed on the screen. ✐ I t enables you to browse the images by using the control buttons (s,t) on the remote control or on the projector.
Chapter 9 Network Viewer functions Use of the projector as FTP server You can use the projector in which a USB memory is inserted into the USB terminal as an FTP server. By using it as an FTP server, you can save the projection data that is converted by Network Viewer 5 [File Converter1, File Converter2] on the USB memory, and project the data with the Network viewer function in this projector or the other projectors. Copy the data for projections to the projector which is put USB memory in.
Use of the projector as FTP server Output the converted file directly to the projector with the USB memory. The file converted by Network Viewer 5 [File Converter 1] can be output directly to the projector with the USB memory. Refer to the "Creating the available data" for details of Network Viewer 5 [File Converter 1]. (p.114) Specify "FTP server" as an output destination of the converted file in the "Option" dialog of Network Viewer 5 [File Converter 1]. FTP server Host name.................
Chapter 9 Network Viewer functions 132
Chapter 10 10.
Chapter 10 Appendix Use of telnet You can control the projector by using the telnet application*1 installed on your computer. Normally, the telnet application is available on your computer. * The telnet 10000 port is used to control the projector. Control (For example, in case of using the telnet application of the Windows XP Professional.) 1. Select Run... submenu from Start menu on the computer. Type "telnet" onto the Open text area on the displayed window and press OK button. 2.
Use of telnet 4. Type the commands, refer to below table, to control the projector and then press "Enter" key for termination. For example, type "C00" which is a command to turn on the projector, and press "Enter" key. Confirm the projector is turning on. * Enter with ASCII 64-byte capital characters and one-byte characters. To disconnect the communication, press "Ctrl" key and "]" key at the same time, type "close" and then press "Enter" key on the Keyboard.
Chapter 10 Appendix Web browser setting This product is designed to enable the projector to be set up and controlled from an Internet web browser. Depending on the preference settings of the web browser, some control functions may not be available. Please make sure that the following functions are set up properly in the web browser. Active Script/JavaScript enable There are some control items used with the JavaScript function in the setting pages.
Web browser setting Examples: OS/Browsers Windows XP Professional Internet Explorer v.6.0 ActiveScript setting Select Internet Options from Tools menu on the web browser and then select Security tab and click Customize Level… button. On the security setting window, scroll down and find the Scripting item, make sure that "Enable" is selected in item Active Scripting.
Chapter 10 Appendix Flash Player Add-on setting Select Manage Add-ons... from Tools menu on the web browser. Select "Add-ons currently loaded in Internet Explorer" from Show pull-down menu. Make sure that the "Shockwave Flash Object" is listed under the item "Enabled". Proxy setting Select Internet Options from Tools menu on the web browser and then select Connection tab and click LAN Settings button.
Web browser setting Netscape Navigator v.7.0 JavaScript Setting Select Preference from Edit menu on the web browser and then select the item Advanced/ Scripts & Plugins in the Category column. Make sure that the Enable JavaScript for Navigator is checked. Flash Player enable Flash Player Plug-in setting Select About:Plug-ins from Help menu on the web browser. The plug-ins software provided on the browser are listed on the page.
Chapter 10 Appendix Proxy setting Select Preference from Edit menu on the web browser and then select the item Advanced/ Proxies in the Category column. Properly set up your web browser's the proxy server settings according to the local area network environment to which the projector is connected. - Using proxy server When you use an external internet connection from the local area network, select the item Manual proxy configuration.
Firewall setting Firewall setting If you use Windows XP SP2 or Windows Vista and using Network Capture 5, you may see the Windows security warning dialog as below. In that case, click "Cancel the block" button on the dialog to enable the function of Network Capture 5. (This page is described with Windows XP screen the example.) Even if you select "Block", you can cancel the blocking following to the steps below; 1 Open Control Panel form Start menu and double-click Windows Firewall icon.
Chapter 10 Appendix Troubleshooting If you have any trouble in setup or operation of the projector, refer to the troubleshooting items and check the relevant matters described. ■ The computer cannot connect projectors. Wired LAN Is the LAN cable connected to the projector properly? Is the LAN setting of the projector set “On”? See “Wired LAN setting” in the projector menu.
Troubleshooting Infrastructure Mode: When selecting Wireless 5 (factory default setting) Check each item below in the Wireless Setting menu of the projector as follows: *IP Address............................... No setting is required. *Sub net.................................... Should be the same as the setting of the access point *Gateway.................................. Should be the same as the setting of the access point *Network Type........................
Chapter 10 Appendix ■ Although the connection between PC and the projector is established, images are not projected on the screen. Make sure Wireless/Wired is selected from the Input source menu of the projector. ■ Cannot be turned on/off with the web browser. Make sure the settings of the projector are correct to use the projector with it. Set the item Standby mode to "Network" from Main menu ➔ Setting menu. Refer to “7. Controlling the projector” ➔ “ Power control and status check” (☞p.68).
Troubleshooting ■ Projector does not reproduce the computer's sound during the real time capturing. To reproduce the sound in the projector correctly, follow the procedures below; • Start up the real time capture and then start up the movie player software. • Terminate the movie player software first and then terminate the real time capture. Check that the "PJ Virtual Audio Device" is selected on the audio device panel of the computer.
Chapter 10 Appendix File Converter 1 ■ What kind of image formats can I convert? T he File Converter 1 makes it available to convert into the JPEG format from the following image formats. Bitmap format (.bmp) JPEG format (.jpeg .jpg) Microsoft power point format (.ppt) File Converter 2 ■ Sometime I have the white frame images converted by the File Converter 2? It may have images with white frame due to the paper margin of the print driver depending on the image data.
Troubleshooting Auto Capture ■ I have deleted the AutoCapture program file on the supplied USB memory. I want to perform the AutoCapture with a commercially available USB memory. To perform AutoCapture, you should have all files and folders of "Auto Capture" folder on ‘Network Viewer & Capture 5 (CD-ROM)’ on the root of USB memory. By copying or drag and dropping those files and folders on the root of a commercially available USB memory, you can perform the AutoCapture as well as a supplied USB memory.
Chapter 10 Appendix Terminology DHCP server (Dynamic Host Configuration Protocol) It is necessary to set an IP address for each computer or equivalent equipment when a network is established by TCP/IP. If there exists DHCP server on the network, it will assign IP addresses to client computers every time they request it. If there exists equipment with DHCP server functions (such as a Windows 2000 server and a dial-up router) on the network, the DHCP server function may be automatically operating.
Terminology Wi-Fi Alliance (Formerly Name: WECA (Wireless Ethernet Compatibility Alliance)) It is an organization that aims to promote the spread of Wireless LAN, and it guarantees the interoperability of products that meet the Wireless LAN standard. WPS (Wi-Fi Protected Setup) It is a standard to easily perform security of the wireless LAN which Wi-Fi Alliance devised. There are two kinds of WPS configuring which is push button type and PIN code type.
U.S.A. Canada EIKI International, Inc. 30251 Esperanza Rancho Santa Margarita CA 92688-2132 U.S.A. Tel : 800-242-3454 (949)-457-0200 Fax : 800-457-3454 (949)-457-7878 E-Mail : usa@eiki.com EIKI CANADA - Eiki International, Inc. P.O. Box 156, 310 First St. - Unit 2, Midland, ON, L4R 4K8, Canada Tel : 800-563-3454 (705)-527-4084 Fax : 800-567-4069 (705)-527-4087 E-Mail : canada@eiki.
