Pj-to NetDirector Model No. PjNET-15 Preparation Installation ER Basic Setting and Operation POW Controlling the Projector Controlling the Multi-Projectors Use of Serial Port Appendix INSTALLATION and OPERATION of the Pj-to NetDirector This Pj-to NetDirector is an optional product to control and set up a projector via a network. Attach this product to the projector and connect a network cable.
Preparation Compliance Federal Communication Commission Notice This equipment has been tested and found to comply EIKI PjNET-15 with the limits for a Class B digital device, pursuant to Tested To Comply part 15 of the FCC Rules. These limits are designed With FCC Standards to provide reasonable protection against harmful interference in a residential installation.
Preparation Expression/Abbreviation The following abbreviations may appear in this manual: ● Windows 95, Windows 98, Windows 2000, Windows Me, Windows XP, Windows NT4.0 ➜ Windows ● Macintosh, Power Macintosh ➜ Macintosh ● Mac OS 8 or later ➜ Mac OS In some cases, the “Pj-to NetDirector” is explained as “this product” or “Network Unit” in this manual. The word “projector” found in this manual means “projector provided with Pj-to NetDirector” unless otherwise noted.
Contents Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Expression/Abbreviation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Operating Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Flow of installation . . . . . . . . . . . .
Contents SYSTEM Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 Image Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Sound Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Screen Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 How to set the Timer . . . . . . . . . . . . . . . . . . . . . . . . .
Preparation Features Web Management function With this function, you can monitor projector functions such as power status, lamp status, input mode, signal condition, lamp-use time, etc. through the network by using the web browser installed on your computer. Power ON ! E-Mail Alert function Projector (Network Unit) sends messages to the registered e-mail addresses when a lamp abnormality or power failure occurs with the projector. In this message, it describes how to solve the cause of the problems.
Features Multi-control function A single computer can control and set up the multiple computers at the same time. 5th floor Theaters 3rd floor Meeting Room Automatic On/Off using Timer function Automatically turn on or off the projectors at specified date/day and time by using the clock function. Now it’s 11:30 I’m ready to turn ON, and select Computer 1. Control port ready for external equipment via network ENGLISH This product provides a serial port (RS-232C) for controlling external equipment.
Preparation Operating Environment To perform the management and setting up the projector using this product, the environment described below is required. Operating System Windows 95 / Windows 98 / Windows 2000 / Windows Me / Windows NT / Windows XP Mac OS 8.0 or later Network Network must handle Ethernet correctly and accept TCP/IP protocol. Computer The computer must provide a 10Base-T or 100Base-TX network card. Web browser application* ● Microsoft Internet Explorer version 5.
ENGLISH Installation 1 Network Unit OWNER’S MANUAL 9
Installation Flow of installation The following are instructions for attaching this product to the projector and connecting it to the network. Please review the entire procedure to become familiar with it. 1 Check package Please check the contents of a package. This product contains a Network Unit and an owner’s manual (this manual). Also please check the name and function of each part (p.11). 2 Installation (p.12-14) 1. Mount this product onto the projector. 2.
Name and function of each part Name and function of each part Power indicator This illuminates red when the Network function is set ON in the projector menu. ER POW LAN port Connecting the LAN cable. (p.13) Serial port This is used when controlling the external equipment via the network. (p.57) Connector plug Connect to the DVI terminal on the projector. (p.12) Computer Input Terminal Use as the Computer 2 RGB analog input terminal. (p.
Installation [1] Mounting 1 Disconnect the AC plug from the projector. 2 Remove all of the hole covers (3 round type, 4 square type) on the rear of the projector and insert plug on this product to the DVI connector. Mount the unit as the switch lever on the unit presses the mount detecting switch on the projector. switch lever 3 Tighten three screws by using a hole covers Mount detecting switch coin etc.
Connection of LAN cable [2] Connection of LAN cable To connect to the network, it is required to use the UTP (Unshielded Twisted Pair) strait cable with RJ-45 plug. There are two different types of cables depending on whether the network is constructed with 10Base-T or 100Base-TX. Prepare the Hub (10Base-T or 100Base-TX) to distribute the network cable if required. 1 Disconnect the AC plug from the projector. 2 Connect the UTP strait cable to the LAN port on the Network Unit.
Installation [3] Confirmation of network menu activity When installing this product onto the projector, the network on-screen menu items for this product are activated automatically. If not activated, the product may not have been installed correctly. Please check chapter “Mounting” on page 12. Turn on the projector and display the menu on the screen.
Network configuration [4] Network configuration When you connect a projector to a network, the network number of projector must be the same as the network you intend to connect. You should configure projector’s network first. Make sure that the projector is connected to the network correctly. There are 2 ways to configure the network, by using the [A] projector’s menu, or by using the [B] computer . Refer to the chart below and use the method you prefer.
Installation A Configure the network with the projector This example explains how to set the following configuration. IP Address Subnet Mask Default Gateway DNS : 192.168.1.201 : 255.255.255.0 : 192.168.1.1 : 0.0.0.0 1 Selection of network menu [Network] Turn on the projector and display the menu on the screen. Select the Network icon from the Setting sub menu using the pointers, and then press the SELECT button on the remote control or on the projector. Confirm that its mode is set On.
Network configuration How to enter the numbers To move the selection and change the values, Use the pointers ▲/▼/7/8 on the projector or on the remote control unit. The 7/8 keys are used to move the selection item. The ▲/ ▼ keys are used to change the number value. 3 Restart the Network Unit Select the SET with the 7/8 keys and press the SELECT button again. The network configuration display disappears and the Network Unit begins restarting*1. It takes about 60 seconds.
Installation B Configure the network with the computer This example explains how to set the following configuration. IP Address Subnet Mask Default Gateway DNS : : : : 192.168.1.201 255.255.255.0 192.168.1.1 0.0.0.0 The default network configuration is set as follows. IP Address Subnet Mask Default Gateway DNS : 192.168.0.2 : 255.255.255.0 : 0.0.0.0 : 0.0.0.0 ER POW Make sure that the projector is connected to the network and then connect the AC cord to the outlet.
Network configuration 2 Configure the network of the projector by using the web browser. 1. Enter the IP address of the projector as the URL. The login page will be displayed and login. For further information, please see chapter “2: Basic Setting and Operation” on page 25. 2. Configure the network through the setting page on the browser. For further information, please see chapter “Network Configuration” on page 31. Completing of installation ENGLISH Now the installation is completed.
Installation Configure the network of computer When you use the projector through the network, the IP address of the projector must be the same IP network number of the existing network. Also it is required to use the same IP network number of the computer to set up the projector. In the network included with the gateway (router), it must be used with the IP network number specified by the gateway (router).
Configure the network of computer Windows 2000/NT4.0 This example explains how to set the following network address. IP Address : 192.168.0.5 Subnet Mask : 255.255.255.0 Gateway Address : 192.168.100.1 1 Select 2 3 4 5 the Network and Dial-up Connections menu from [Start] - [Settings] menu. Click the Local Area Connection icon with right button of the mouse and then select the Properties menu from the popup menu. The right window will appear on the screen.
Installation Windows XP This example explains how to set the following network address. IP Address : 192.168.0.5 Subnet Mask : 255.255.255.0 Gateway Address : 192.168.100.1 1 Select 2 3 4 5 the Control Panel menu from the [Start] menu. Click the Network and Internet Connection and then click the Network on the control panel. Click the Local Area Connection icon with right button of the mouse and then select the Property menu. The right window will appear on the screen.
Configure the network of computer Macintosh This example explains how to set the following network address. IP Address : 192.168.0.5 Subnet Mask : 255.255.255.0 Gateway Address : 192.168.100.1 1 Select 2 3 4 TCP/IP* 1 menu from the [Apple] - [Control Panel] menu. Select Ethernet from the "Connect via" pull down menu and Manually from the "Configure" pull down menu of the TCP/IP Control Panel. Enter the IP Address*2 and Subnet Mask. Enter the Router Address.
Installation Notice about system construction For installation of multiple projectors into the same network with Network Unit. Do not install multiple projectors with the Network Units that have their default network settings to the same network. The use of the Network Units which have the default IP address set to the same network settings will cause IP addresses to collide and create a malfunction. When you install multiple projectors into the same network, configure the network with the following steps.
ENGLISH Basic Setting and Operation 2 Network Unit OWNER’S MANUAL 25
Basic Setting and Operation This chapter describes basic operations and settings for controlling the projector via a network using this product. It is required that computer and projector are connected to the network and the network address be properly configured. Login or logout the setting page of the projector 1 Enter the IP address Launch the web browser installed in your computer, enter the IP address into the "Address" on the browser and the press the “Enter” key.
Login or logout the setting page of the projector 3 Display of main setting page The following main setting page of the projector is displayed. Perform the various kinds of setting through this page. Click on the linked text to display the control and setting pages. ☛ The main menu which can be set up and control the projector appears on the left upper side of the page. ☛ The projectors connected to the network are listed on the left lower side of the page.
Basic Setting and Operation 4 Logout Click on the Log Out linked text on the main menu. The web browser will logout from the setting page and displays the login page automatically. [Important] If you check the "Save this password" item at the login page, the saved password will be cleared when logout is performed. In environments where the setting computer is used by several people, it is recommended for security reasons that personnel logout or not save the password at the login page.
Initial Setting 2 Date/Time Setting Set present date and time by using the pull down menu buttons and press each Set button. Confirm that the date and time are set correctly. The displayed date and time are not updated automatically, press the Refresh button to get the current date and time. This page is to set the password to restrict the access from an unauthorized person through the network. Enter the password onto the text box and press the Set button.
Basic Setting and Operation 4 Temperature unit setting Change the temperature unit displayed on the Power & Status page by using the pull down menu.
Network Configuration Network Configuration Click on the Network Setting linked text on the main menu. The following setting page is displayed. This page is to set the IP Address, Subnet Mask, Default gateway, DNS (Domain Name Server) and projector name. 1 Configure the network The IP address and Subnet Mask have been configured already in chapter “Installation”. If you want to change them or configure default gateway*1 or DNS*2, perform them in this page.
Basic Setting and Operation E-mail Setting This product has an E-mail function which can send an alert message to users or an administrator if it detects an abnormality on the projector or run out of the life span of the lamp. Click on the E-Mail Setting linked text on the main menu and follow the below steps. 1 SMTP Server*1 Type the address of SMTP server for E-mail and press the Set button. 2 Administrator Address Type the E-mail address of administrator and press the Set button.
E-Mail setting 4 Condition selection for sending alert message Check the condition items under which alert messages will be sent and press the Set button. Please refer to chapter “Examples :Type and contents of alert messages” described on next page. Note: A free message can be sent when the lamp use time reaches the preselected lamp use time. Check the “lamp use time” and enter a setting time. Input a free message on the attached message text box and then press the Set button.
Basic Setting and Operation ● When the internal power circuit is failed: TITLE: Message from projector 01-01-2003 00:59 Projector Model Name: XG110/XG210 TCP/IP: 192.168.0.2 Projector Name: myProjector It sends you following massage. *The Projector lamp was turned off, because projector power circuit failed. Unplug the projector from AC outlet and ask servicing to qualified service personnel. ✐ The Projector lamp was turned off, because the projector power circuit failed.
ENGLISH Controlling the Projector 3 Network Unit OWNER’S MANUAL 35
Controlling the Projector Power on/off the projector Click on the Power & Status linked text on the main menu. The control page will be displayed. By Pressing the On or Standby button on the page, the power of the projector can be controlled. When you press the Standby button, another confirmation popup window*1 will appear, and then press the Yes button if it is set to standby. [Note] *1 This popup window is realized by using the JavaScript function of web browser.
Power on/off the projector Check the status of projector In the "Power & Status" page, you can control the projector power, and also you can check the status of the projector as follows: Items Accumulated lamp-use time Accumulated projector-use time Power status Projector condition Input status Internal temperature Description It displays in 1 hour units (h) When resetting the lamp counter, this time will be reset to 0. It displays the accumulated used time in an hour unit (h). This cannot be reset.
Controlling the Projector Control the projector Click on the Control linked text on the main menu. The control menu will be displayed on the lower side of the page. When you click each control icon, the control page is displayed according to the control menu you selected. ✐ Please see the owner's manual of the projector to have the further information of each control item.
Control the projector PC Adjustment This function is to adjust the signal from the computer connected to the projector to obtain the proper picture image on the screen. The available parameters and operation are listed below. Adjustment Items Auto PC adjustment Fine sync Total dots Position ENGLISH Comment Operation Press the Start button to start automatic adjustment. Press the - or + button repeatedly to adjust the fine sync.
Controlling the Projector SYSTEM Adjustment This function is to select the color system of video signal or scanning system of component signal input to the projector. Select a system with the radio buttons to match the color system or scanning system of input source, and then press the Set button. The available systems and operation are listed below.
Control the projector Image Adjustment Adjustment items Operation Image adjustment mode Select image mode among the Standard, Real **, Cinema*, Image1 to Image4 with pull down button menu . Image1 to 4 are user preset mode. Adjustment items Contrast, Brightness, Sharpness*, Gamma, White Balance, Color Temperature, Tint*, Color*, Noise Reduction*, Progressive* * Controls for video input, ** Controls for computer input Comment Type the comment in the text area and press the Save button.
Controlling the Projector Screen Adjustment This function is to adjust the screen mode of the projector. The setting items are switched automatically according to selected input mode, computer or video input. The adjustment items and operation are listed below. Adjustment items Aspect True* Digital Zoom* Operation Used to change the screen mode. Select the screen mode and press the Set button.
Control the projector Setting This function is to set up the projector. The value next to each setting represents the current status or mode. The setting items and operation are listed on the next page. ENGLISH Check if High speed control mode.
Controlling the Projector The setting items and their operations are listed below. Setting items Language Operation Select the language used in the on-screen menu of the projector. Select your desired language with the pull down menu button, and then press the Set button. Keystone Correct the distortion of the projected image with the Left, Right, Up and Down buttons. To cancel the keystone correction, press the OFF button.
Control the projector How to set the Timer This function is used to turn the projector off or on at a preselected day/date and time. Follow the below steps for setting. Day selection Event Date selection 1 Select a day or date To set the timer event at same time everyday, select "day" entry with radio button and then select desired day with the pull down menu button.
Controlling the Projector Getting the current time The displayed time is the value set when the setting page was displayed. This time value is not updated automatically. To update the display time press the Refresh button. Notes on timer setting ✐ Up to 10 timer events can be registered. Timer events always operate according to the next valid event depending on the projector's power status.
Control the projector Service This function sets the cooling fan speed of the projector. Set proper fan speed depending on the installation environment. Operation Select the Max or Normal with radio buttons and then press the Set button.
Controlling the Projector Save Actual Adjustment This function is to save and load the control values of the projector. The storable control items are Input, PC, System, Image and Screen controls, and these control items differ from each selected input mode and functions of the projector you use. 1 Adjust and set the controls Set the controls properly according to the selected source.
Control the projector’s menu To load the control set Display the Load Setting No. on upper part of the page. Select your desired set number with the pull down menu button and then press the Set button. The setting values of the selected set number are applied to the current settings. Example of setting Control the projector's menu Click on the Display Menu on the main menu. The following menu control page is displayed. This page is to control the on-screen display menu of the projector.
Controlling the Projector 50
ENGLISH Controlling the Multi-Projectors 4 Network Unit OWNER’S MANUAL 51
Controlling the Multi-Projectors Multi-Control This function enables control of multiple projectors equipped with the Network Units that are connected to the network at the same time. Click on the Multi Control linked text on the main menu to display the control page. Note: To control the multiple projectors, each projector must have the same password. Register IP address and projector name Enter the IP address of the projector onto the text box.
Multi-control [Note] *1 If the JavaScript setting of the web browser is set “JavaScript Disable”, The registered projector name will not be listed on the Change a Projector” sub menu, Please change the JavaScript setting. See chapter “Web browser setting/Active Script (JavaScript enable)” on page 68 for further instructions. * If you do not use the projector name, a word “None” will be displayed in the Name column.
Controlling the Multi-Projectors Load and apply the setting value The control sets saved for each projector (p. 48) can be used while the multi-controlled projectors function is being used. Select a setting number from the item Load Setting No. with the pull down menu button and then press the Set button. The control values stored with selected set number for each projector will be applied to the individual projector assigned to that set.
Control multi- projectors at the same time Status If some of the registered projectors are deactivated by some means (such as disconnecting the power source, disconnecting the LAN cable, disconnecting from the network), control changes will continue to be effective for the projectors that are still activated. At the same time, the deactivated projectors are excluded from the multicontrol, and they will be displayed with gray background color as shown below.
Controlling the Multi-Projectors Selection of another projector When you register the projectors for the multi-control, the IP addresses of the registered projectors are listed on the "Change a Projector" menu on the lower left side of the page. If each projector has a name, the projector name is indicated instead of the IP address. To register the projector name, see chapter "Exclude/Add the projectors from/into the multi-control" on page 53.
ENGLISH Use of Serial Port 5 Network Unit OWNER’S MANUAL 57
Use of Serial Port This product provides with a serial control port (RS-232C) to control the external equipment which has an RS-232C port. This function allows external equipment to be controlled by the computer through the network and the projector can be controlled by the external serial controller. Before connecting the external equipment, perform the setting “Serial port setting” described below. Serial port setting Set up the extra serial port of this product.
Serial port setting Setting to control the equipment connected to the serial port from the computer Serial Control Port Other Settings :Selects “External” :Sets according to the computer specified port no. Do not use port no. 10000*2. :Sets according to the communication condition of the equipment Setting to control the projector from the serial controller connected to the serial port Serial Control Port Other Settings :Selects “Projector” :Not specified. Do not use port no. 10000*2.
Use of Serial Port Control Examples Example 1 Controlling AV equipment through network DVD Player RS-232C serial cable Example 2 Controlling a projector which is not on the network function through network.
Use of Serial Port Example 3 Controlling the projector with the serial controller through the serial port (RS-232C). Serial Controller ENGLISH RS-232C serial cable ✐ When connecting the peripheral equipment to this Network Unit, you should notice the type of serial cables. This product provides a reverse (cross) type of serial port. When connecting the peripheral equipment, please use an optimum serial cable according to the polarity of the port on the equipment.
Use of Serial Port Use of Telnet The following is a control example of external equipment connected to this product by using the telnet application*1 installed on your computer. The telnet application is needed to use commands*2 which controls the external equipment. Preparation 1 Disconnect AC plug from the projector and connect an external equipment to the extra serial port with an RS-232C serial cable. 2 Turn the projector and external equipment on.
Use of telnet 3 The following window will appear. Type as follows and then press the Connect button. Host name : 192.168.0.2 (type projector IP address) Port : telnet or 23 Terminal type : vt100 4 When communication is established, the word "PASSWORD:" appears on the window. Type the login password* for the projector and then press the "Enter" key on the keyboard. If you do not register the login password, just press the "Enter" key. When the word "Hello" is replied, login has been successful.
Use of Serial Port Control the projector with Telnet This product allows you to control the projector by using the Telnet application. Normally, it is used to control the external equipment connected to the serial port and also control the projector itself by specifying the telnet port no.10000. Specify port no. 10000 as the right on the serial port setting page. This function does not depend on other setting items. In the setting of the computer, specify the port no.
Appendix:A 6 ENGLISH Connection examples Web browser setting Technical data Network Unit OWNER’S MANUAL 65
Appendix Examples of Connection Peer-To-Peer connection Connect the projector (PJ01) to the control computer (PC05) directly Computer Name: PC05 IP Address Subnet Mask Default Gateway DNS : 192.168.0.5 : 255.255.255.0 : : Projector Name: PJ01 IP Address Subnet Mask Default Gateway DNS : 192.168.0.2 : 255.255.255.0 : 0.0.0.0 : 0.0.0.0 * UTP cross cable Connect the projector (PJ01) to the control computer (PC05) via the hub. Hub Computer Name: PC05 IP Address Subnet Mask Default Gateway DNS : 192.
Examples of connection The gateway (Router) installed in the network Connect the projector (PJ01) to the control computer (PC05) via the gateway. Theater Computer Name IP Address Subnet Mask Default Gateway DNS : PC205 : 192.168.200.5 : 255.255.255.0 : 192.168.200.1 : 192.201.1.5 Projector Name: PJ01 IP Address Subnet Mask Default Gateway DNS : 192.168.200.15 : 255.255.255.0 : 192.168.200.1 : 192.201.1.5 Hub Network Group: 192.168.200.0 Gateway (Router) To another network IP Address : 192.168.200.
Appendix Web browser setting This product is designed enable the projector to be set up and controlled from an Internet web browser. Depending on the preference settings of the web browser, some control functions may not be available. Please make sure that the following functions are set up properly in the web browser. Cookies enable This is to enable the auto-login function in the login page.
Appendix Setting examples: OS/Browsers Windows 95/98 Internet Explorer v.5.5 Cookies setting Select the Internet Options menu from the Tool menu on the web browser and then select Security tab and press the Customize Level… button. On the security setting window, scroll down and find the Cookies item, make sure that the “Enable” is selected in the item Allow cookies that are stored on your computer.
Appendix Proxy setting Select the Internet Options menu from the Tool menu on the web browser and then select Connection tab and press the LAN Settings button. Properly set up your web browser's the proxy server settings according to the local area network environment to which the projector is connected.
Appendix Netscape Navigator v.4.7 Cookies setting Select the Preference menu from the Edit menu on the web browser and then select the item Advanced in the Category column. Make sure that the Allow all cookies is checked in the Cookies column. JavaScript Setting ENGLISH Select the Preference menu from the Edit menu on the web browser and then select the item Advanced in the Category column. Make sure that the Enable JavaScript is checked.
Appendix Proxy setting Select the Preference menu from the Edit menu on the web browser and then select the item Advanced/Proxies in the Category column. Properly set up your web browser's the proxy server settings according to the local area network environment to which the projector is connected. - Using proxy server When you use an external internet connection from the local area network, select the item Manual proxy configuration and press the View button. The proxy setting window will appear.
Appendix Mac OS 8.6 Internet Explorer v.5.0 Cookies setting Select the Preference menu from the Edit menu on the web browser and then select Cookies under the Receiving Files heading the preference settings window. Make sure that the Never ask is selected in the item When receiving cookies. ActiveScript setting ENGLISH Select the Preference menu from the Edit menu on the web browser and then select Web Content under the Web Browser heading the preference settings window.
Appendix Proxy setting Select the Preference menu from the Edit menu on the web browser and then select Proxies under the Network heading the preference settings window. Properly set up your web browser's the proxy server settings according to the local area network environment to which the projector is connected. - Using proxy server When you use an external Internet connection from the local area network, check the item Web Proxy and enter the proxy server address correctly.
Appendix Netscape Navigator v.4.7 Cookies setting Select the Preference menu from the Edit menu on the web browser and then select the item Advanced in the Category column. Make sure that Accept all cookies is checked in the Cookies column. JavaScript Setting ENGLISH Select the Preference menu from the Edit menu on the web browser and then select the item Advanced in the Category column. Make sure that Enable JavaScript is checked.
Appendix Proxy setting Select the Preference menu from the Edit menu on the web browser and then select Proxies under the Advanced heading in the Category column. Properly set up your web browser's the proxy server settings according to the local area network environment to which the projector is connected. - Using proxy server When you use an external Internet connection from the local area network, select item Manual proxy configuration and press the Configure button.
Specifications Product specification Type ......................................Pj-to NetDirector LAN interface ........................Applicant regulation IEEE802.3 (10Base-T) IEEE802.3u (100Base-TX) Data transfer speed 10Mbps/100Mbps data transfer mode Half duplex/Full Duplex Terminal 8-pin modular (RJ-45) Network protocol ..................TCP/IP specification TCP/IP Serial interface ......................RS-232C Baud rate 0.3/1.2/2.4/4.8/9.6/19.2/28.8/57.6/115.
Appendix Port Specification LAN port specification 8-pin modular connector (RJ-45) 12 3 4 5 6 7 8 pin No. Signal 1 2 3 4 5 6 7 8 TX+ TXRD+ (not used) (not used) RD(not used) (not used) Function Transfer data (+) Transfer data (-) Receive data (+) Receive data (-) Serial port specification D sub 9-pin connector (RS-232C) 5 4 9 Pin No.
Appendix Computer Input port specification HDB 15-pin connector (VGA) 10 15 14 2 3 9 8 13 1 7 12 6 11 Pin No. Signal 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 R G B MONITOR ID2 GND(H) GND(R) GND(G) GND(B) +5V GND(V) MONITOR ID0 DDC DATA H V DDC CLK Function R input G input B input MONITOR ID2 Ground(Horiz.) Ground(R) Ground(G) Ground(B) 5V Power Supply Ground(Vert.
Appendix 80
ENGLISH Appendix:B FAQ Network Unit OWNER’S MANUAL 81
Appendix FAQ Installation/Access Q Why doesn’t the setting page appear in my web browser? A Following causes are possible. Please check them. 1. The projector does not connect to the network. Check LED indicators status (p.11). - Check the connection of LAN cable if the LINK indicator does not illuminate orange. - Check the network configuration of the projector if ACT indicator does not illuminate green. 2. Function “Network” in the projector is not set to“ON”.
Appendix 3. Enter the projector’s IP address [192.168.0.2] at the “Address” column on the Web browser. [Note] Make sure that the proxy setting of your web browser is set “Not use a proxy server”. See further information on page 68. 4. If the login page appears, this product is operating properly. The problems may be in the network configuration of the computer or in the network. Please try to set up the network by following chapter “Network configuration” (p.15).
Appendix Q How can I install several projectors equipped with the Network Unit? A Install and configure network one by one to avoid the IP address collision each other (p.24). To configure the IP address please see chapter “Network configuration”(p.15). Q How many projectors can I control with multi-control function? A It has been designed to control up to 100 sets but it depends on the network environment.
Appendix Q Can I register the setting page as a web browser “Favorites” or “Bookmarks”? A Please add the “Login” page to your “Favorites” or “Bookmarks”. Do not add the specified setting page because it will not be able to perform the password authentication correctly. Q Why does the following password authentication window sometimes appear at login? Depending on the web browser application type, version or OS you are using, the authentication window may appear.
Appendix Operation Q Why can't I change the controls in the setting page with web browser? A Please make sure the projector is turned on. If it is in the standby mode, the setting is not effective to the projector. To control the projector with a web browser, the projector must be in the powered-on condition. Also, projectors registered for multi-control cannot have any controls changed if they are in standby mode. But timer and clock settings are always effective, even for projectors in standby mode.
Appendix Q Why am I not receiving E-mail alert messages? A Make sure that the registered E-mail address and SMTP server address are correct. If the SMTP server is located in your LAN (Local Area network), the address should be set to the SMTP server in your LAN. The SMTP server located outside of your LAN may not be available for security reason. For further information please contact your network administrator (p.32). It may be required for the authentication depending on the SMTP server.
Appendix Q What are the rules for IP address assignment? If the network is constructed with TCP/IP protocol, a unique IP address is required for each piece of network equipment. The following are basic rules of the assignment. Rule1 Do not configure the same IP address to the network equipment in the same network group. Each piece of equipment must be assigned a unique IP address. If the IP address is set [192.168.x.x], the Subnet Mask should be set [255.255.255.0] for example.
ENGLISH Appendix Network Unit OWNER’S MANUAL 89
A-key to better communications U.S.A. Canada EIKI International, Inc. 30251 Esperanza Rancho Santa Margarita CA 92688-2132 U.S.A. Tel : 800-242-3454 (949)-457-0200 Fax : 800-457-3454 (949)-457-7878 E-Mail : usa@eiki.com EIKI CANADA - Eiki International, Inc. P.O. Box 156, 310 First St. - Unit 2, Midland, ON, L4R 4K8, Canada Tel : 800-563-3454 (705)-527-4084 Fax : 800-567-4069 (705)-527-4087 E-Mail : canada@eiki.
