Anleitung_BT_FW_100_GB_SPK7__ 13.03.13 13:12 Seite 1 Original operating instructions Flux Cored Welding Set Art.-Nr.: 15.752.20 I.-Nr.
Anleitung_BT_FW_100_GB_SPK7__ 13.03.
Anleitung_BT_FW_100_GB_SPK7__ 13.03.
Anleitung_BT_FW_100_GB_SPK7__ 13.03.13 13:12 Seite 4 10 11 2. S 1. 3. 4.
Anleitung_BT_FW_100_GB_SPK7__ 13.03.
Anleitung_BT_FW_100_GB_SPK7__ 13.03.
Anleitung_BT_FW_100_GB_SPK7__ 13.03.13 13:12 Seite 7 GB Table of contents: Page 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
Anleitung_BT_FW_100_GB_SPK7__ 13.03.13 13:12 Seite 8 GB Important! When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care. Keep this manual in a safe place so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well.
Anleitung_BT_FW_100_GB_SPK7__ 13.03.13 13:12 Seite 9 GB 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. welding. These offer protection from electric shocks (idling voltage in the welding circuit), harmful radiation (Heat and UV radiation) and from glowing metal and slag spatter. Wear firm, insulated footwear. Your shoes should also protect you in wet conditions. Opentoed footwear is not suitable since falling droplets of glowing metal will cause burns. Wear suitable clothing, do not wear synthetic clothes.
Anleitung_BT_FW_100_GB_SPK7__ 13.03.13 13:12 Seite 10 GB protected. Unauthorized persons are to be kept away from the welding work. 2. The walls in the immediate vicinity of stationary workplaces should not have a light color or a sheen. Windows up to head height are to be protected against radiation passing through them or reflecting off them, for example by coating them with a suitable paint. Do not store or use the equipment in wet conditions or in the rain. Use the equipment only indoors. 2.
Anleitung_BT_FW_100_GB_SPK7__ 13.03.13 13:12 Seite 11 GB 5. Before starting the equipment 5.1 Assembly (Fig. 7-13) 5.1.1 Fitting the carrying strap (1) n Guide the carrying strap (1) through the slit on the rear of the equipment, over the housing cover (3) and through the slit on the front of equipment. Connect the ends of the carrying strap as shown in Figure 5 and adjust the strap to the required length.
Anleitung_BT_FW_100_GB_SPK7__ 13.03.13 13:12 Seite 12 GB n n n n n n n n n two guide grooves. Turn the feed roller (G) over if necessary or replace it. (Fig. 19). Position the feed roller holder (F) again and secure it. Remove the gas nozzle (Fig. 2/10) from the burner (Fig. 2/11) by turning it clockwise, unscrew the contact tube (Fig. 3/15). (Fig. 2 – 3). Place the hose package (Fig. 1/9) on the floor as straight as possible pointing away from the welding set.
Anleitung_BT_FW_100_GB_SPK7__ 13.03.13 13:12 Seite 13 GB When the arc is burning, the welding set will feed wire into the weld pool. When the weld nugget is large enough, move the burner slowly along the required edge. Move it to and fro if necessary to enlarge the weld pool a little. Find the ideal setting of the welding current and wire feed speed by carrying out a test weld. Ideally an even welding noise will be audible.
Anleitung_BT_FW_100_GB_SPK7__ 13.03.13 13:12 Seite 14 GB 9. Troubleshooting Fault Feed roller does not turn Cause Remedy Power supply not connected Check connection Wire feed controller set to 0 Check setting Feed roller turns, but does not feed Incorrect roller pressure (see 5.3.3) Check setting any wire Roller brake set too firmly (see Check setting 5.3.3) Dirty / damaged feed roller (see 5.3.
Anleitung_BT_FW_100_GB_SPK7__ 13.03.13 13:12 Seite 15 GB 10. Key to symbols EN 60974-1 European standard for arc welding sets and welding power supplies with limited on time Do not store or use the equipment in wet or damp conditions or in the rain.
Anleitung_BT_FW_100_GB_SPK7__ 13.03.13 13:12 Seite 16 t For EU countries only Never place any electric tools in your household refuse. To comply with European Directive 2002/96/EC concerning old electric and electronic equipment and its implementation in national laws, old electric tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.
Anleitung_BT_FW_100_GB_SPK7__ 13.03.13 13:12 Seite 17 The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of ISC GmbH.
Anleitung_BT_FW_100_GB_SPK7__ 13.03.
Anleitung_BT_FW_100_GB_SPK7__ 13.03.13 13:12 Seite 19 t GUARANTEE CERTIFICATE Dear Customer, All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. Of course, if you would prefer to call us then we are also happy to offer our assistance under the service number printed below.
Anleitung_BT_FW_100_GB_SPK7__ 13.03.
