ENG INSTALLATION MANUAL i500 Multiroom Audio System
i500 Multiroom Audio System 1.- Description and components of the i500 Series 3 2.- Pre-installation: previous recommendations 6 2.1.- Power Source 2.2.- Communication Line 2.3.- Line Reinforcement Module 2.4.- FM Tuners 2.5.- Coverage of Remote Control Unit 6 6 6 7 7 3.- Installing the Master Unit 9 3.1.- Connection to Communication Line 3.2.- Connection to Universal Dock for iPod 3.3.- Connection to External Sound Sources 9 10 10 4.- Installing Speakers in each zone 13 4.1.
1. Description and components of the i500 Series The i500 is a multi-room audio system for listeners to enjoy music throughout the entire home by integrating the sound into the home’s fixtures. Thanks to its built-in ceiling speakers, the i500 series eliminates the need to have portable MP3 players or stand-along systems in each room. The Serie is also equipped with intercom features for room-to-room communication, electronic baby monitors, etc.
i500 Multiroom Audio System The Main Speaker (ref. 551 01) integrates the control and sound electronics of each zone or room and is equipped with the following basic features: FM tuner with built-in RDS, 30 memories and 75 ohm RF coaxial antenna connector wireless data and sound communication with Remote Control Unit data and sound (4 channels) input line from the Master Unit: 8 wires 5+5W sound amplifier built-in 8 ohm two-way loudspeaker 8 ohm output for Passive Speaker (ref.
The entire system is managed from Remote Control Units. They do not require any installation. The Remote Control Unit Base needs be connected to the mains. It acts as the Remote’s platform as well as providing battery charge for the Remote Control Unit: graphic interface with 2.2” color TFT built-in microphone 3.5 mm input jack for external sound source wireless data and sound communication with Main Active Speaker (ref.
i500 Multiroom Audio System 2. Pre-installation: previous recommendations The i500 Series requires basic pre-installation. To avoid future issues and ensure optimal system operation, follow these recommendations. 2.1. Power Source Main Speakers (ref. 551 01) and Auxiliary Speakers (ref. 552 01) must be connected to the 2 mains through wires with PVC isolation according to IEC60227 (H05VV-F 3G 0,75mm ) or 2 alternatively with synthetic rubber according to IEC60245 (H05RR-F 3G 0,75mm ).
In a bus-type system it should be installed in one or both ends of the system (see the figure). In star or mixed type systems look for the longest straight path between two points and install the device on one or both ends of the system. installation length 0..100m 100..200m 200..600m 2.4. # Main Active Speakers # Line Reinforcemen Devices 0..10 10..20 20..
i500 Multiroom Audio System The Main Speaker (ref. 551 01) is visually recognized from the rest of the Speakers by the antenna capsule and the blue LED integrated in the front grille. The location of the remaining Speakers (Auxiliary Speakers ref. 552 01 and Passive Speakers ref. 553 01) does not affect the coverage of the Remote Control Unit. To facilitate communication between the Remote Control Unit and the Main Speaker or Zone Controller follow all the recommendations in section 8.
3. Installing the Master Unit 3.1. Connection to Communication LINE The Master Unit is connected to the communication line by means of a Line Connector module (ref. 573x1). The cable supplied with the Master Unit must be specifically used for this connection. The Line Connector module is available in several colours and can be fitted with the most popular electrical switch brands by using the adapters listed in the EISSOUND catalog (BJC, Jung, Legrand, Niessen, Schneider, Simón, bTicino, ...).
i500 Multiroom Audio System 3.2. Connection to Universal Dock for iPod To access music stored in an iPod, the Master Unit is equipped with a back panel connection to the Universal Dock for iPod. The connection is only available with this Unit and should not used for any other purpose. LINE L1 L2 FM Pod LEVEL PORT LEVEL IR ! 3.3. Connection to External Sound Sources On its back panel, Master Unit is equipped with 2 RCA inputs to connect 2 external sound sources as L1 and L2.
LINE OUT L R For example, the PC audio output can be used to make the PC as a music server. ! audio out This way, also can be connect an Airport® and receive music from an iPhone® or iPad®.
i500 Multiroom Audio System (2) In systems equipped with a REC OUT (such as HI FI systems), connection to the Master Unit can be installed between the REC OUT and the music system’s amplifier. TAPE L R OUT IN REC L R IN OUT (3) The headphone output can be used in systems with no LINE OUT or REC OUT (such as walkman, compact stereos, MP3 players …).
4. Installing Speakers in each zone 4.1. Zone with Main Speakers (basic installation) The choice of the location of the Main Speaker is VERY IMPORTANT. Please follow all the recommendations indicated in section 2.5. L N 230V Each Main Speaker (ref. 551 01) requires simple installation as per the following diagram. 55301 230V L N ANT 55101 Yellow 4 Green 4 Blue AUX Orange Brown Violet Black White 4.2.
L N 230V Multiroom Audio System i500 14 55301 55301 55301 230V 230V 230V L L L N N N ANT 55201 55101 Yellow 55201 4 Green 4 Blue AUX Orange Brown Violet Black White LINE 4 AUX 4 AUX installation manual
4.3. Zone with Zone Controller (basic installation) Zone Controllers (ref. 557 22) can be install in areas or rooms where other type of Speakers are required different from those of i500 Series. The Zone Controller is connected to the communications line LINE through the connector module line (REF. 573 x1), using the cable supplied with the Zone Controller. The connector module line is available in different colors and can be integrated with the most popular brands of light switches in the market.
i500 Multiroom Audio System 4.4. Zone with Zone Controller (extended installation) Zone controllers (ref. 557 22) can be install in areas or rooms where other type of Speakers are necessary different from those of i500 Series and also when is required more power as external amplifiers and speakers can be connected. For this the Zone Controller has a Line output of 4 terminals where any external amplifier can be connected. For example, the diagram below shows how to connect EISSOUND amplifiers ref.
5. Installation configuration In the following process it is assumed that all the units are not installed and still under factory settings. To reset the system to factory default settings see section 6. 5.1. Configuring each Main Speaker and each Zone Controller with its own Remote Control Unit Supplying power to the system Engage the automatic switch that feeds the power to all system components.
i500 Multiroom Audio System The Remote Control Unit displays the initial screen, pending start up of the installation process. battery Start-up Screen not installed The Remote Control Unit can be operated while stationed in the base. It is recommended that the Remote NOT BE SEPARATED FROM THE BASE until the batteries are completely charged. As a general rule IT IS RECOMMENDED that when not in use the Remote Control Unit remain inserted in its Base.
bip bip bip Amaral Zone name: Escapar KITC H EN Estrella de mar Home address Estrella de mar edit At this point a name is assigned to the Main Speaker or Zone Controller which is emitting the BEEP signal. Use the navigation keys. The zone name is linked with the Main Speaker or Zone Controller and NOT with the Remote Control Unit.
i500 Multiroom Audio System When the first Remote Control together with the Main Speaker or Zone Controller has been linked the Central Unit LEDS stop flashing and the Sound sources are on and available at this step. L2 external sound source connected L1 external sound source connected Universal Dock for iPod connected Disk inserted FM tuner active This step must be repeated with all the Remote Control Units and Main Speaker or Zone Controllers sets installed in the different zones or rooms in the home.
5.2. Configuring several Main Speakers and Zone Controllers with the same Remote Control Unit The i500 multi-room system allows for a single Remote Control Unit to operate different Main Speakers or Zone Controllers. However, in order to make the best use of its features, it is HIGHLY RECOMMENDABLE that each zone or room have a Main Speaker and its own Remote Control Unit.
i500 Multiroom Audio System 5.3. Incorporate a new Remote Control Unit to the current system When all the Main Speakers and Zone Controllers are installed and a new Remote Control Unit will be added, proceed as follows: Open the installation Briefly push (under 2 seconds) the “reset” button. ! Short press: OPEN installation The Master Unit, the Main Speakers and the Zone Controllers LEDS emit FAST FLASHING to indicate that the installation is open to receive new Remote Control Units.
Close the installation Briefly push (under 2 seconds) the “reset” button. ! Short press: CLOSE installation All the LEDS (Master Unit, Main Speakers or Zone Controllers) stops flashing to indicate that the installation is CLOSED, meaning that it will not admit new Remote Control Units. Wait 30 seconds before the Remote Control Units and Main Speakers or Zone Controllers are operative.
i500 Multiroom Audio System Zone Name: change the actual name of the zone. My groups: define 8 groups of zones for intercom calls to several areas simultaneously, for example, “GROUP 1” can include the zones “KITCHEN”, “LIVING ROOM” and “GARAGE”. Permissions: block the access to certain operations such as limiting the use of intercom calls.
Keep the “reset” button pressed on the Master Unit for 10 seconds until all the frontal LEDS are illuminated. ! (10sg) factory setting Next, all the LEDS on the Master Unit, all the Main Speakers and all the Zone Controllers signal SLOW FLASHING to indicate they are NOT INSTALLED. For each of the Remote Control Units, at the start-up screen or audio channel screen, press the “on/off” , key “intercom calls” , and left navigation for 5 seconds.
i500 Multiroom Audio System 7.
Auxiliary Speaker 55201 MIN Measurements Voltage Consumption demand 85 NORMAL 220x93 190x85 220x8,5 230 18 MAX 12 5 5 mm mm mm Vac W mA Veff Kohms V W W 20000 0,1 dB Hz % 264 180 Input signal Input impedance Aux.
i500 Multiroom Audio System 8.
Recommendations to achieve enhanced communication between the Remote Control Unit and the Main Speaker or Zone Contoller Be within the range of coverage to a maximum distance of 5 m from the Main Speaker or Zone Controller 5m. OK NO Do not move while operating the Remote Control Unit. 5m.
i500 Multiroom Audio System Avoid nearby devices that emit Bluetooth, Wi-Fi or any other radiofrequency that transmits at 2.4 GHz. IMPORTANT: When the signal between the Remote Control and the Main Speaker or Zone Controller fails and contact is temporarily lost, the symbol in the top lefthand corner will disappear from the display screen. When this happens, the Remote Control will automatically try and reestablish the contact.
FAQ's: Frequently Asked Questions When installing one zone with the Remote Control the Main Speaker or Zone Controller stops blinking, but in the Remote Control does not appear the option of defining the name of zone press key "link" in the zone list select the “Find…” option as many times as necessary until you see the last zone called "Room X" (X=1,2,3,...
Polígono Malpica Calle F Oeste Grupo de Naves Gregorio Quejido, 87-88 50016 Zaragoza (España) Tel.: 34 976 465 550 Fax: 34 976 465 559 comercial@eissound.com www.eissound.
ESTE CAJETÍN NO FORMA PARTE DEL MANUAL 33