For Microsoft Windows CE 2.12 Version C LCD Monitor integrated Windows-based Terminal Touch Panel LCD Monitor integrated Windows-based Terminal Please confirm the version of the software built in eClient, and refer to the suited User's Manual (Refer to the User's Manual Version List on next page). This is the manual for the following software version. * Microsoft Windows CE: 2.12 Rev.3.53 or later * Microsoft Terminal Server Client: Ver.5.60 or later * ICA Client: Ver.6.
User’s Manual Version List A handling description changes with versions of the software built in eClient. refer to below. Please NOTE • The version of software built in eClient can be checked with a [System]-[ICA] tab of [Terminal Properties]. OS: Microsoft Windows CE 2.12 Software Microsoft Windows CE Microsoft Windows Terminal Server ICA Client Software C (This Manual) 2.12 Rev.3.53 or later Version 5.60 or later Version 6.30 [Build1078] or later B 2.12 Rev.3.51 or later Version 5.
English SAFETY SYMBOLS This manual uses the safety symbols below. They denote critical information. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety. Copyright© 2002-2003 EIZO NANAO CORPORATION All rights reserved.
English TABLE OF CONTENTS 1. INTRODUCTION ..................................................................................... 5 1-1. General Description ......................................................................................5 1-2. Features ........................................................................................................6 1-3. Package Contents..........................................................................................6 1-4. Controls & Connectors ........
English 1. INTRODUCTION Thank you very much for purchasing the EIZO eClient 530L/531L/531LT-GR. 1-1. General Description The eClient is a terminal which displays applications on a Windows Terminal Server (WTS) or a web site and conveys input by a keyboard or a mouse to the WTS. To operate the eClient, please connect it to a WTS with Microsoft Window NT Terminal Server Edition or Windows 2000 Server / Advanced Server / Datacenter Server.
English 1-2. Features • Lower TCO* *TCO (Total Cost of Ownership) Expense for managing and administrating computer systems. • Saves Space and Power Consumption • Less Heat, Less Noise • 531L/531LT-GR * Serial Port for Modem/PDA (*Hayes AT Compatible Modem Supported) * Portrait resolution supported [In use of the Citrix ICA Client (ICA)] • 531LT-GR * A Touch Panel and a Stylus Provided 1-3. Package Contents Please contact your local dealer for assistance if any of the listed items are missing or damaged.
English 1-4. Controls & Connectors Front (1) (2) (1) (2) Power Switch Power Indicator Power Indicator Unit Green Operation Screen saver mode Yellow Power save mode NOTE • When turning off/on the unit, leave the unit off for a few seconds before turning it on again. 1.
English Rear (10) (8) (9) (11) (3)(4) (5) (3) (4) (5) (6) (7) (8) (9) (10) (11) *1 *2 8 (6) (7) Mouse Connector Keyboard Connector Ethernet Connector (10 Base-T) Parallel Connector Power Connector Serial Connector (RS-232C) (531L/531LT-GR) Security Lock*1 Holes for Mounting an Arm Stand*2 Stand This allows for connection of a security cable. This lock supports Kensington's MicroSaver security system.
English 1-5. Overview Directions for the eClient’s Setup 2. CONNECTING THE p.10 3. SETTING UP THE eClient 3-1. WBT Setup Wizard p.13 3-2. Dial-Up Connection p.27 4. ADDING & CHANGING A CONNETION NAME 4-1. Adding a Connection Name p.34 4-2. Deleting a Connection p.52 4-3. Editing a Connection p.53 4-4. Setting an Autostart Connection p.55 Directions for the eClient’s Operation. 5. LOGON & LOGOFF 5-1. Logon to a WTS p.56 5-2. Logoff from the WTS p.
English 2. CONNECTING THE eClient This chapter shows how to connect the eClient to a WTS. 2-1. Setting up the eClient Please observe the following cautions when connecting the eClient. WARNING Place the eClient on a strong, stable surface. A unit placed on an inadequate surface may fall, resulting in injury or equipment damage. If the unit falls, disconnect the power immediately and have the unit checked by a qualified service engineer before using it again.
English 2-2. Connecting the eClient NOTE • Before connecting the eClient, confirm the following: • The eClient is turned off. • The WTS is turned on. • Connect the peripherals to the appropriate connectors of the unit. 1. In case of connecting the WTS through LAN: Connect the eClient to the network with an ethernet cable. In case of a dial-up or dial-in connection (531L/531LT-GR only): Connect the eClient to a modem or a modem card. Modem Card Printer Power Cord Network Keyboard Mouse 2.
English 3. Plug the power cord into the power connector. WARNING Use the enclosed power cord and connect to the standard power outlet of your country. Be sure to remain within the rated voltage of the power cord. Not doing so may cause in fire or electric shock. The equipment must be connected to a grounded main outlet. Not doing so may cause in fire or electric shock. 12 2.
English 3. SETTING UP THE eClient This chapter presents how to prepare for a connection with a WTS when the eClient starts up for the first time. 3-1. WBT Setup Wizard 1. Turn on the power switch. The power indicator turns green. NOTE • When no picture is displayed, or when the following message is shown on the screen, please refer to “8. Troubleshooting” on page 92.
English 2. “Touch panel calibration” is displayed (531LT-GR only). Five targets are displayed on the screen. Press the targets with a stylus or a fingertip to locate the center of the touch panel. If you accidentally touched the screen in the wrong spot during calibration, you will distort the touch panel calibration. 3. “Calibration measured” window is displayed when you finished (531LT-GR only). Click the “Enter” key to accept the settings. 14 3.
English 4. “WBT Setup Wizard” is displayed. Click [Next>]. 5. End User License Agreement page is displayed. Read the content and click [Accept] to continue. 3.
English 6. IP address setting page is displayed. [Yes, use the IP information supplied by DHCP.] ...................................Select this when using DHCP service. All the necessary information of the eClient including the IP address will be obtained by the DHCP. [No, I will enter static IP information.] ...................................Select this when not using DHCP service. Enter the IP address of the eClient. If DHCP service is not in operation, following message appears.
English 7. IP address page is displayed. [IP Address] ........................Type the IP address of the unit. [Subnet Mask] ....................Type the subnet mask of the network. [Gateway] ...........................Type IP address of the Gateway machine if necessary. Click [Next>] when finished. 3.
English 8. DNS and WINS settings page is displayed. This check box should be marked when DNS or WINS is used. NOTE • Skip the page by clicking [Next>] if DNS or WINS is not used. If using DNS Click the [Enable DNS] check box to activate this box. [Default Domain Name] .....Type the default domain name. [Primary Server IP]..............Type the DNS primary Server IP address. [Secondary Server IP] ..........Type the DNS secondary Server IP address.
English 9. Desktop area resolution and color settings page is displayed. Select the preferable display mode from the two available modes: · 1024 x 768 (256 colors) · 1024 x 768 (65,536 colors) · 768 x 1024 (256 colors) (531L/531LT-GR only) · 768 x1024 (65,536 colors) (531L/531LT-GR only) NOTE • The orientation of 768 x 1024 is a portrait. (768 x 1024 available for Citrix ICA. When RDP is used, 640 x 480 is displayed on center of the screen.
English 10. Local Printer Setup page is displayed. NOTE • The following is required to install a local printer; * A printer is connected to the printer port or the serial connector of the eClient. * An RDP protocol is used for connection to a WTS. * Microsoft Windows 2000 Server / Advanced Server / Datacenter Server is installed in a WTS • A Local Printer mentioned here is a printer connected directly to the Parallel Connector of the unit. Select [Yes] when using a local printer.
English 11. Printer port selection page is displayed. Select a printer port. The eClient supports LPT1. Click [Next>]. 3.
English 12. Printer model selection page is displayed. Select a manufacturer and model of your printer. [User Defined].....................Click the check box if your printer is not listed. Click [Next>] when finished. Refer to step 13 if clicking [User Defined]. Refer to step 14 if not clicking [User Defined]. 13. Printer model and manufacturer settings page is displayed. [Model Name] ....................Type a model and manufacturer of your printer. Click [Next>] when finished. 22 3.
English 14. Printer name setting page is displayed. Name the printer or use the indicated name. (Some programs do not support the Server and the printer name combinations of more than 31 characters.) Click [Next>] when finished. 3.
English 15. Default printer setting page is displayed. Select [Yes] to set this printer as the default printer. Select [No] not to set this printer as the default printer. Click [Next>]. 24 3.
English 16. Another printer configuration page is displayed. Select [Yes] to configure another printer. Select [No] to finish printer settings. Click [Next>] when finished. Refer to step 11 if selecting [Yes]. Refer to step 17 if selecting [No]. 3.
English 17. The last page of the “WBT Setup Wizard” is displayed. Click [Finish] in the last page to display a “Terminal Settings change” dialog box. (This dialog box is displayed only when there are changes in the settings.) Click [Yes] to restart the eClient to activate the changes. · Click [No] to finish the “WBT Setup Wizard” and display “Terminal Connection Manager” on the screen. The setting is not activated until the eClient is restarted. This completes the eClient settings.
English 3-2. Dial-Up Connection (531L/531LT-GR only) The following details the installation of a dial-up connection for RAS (Remote Access Service). No restriction of the protocol is made for the “Dial-up connection”. To use a dial-up connection requires an RAS server in operation. [Dial-up Connection] Telephone Lines RAS Server eClient WTS WTS FTP Server NOTE • Another type of connection using a modem, a dial-in connection, is available to connect to the WTS with an ICA protocol. Please see page 40.
English 2. “Terminal Properties” is displayed. Click the [Network] tab. 3. The network setting window is displayed. Select [Use PPP connection or another network adapter]. Click [PPP] tab when finished. 28 3.
English 4. The dial-up setting window is displayed. NOTE • Enter your information in the pertinent fields. [Connection Name] ............Choose a connection name for a dial-up connection. ([None] indicates no connection name chosen.) [New...]...............................Click the button to create a new dial-up connection name. “Create New Dial-Up Connection” dialog box is displayed. Enter the name and click [OK]. [Remove] ............................Delete the connection name displayed currently.
English [Dialing Properties...] ...................................Click the button to set information of the sender. [When dialing from:] ..........Choose the sender’s location. [New...]...............................Click this to add a new sender’s location. “Create New Location” dialog box is displayed. Enter a new sender’s location and click [OK]. [Remove] ............................Remove the current sender’s location. [Local Settings are...] [The local area code is:], [The local country code is:] ..
English [Device Configure...] ...................................Click the button the detailed settings of the modem. (Please refer to the instruction manual of a modem for settings of the modem.) [Port Settings] tab [Manual Dial (user supplies dial strings)] ...................................Click this box to set up for manual dialing. [Terminals] [Use terminal window before / after Dialing] ...................................Click this box to record terminal window information before or after dialing.
English [TCP/IP Settings...] Click the button to set the TCP/IP settings of the WTS. [Use server-assigned IP address] ...................................Click the box to use a server-assigned IP address. [Specify an IP address] ........Enter a provided IP address. [Use server-assigned DNS or WINS server IP address] ...................................Click the box to use a server-assigned DNS or WINS server IP address. [Specify DNS or WINS server IP address] ...................................
English [Primary DNS], [Secondary DNS] ...................................Enter IP address of the primary DNS and IP address of the secondary DNS. [Primary WINS], [Secondary WINS] ...................................Enter IP address of the primary WINS and IP address of the secondary WINS. [Use software compression] ...................................Click to use software compression. [Use IP header compression] ...................................Click to IP header compression. [Use default gateway].........
English 4. ADDING & CHANGING A CONNETION NAME This chapter shows how to add, delete, and modify connection names to a WTS. All the settings are managed in the “Terminal Connection Manager”. 4-1. Adding a Connection Name These are settings for the Server connection. Each protocol has different settings. Please install the appropriate settings.
English In Use of RDP Protocol 1. Display [Terminal Connection Manager]. Click the [Configure] tab and [Add...] to set the connection information of the WTS. 2. Protocol selection dialog box is displayed. Select the “Microsoft Remote Desktop Client” (RDP) Click [OK] when finished. 4.
English 3. “WTS Connection Wizard” is displayed. [Name]................................Type the connection name to the Server. Name the connection to differentiate the Server from others. [Server] ...............................Type the IP address or the name of the Server, or WINS setting is necessary when the name is typed. [Low Speed Connection].....Click the check box when making a low speed connection.
English 4. Automatic Logon setting page is displayed. Type the name, the password, and the domain name of the WTS beforehand to enable an Automatic Logon to the WTS after connecting. NOTE • If an Automatic Logon is not needed, click [Next>]. Click the check box of the [Automatic Logon] to enable the item. [Username]..........................Type the name to connect the WTS. [Password] ..........................Type the password for the user name. [Domain] ............................Type the domain name.
English 5. Specifying an application to run after connecting to a WTS is displayed. Select whether to display the Windows desktop screen or start up an application. [Desktop] ............................Select this to start the Windows desktop screen when you connect. [Application file name:] .....Select this to start an application when you connect. [Working directory:] ...........Input the name of the application and the working directory if necessary.
English 6. The last page of the “WTS Connection Wizard” is displayed on the screen. Click [Finish] to return to the “Terminal Connection Manager” dialog box. The registered connection name is displayed in the “Terminal Connection Manager” dialog box. This completes the setup of the eClient for connection to a WTS with the RDP protocol. NOTE • Please repeat step 1 to 6 to entry more than two kinds of connections. 4.
English In Use of the ICA protocol 1. Click the [Configure] tab. Click [Add...]. 2. “New Connection” dialog box is displayed on the screen. Select “Citrix ICA Client” (ICA). Click [OK] when finished. 40 4.
English 3. “Specify Connection Type” dialog box is displayed. [Network Connection]........Select for network connection. [Dial-In Connection]...........Select for dial-in connection. Click [Next>] when finished. Go to step 4 when selecting [Network Connection]. Go to step 5 when selecting [Dial-In Connection]. 4.
English 4. Citrix Server or published application selection page is displayed. 1) Select [Server] (WTS) or [Published Application]. 2) Click [Server Location…]. [Server Group]................Select the WTS Group to connect. (A WTS Group consists of [Primary], [Backup 1], and [Backup 2]. The WTS will be searched in order of [Primary], [Backup 1], and [Backup 2]. [Add] ...............................Add another Server address. Type the Server Name or IP address.
English 3) Click [Refresh] to refresh the list to the newest information. 4) Select a WTS or a published application from the list. NOTE • Published applications are specific application set by a system administrator. When connected, you are presented with the application itself. Click [Next>]. 4.
English 5. “Dial-In Devices” dialog box is displayed. NOTE • This setting is available in the 531L/531LT-GR only. • A dial-in connection is not available during a dial-up connection. Disconnect the dial-up connection before making dial-in connection. [Dial-In Device:]..................Select the device name connected to the modem. [Hayes Compatible on COM1] is available for the eClient. [Phone Number] .................Enter a country code, an area code, and a phone number for the connection.
English [Connection Preference] [Baud Rate].........................Set the data transmission rate from 110 to 115,200. [Data Bits]...........................Set the data bits. [Parity]................................Set to check the data’s appropriate transmission. [Stop Bits] ...........................Set the length of the Stop Bits. [Flow Control]....................Set Flow Control. [Call Option] tab [Cancel the call if not connected within] ...................................
English 6. A title for the ICA connection page is displayed. Type a connection name of the WTS. Click [Next]. 7. An application selection page is displayed. Specify the command line and the working directory of an application to operate. NOTE • Leave these fields blank and click [Next>] to run a Windows desktop. [Command Line:]................Type the application name and the path. [Working Directory:] ..........Type the working directory for the application.
English 8. Automatic logon settings page is displayed. Type the name, the password, and the domain name of the WTS beforehand to enable an Automatic logon to the WTS after connecting. NOTE • If an Automatic Logon is not needed, click [Next.] [User Name:].......................Type the name to automatically connect the WTS. [Password:] .........................Type the password for the user name. [Domain:] ...........................Type the domain name. [Allow Smart Card logon]...
English 9. Colors selection page is displayed. Set the colors of the WTS’ screen. NOTE • Thousands can be selected only when the color setting of the eClient is 65536 colors. Click [Next>] when finished. 48 4.
English 10. Compression and encryption, and sound settings page is displayed. [Use Printer Configuration Utility] ...................................Click the check box to install the printer at the [ICA Client Printer Configurations]. [Compress Data Stream] .....Click the check box to reduce the amount of data transferred between the WTS and the eClient, which can increase performance. (If you have sufficient bandwidth, leave compression off to conserve processing power on the WTS.) [SpeedScreen:] .....
English 11. Firewall settings page is displayed. NOTE • These settings are effective when connecting to the WTS through internet. • If no change is made, the settings under the [Firewall settings] of [Global ICA Client Settings] will be applied (see page 78 for details). Set the connection to the WTS through the SOCKS proxy server when the SOCKS proxy server is working to limit the access to the WTS. [Proxy] Click the drop-down list box, and select [SOCKS] from the list.
English This completes the setup of the eClient for connection to a Server with the ICA protocol. NOTE • Please repeat the step 1 to 11 when you adding another connection name. 4.
English 4-2. Deleting a Connection This function deletes an existing Connection Name. 1. Display the “Terminal Connection Manager” dialog box. 2. Click the [Configure] Tab. 3. Select the Connection Name you want to delete. 4. Click [Delete]. 5. “Confirm Connection Delete” dialog box is displayed. Click [Yes] to delete the information of the selected WTS. 52 4.
English 4-3. Editing a Connection This function modifies attributes of the WTS connections. 1. Display the “Terminal Connection Manager” dialog box. 2. Click the [Configure] Tab. 3. Select the connection you want to modify. 4. Click [Edit...]. 5. [Edit Connection] dialog box or [Edit Connection Details] is displayed. • For RDP Connection (Please see pages 35 to 39 for each setting.) [Net Connections] tab........Change connection settings to a WTS. [Application] tab................
English • For ICA Connection (Please see to pages 40 to 50 for each setting.) [Server/Dial-In] tab .............Either Server or Dial-In tab is displayed depending on the connection type. [Server] Tab (for LAN connection) To change the WTS / the public application to use [Dial-In] Tab (for Dial-In connection) To change settings of the Dial-In connection (531L/531LT-GR only) [Application] tab.................To change a description of an application to run [Logon] tab .........................
English 4-4. Setting an Autostart Connection This function configures a connection to start automatically each time the eClient is turned on. (This function is available for a LAN connection.) 1. Display the “Terminal Connection Manager” dialog box. 2. Click the [Configure] tab. 3. Select the desired Connection Name for Autostart Connection. 4. Click [Startup...] 5. “Connection Startup” dialog box is displayed. Select [Automatically start the selected connection at startup.
English 5. LOGON & LOGOFF This chapter shows how to log on to and log off from a WTS. 5-1. Logon to a WTS 1. Turn on the eClient. 2. “Terminal Connection Manager” dialog box is displayed. Please follow the instruction depending on the network environment of the eClient. LAN connection Go to step 3. Modem connection (531L/531LT-GR only) * Dial-Up connection to the RAS Server Click the active button of a small window on the right bottom of the screen.
English 3. Click the [Connections] tab. Select the desired [Connection Name] and click [Connect] (or simply double click the connection name). NOTE • To connect to the default connection WTS set in the “Terminal Connection Manager” dialog box, press [Ctrl] + [Alt] + [Home] keys. (See page 55 on a default connection server setting.) 4. The eClient connects to the WTS, and the “Log On to Windows” dialog box is displayed. Type your [User name] and [Password], and click [OK] to log on to the WTS.
English Multi Session You can log on to the WTS with the several connection names, and switch the active sessions. • Logon 1. Log on with a Connection Name, as following the previous steps. 2. Press [Ctrl] + [Alt] + [End] keys after logon. 3. “Terminal Connection Manager” is displayed. Select another Connection Name to log on to, and click [Connect]. (Or double click the connection name.) 4. “Log On to Windows” dialog box is displayed after connecting to the WTS.
English 5-2. Logoff from the WTS If your eClient starts its operation with a desktop 1. Log off from the WTS. (1) Close all applications. (2) Select [Start] on the taskbar. (3) Microsoft Windows NT Server 4.0 Terminal Server Edition: Select [Logoff]. Microsoft Windows 2000 Server / Advanced Server / Datacenter Server: Select [Shut Down...] and select [Logoff] of the [Shut Down Windows] dialog box. (4) Click [OK] on the Logoff Window. The session ends and automatically logs off from the WTS.
English If your eClient starts its operation with an application 1. Log off from the WTS. Close applications to log off from the WTS. “Terminal Connection Manager” is displayed. If a dial-up connection is running, click the active button of the window on the right bottom of the screen. Clicking the button Disconnects the dial-up connection. (531L/531LT-GR only) 2. Shut down the eClient. NOTE • It is possible to Disconnect from a WTS without closing applications in use (or without logging off).
English 6. USING THE TERMINAL PROPERTIES This chapter presents how to modify all settings of the eClient using the “Terminal Properties”. To display the “Terminal Properties” during logging on, press F2 in the “Terminal Connection Manager” dialog box. (Press Ctrl + Alt + End to display the “Terminal Connection Manager”.) 6-1. General Information & Reset to Default Click [General] tab to confirm general settings and to reset the eClient to factory-default settings. Product Information [Product Name] .....
English Resetting to Default 1. Click [Reset the terminal to factory-default property settings] check box. 2. The “System Settings Change” dialog box is displayed. Click [Yes]. 3. “Terminal Properties” is displayed. Click [OK]. “Terminal Setting Change” dialog box is displayed. Click [Yes] to restart the terminal. “WBT Setup Wizard” will be displayed after restarting the terminal. 62 6.
English 6-2. Input Devices Settings Click the [Input] tab to modify keyboard, NumLock Key, mouse characteristics, and touch panel calibration. (530L/531L) (531LT-GR) Keyboard Settings [Keyboard] [Locale]...............................Selects a keyboard language. [NumLock Enable on Boot UP] ...................................enables/cancel NumLock function on start-up. [Character Repeat] [Repeat delay] ....................
English Mouse Settings Click [Properties...] to display the [Mouse Properties]. [Button Configuration] .......Assigns the primary mouse button and the secondary mouse button. [Speed] ................................Adjusts the speed at which the pointer moves on your screen. [Acceleration]......................Adjusts the speed the mouse pointer accelerates as you move the mouse. 64 6.
English Touch Panel Properties (531LT-GR only) Click [Properties...] to display the “Touch panel Properties”. [Mouse Right Click Emulation] [Enable right click emulation] ...................................Holding stylus for a fixed period of time emulates mouse right button click. Click the [Enable right click emulation] check box , set a holding time, and adjust holding sensitivity. 6.
English [Calibration] This enables to recalibrate the touch panel. Click [Recalibrate] to show the “Touch Panel calibration”. Five targets are displayed on the touch panel. Press the targets with a stylus or a fingertip to locate the center of the touch panel. If you accidentally touched the screen in the wrong spot during calibration, you will distort the touch panel calibration. “Calibration measured” window is displayed when you finished. 66 6.
English Click [Enter] key to accept the settings. Click [OK] to return to the “Terminal Properties” and save the settings. Click [OK] to close “Terminal Properties” and save the adjustments. The “Terminal Settings change” dialog box will be displayed when the [Locale:], [Repeat delay:], and [Repeat rate:] are changed. Click [Yes] and restart the eClient.
English 6-3. Colors & Power Save Settings Click the [Display] tab to modify display parameters such as colors, screen saver, and power save. Resolution and Colors [Desktop Area and Colors] [Details] ..............................Adjusts the resolution and colors of the screen. Screen Saver [Screen Saver] [Enable Screen Saver] ..........Click the [Enable Screen Saver] check box and set an idle period from 1 to 60 minutes before Screen Saver starts in minutes.
English Brightness [Contrast/Brightness] [Settings] .............................Enables to adjust the brightness of the screen. [Enable Contrast/Brightness control from Keyboard] Enables to adjust the brightness/contrast from a Keyboard. • [Alt] key and [+] key: The brightness of the screen increases. • [Alt] key and [-] key: The brightness of the screen decreases. Click [OK] to close “Terminal Properties” and save the adjustments.
English 6-4. Network Settings Click [Network] tab to set network information for the eClient. NOTE • All settings shown here are previously adjusted on the “WBT Setup Wizard”. • Please set the properties depending on the eClient connection settings. [Use PPP connection or another network adapter] ...................................Click to use a modem connection to the WTS. (531L/531LT-GR only) To connect to the WTS with a LAN network, set the following. [Obtain an IP address from a DHCP server] .........
English [DHCP Options...]..............Click this to receive essential information about the eClient from the DHCP server every time the eClient is turned on. Refer to “Practical Setup” on page 87 for details. [Advanced Network...] .......Allows setting for DNS/WINS service. A DNS/WINS server is required for the setting. [Enable DNS]......................Click the check box and type default domain name and IP address of the DNS server. [Enable WINS] ...................
English NOTE • The [Terminal Settings Change] dialog box will not be displayed when [Terminal Name], [DHCP Options], and [Advanced Network…] are changed, though the unit needs to be restarted to set the adjustment effective. 72 6.
English 6-5. Printer Settings Click [Printers] tab. You can add, delete and change the settings of the printer in this section. NOTE • The eClient supports a LPT1 port. • Use a RDP protocol to set the printer's adjustment. If you are using the ICA protocol, please refer to the instruction manual of the Citrix MetaFrame. 6.
English Adding another printer settings This enables to add a printer when no printer is connected to the LPT1 port. 1. Select LPT1 and click [Add]. 2. “Printer Properties” dialog box is displayed. [Friendly Name]..................Name the printer or use the indicated name. (Some programs do not support server and printer name combinations of more than 31 characters.) • When your printer is listed [Manufactures] / [Printers] ...................................
English Modifying the settings This enables to delete printer settings when a printer is connected to the LPT1 port. 1. Select LPT1 and click [Properties...]. 2. “Printer Properties” dialog box is displayed. Change the settings as needed. [Friendly Name]..................Changes the printer's name. (If you are naming the printer, the name combination must be 31 character or less.) • When your printer is listed [Manufactures] / [Printers] ...................................
English 6-6. Dial-Up (PPP) Connection Settings (531L/531LT-GR only) Click [PPP] tab to adjust the dial-up settings of eClient. The following details the installation of a dial-up connection to a WTS or a Web Server. (To use a dial-up connection requires an RAS server in operation.) Please see page 27 for each setting. 76 6.
English 6-7. ICA Settings Click [ICA] tab to confirm information about Citrix ICA Client version and to change the settings when connecting to the Citrix Server with ICA protocol. NOTE • The ICA settings are effective only when the unit is connected to the WTS with ICA protocol. Also, the settings will affect all the settings with ICA protocol. Confirming Citrix ICA Client information [Client Software].................Version of the Citrix ICA Client. 6.
English General Settings of the ICA Connection You can change the settings for the ICA Connection. 1. Click [Settings...]. 2. “Global ICA Client Settings” dialog box is displayed. [Hotkeys] tab ......................Enables to change the hotkeys when logging on to the Server. There are the hotkeys to control the eClient and the ones same as standard Windows hotkeys. Please refer to the instruction manual of the Citrix MetaFrame for details.
English [Firewall Settings] tab .........Change the settings of Firewall and SOCKS proxy server (see page 50). This setting change is displayed when adding a new connection. NOTE • If connecting a WTS through internet, the settings should be completed before the WTS is selected. • If you configure a default SOCKS proxy server, you must specify at least one WTS in the [Server Location] tab for a WTS and published application browsing to work.
English 6-8. Product Information, Security & Updating Software Click [System] tab to confirm information about the eClient, to set the security, and to update firmware. Product Information [Software] [Microsoft Windows CE] ...................................Microsoft Windows CE Version, Revision [Windows Terminal Server Client] ...................................Window Terminal Server Client Revision [Boot software] ...................Boot Software Version of the eClient [Update...].......................
English Security Settings This enables settings on network information of the WTS invisible to prevent from undesirable change. When the security is active, the following settings become. • “Terminal Connection Manager” * [Configure] tab • “Terminal Properties” * [General] tab... [Reset the terminal to factory - default settings] * [Network] tab * [Printers] tab * [PPP] tab * [ICA] tab * [System] tab... [Update...], [Security] PROCEDURE 1. Click the [Security Enable] box. 2. Click [Setting Password...
English CANCELING SETTINGS 1. Display “Terminal Connection Manager”. 2. Press [Ctrl], [A], and [F2] at the same time. 3. “Enter Security Password” dialog box is displayed. [Password:] .........................Enter the password Click [OK] on [Enter Security Password] when finished. 4. All settings in the “Terminal Properties” will be active. Click the [Security Enable] check box on the [System] tab and remove the check mark.
English Software Updating You can update the built-in software. NOTE • Before updating, please complete the following: * Copy the update file (*.bin) to the accessible file folder of the FTP Server. * If the WTS is connected with LAN, close all the connections to the FTP Server. * Make a dial-up connection if it is adopted to connect the WTS. Software Updating is not available if a dial-in is adopted to connect the WTS. 1. Click the [Update...] of [Software]. The following message appears.
English 2. The “Software Update” dialog box appears. [Server:] .............................Type IP address or full domain name of the FTP Server. [User Name:].......................Type the user name to connect the FTP Server. [Password:] .........................Type the password for the user name to connect the FTP Server. [File Name:] ........................Type the folder and copied file name located in the FTP Server.
English NOTE • Clicking the "Execute automatic software update." check box will automatically consult the update file in the location indicated in the "Software Update" dialog box each time turning on the unit. If the update file consulted is newer, the software will be updated automatically while displaying the following dialog box. When updating the software, please set the following; (This function is not available for a modem connection. Please do not click the check box.
English NOTE • Failing to download results in program's returning to the "Software Update" dialog box. * In case of returning to the "Software Update" dialog box, confirm such as network settings and redo the [Settings] before clicking [Download]. * In case of retry dialog box is displayed, confirm connection or network settings by following the message, and click [Retry]. If the setting still fails, click [Cancel] to automatically restore the original software and restart the unit.
English 7. PRACTICAL SETUP By utilizing the DHCP Option function of the DHCP Server, necessary information is supplied by the DHCP Server, and each setting is automatically set every time the unit is turned on. The following information can be obtained by the eClient.
English DHCP Server Settings Please open DHCP settings to configure each DHCP Option as follows. [Key] ...................................Set the value as “EIZO”. (The eClient will not accept any value but “EIZO”.) [Server] ...............................Type an IP address of the Server installing an update file and a registry file of the eClient. [User Name]........................Type the user name to logon to the FTP Server. [Password] ..........................Type the password for the user name.
English NOTE • Making a Registry File to Connect to a WTS/Web Server. Please refer to the example below, make a registry file, and save it in Unicode format. Please change the italic bold phrases as necessary. - ConnectionName : Type the connection name in the “Terminal Connection Manager”. - TerminalServerAddress : Type the IP address or the full domain name of the WTS. - URL : Type the URL of the Web Server. (Including “http://”.) Registry file ...........................................................
English "StartCmdLineArgs"="/L "ConnectionName"" ......... Command argument to connect to a WTS "StartExe"="WFICACE" ............................. Fixed – Command (executable file) to connect to a WTS "ScreenPercent"="100" ............................ Fixed – Assign the ratio of the eClient screen to the displayed Window of the WTS. Name displayed on the Connection Manager "Description"="ConnectionName" ................... "Address"="TerminalServerAddress" ................
English eClient Settings The eClient’s default setting is to enable DHCP Options. There is no need for extra settings. After initial setup, confirm the following: • [Use PPP connection or another network adapter]in the [Network] tab of “Terminal Properties” is selected. • Press “DHCP Option” on “Network” tab in the “Terminal Properties”. “DHCP Options” is displayed. [Enable DHCP Option] is selected, and code numbers assigned for the DHCP options.
English 8. TROUBLESHOOTING This page presents problem that can be corrected by the user. If a problem persists even after applying the suggested remedies, contact an EIZO dealer. Problems Points to check with possible solutions 1. No picture is displayed on the screen. Check if the power is OFF. Check brightness setting. Minimum settings will cause screen to be blank. Try pressing a key on the keyboard, or clicking the mouse. (The monitor may be in a power saving mode.) 2.
English Problems Points to check with possible solutions 4. Afterimages appear on the screen. When the screen image has been changed after displaying the same image for a long period, afterimages may appear. Use the screen saver and avoid leaving the screen on all the time. 5. The screen has defective pixels (e.g. slightly light or dark). This is due to the characteristics of the panel itself, and not the failure. 6. Finger prints appear on the screen.
English 9. CLEANING Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime. NOTE • Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl alcohol), abrasive cleaners, or other strong solvents, as these may cause damage to the cabinet or LCD panel. Cabinet To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild detergent. Do not spray wax or cleaner directly onto the cabinet.
English Mouse If you find that the pointer on the screen doesn’t move smoothly, your mouse needs to be cleaned. Periodically clean the mouse for your operation. (1) Turn off the eClient. (2) Turn the mouse upside down and remove the mouse trackball cover. Press the cover towards “Open” while pulling the other side of the cover. Press (3) Remove the trackball. (4) Wipe the trackball with a soft cloth with neutral detergent. (5) Clean all the rollers, getting all the lint off of them.
English 10. SPECIFICATIONS 530L CPU and Memory CPU Memory LAN NEC VR4121-168, 168 MHz RAM; 32 MB, ROM;16 MB 10BASE-T Display LCD Panel 38 cm (15 inch) TFT color LCD panel Anti-Glare Hard Coating (Viewing Angle: Horizontal; 120°, Vertical; 140°) Dot Pitch 0.297 mm x 0.297 mm Resolution 1024 x 768 Viewable Image Size 304.1 mm (H) x 228.1 mm (V) (11.9" (H) x 8.
English 531L CPU and Memory CPU Memory LAN NEC VR4121-168, 168 MHz RAM; 32 MB, ROM;16 MB 10BASE-T Display LCD Panel 38 cm (15 inch) TFT color LCD panel Anti-Glare Hard Coating (Viewing Angle: Horizontal; 120°, Vertical; 140°) Dot Pitch 0.297 mm x 0.297 mm Resolution 1024 x 768 (768 x 1024) Viewable Image Size 304.1 mm (H) x 228.1 mm (V) (11.9" (H) x 8.
English 531LT-GR CPU and Memory CPU Memory LAN NEC VR4121-168, 168 MHz RAM; 32 MB, ROM;16 MB 10BASE-T Display LCD Panel 38 cm (15 inch) TFT color LCD panel Anti-Glare Hard Coating (Viewing Angle: Horizontal; 120°, Vertical; 140°) Dot Pitch 0.297 mm x 0.297 mm Resolution 1024 x 768 (768 x 1024) Viewable Image Size 304.1 mm (H) x 228.1 mm (V) (11.9" (H) x 8.
English Dimensions mm (inches) 530L 531L 531LT-GR 10.
English 11. REFERENCE 11-1. Attaching an Arm Stand The eClient can be used with an arm stand by removing the tilt stand and attaching the arm stand to the terminal. NOTE • Use an arm stand that satisfies the following. - When using the eClient with an arm stand, the arm stand must be VESA approved : Use an arm stand with a 75 mm x 75 mm hole spacing on the arm mounting pad. Use an arm stand that is able to support an object weighing 8.0 kg. A GS approved arm stand.
English 3. Attach an arm stand to the eClient securely. WARNING Install the unit securely when attaching to an arm stand. When attaching an arm stand, please refer to the user’s manual of the arm stand and install the unit securely with the enclosed screws. Not doing so may cause the unit to come unattached, which may result in injury or equipment damage. When the unit is dropped, please ask your dealer for advice. Do not continue using a damaged unit.
English INDEX A I ADDING & CHANGING A CONNETION NAME ...............................................34 Administration Console ............................82 Application to Run..............................38, 46 Attaching an Arm Stand.........................100 Automatic Logon ................................37, 47 Autostart Connection ...............................55 ICA ....................................................34, 40 ICA Connection........................................54 ICA Settings ..
English S Screen Saver ...........................................68 Security Settings......................................81 Serial Port ..................................................6 Server Location........................................78 Setting up.................................................10 Software Updating ...................................83 Specifications...........................................96 Specify an IP Address .............................17 Specify Connection Type ......
