- For System Integrators Version. E IMPORTANT Please read this User’s Manual carefully to familiarize yourself with safe effective usage procedures. Please retain this manual for future reference. CAUTION Please carefully read the ‘PREACAUTION’ section in the user’s manual enclosed with the unit before using the unit. This product has been adjusted specifically for use in the region to which it was originally shipped.
SAFETY SYMBOLS This manual uses the safety symbols below. They denote critical information. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety. Copyright© 2002 by EIZO NANAO CORPORATION. All rights reserved.
TABLE OF CONTENTS 1. INTRODUCTION ..................................................................................... 5 1-1. General Description ......................................................................................5 1-2. Features ........................................................................................................6 1-3. Package Contents..........................................................................................6 1-4. Controls & Connectors .................
INDEX .....................................................................................................
English 1. INTRODUCTION Thank you very much for purchasing the EIZO eClient 630L. 1-1. General Description The 630L is a terminal which displays applications on a Windows Terminal Server (WTS) or a web site and conveys input by a keyboard or a mouse to the WTS. To operate the 630L, please connect it to a WTS with Microsoft Window NT Terminal Server Edition or Windows 2000 Server / Advanced Server / Datacenter Server.
English 1-2. Features • Lower TCO* • TCO (Total Cost of Ownership) Expense for managing and administrating computer systems.
English 1-4. Controls & Connectors Front (4) (3) (2) (1) (1) (2) (3) (4) Power Switch Power Indicator Green Operation Screen saver mode Yellow Power save mode Off Power off (Wake on LAN standby ) NOTE • When turning off/on the unit, leave the unit off for a few seconds before turning it on again. Volume Speakers 1.
English Rear (16) (17) (14) (15) (13) (6) (8) (10) (12) (5) (7) (9) (11) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) *1 *2 8 Mouse Connector Keyboard Connector Serial Port (RS-232C) Parallel Connector Power Connector Ethernet Connector (10 Base-T, 100 Base-T) Headphone Connector Microphone Connector USB Port (Downstream) x 2 PC Card Slot Security Lock*1 Holes for Mounting an Arm Stand*2 Stand This allows for connection of a security cable.
English 1-5. Overview Please refer these during 630L setup. 2. CONNECTING THE 630L p.10 3. SETTING UP THE 630L 3-1. WBT Setup Wizard p.13 3-2. Connection p.29 3-3. Dial-Up Connection p.36 4. ADDING & CHANGING A CONNETION NAME 4-1. Adding a Connection Name p.43 4-2. Deleting a Connection p.60 4-3. Editing a Connection p.61 4-4. Setting an Autostart Connection p.64 Please refer these during the 630L operation. 5. LOGON & LOGOFF 5-1. Logon to a WTS / Logoff from a WTS p.65 5-2.
English 2. CONNECTING THE 630L This chapter explains how to connect the 630L to a WTS. 2-1. Setting up the 630L Please observe the following cautions when connecting the 630L. WARNING Place the 630L on a strong, stable surface. A unit placed on an inadequate surface may fall, resulting in injury or equipment damage. If the unit falls, disconnect the power immediately and have the unit checked by a qualified service engineer before using it again.
English 2-2. Connecting the 630L NOTE • Before connecting the 630L, confirm the following: • The 630L is turned off. • The WTS is turned on. • Connect the peripherals to the appropriate connectors of the unit. 1. In case of connecting the WTS through LAN: Connect the 630L to the network with an ethernet cable. In case of a dial-up or dial-in connection: Connect the 630L to a modem or a modem card.
English 3. Plug the power cord into the power connector. WARNING Use the enclosed power cord and connect to the standard power outlet of your country. Be sure to remain within the rated voltage of the power cord. Not doing so may cause in fire or electric shock. The equipment must be connected to a grounded main outlet. Not doing so may cause in fire or electric shock. 12 2.
English 3. SETTING UP THE 630L This chapter presents how to prepare for a connection with a WTS when the 630L starts up for the first time. 3-1. WBT Setup Wizard 4. Turn on the 630L. The power indicator turns green. NOTE • When no picture is displayed, or when the following message is shown on the screen, please refer to “8. Troubleshooting” on page 106. - Message - 5. “WBT Setup Wizard” is displayed. Click [Next>]. 3.
English 6. End User License Agreement page is displayed. Read the content and click [Accept] to continue. 14 3.
English 7. IP address setting page is displayed. [Yes, use the IP information supplied by DHCP.] ...................................Select this when using DHCP service. All the necessary information of the 630L including the IP address will be obtained by the DHCP. [No, I will enter static IP information.] ...................................Select this when not using DHCP service. Enter the IP address of the 630L. If DHCP service is not in operation, following message appears.
English 8. IP address page is displayed. [IP Address] ........................Type the IP address of the unit. [Subnet Mask].....................Type the subnet mask of the network. [Gateway] ...........................Type IP address of the Gateway machine if necessary. Click [Next>] when finished. 16 3.
English 9. DNS and WINS setting page is displayed. This check box should be marked when DNS or WINS is used. NOTE • Skip the page by clicking [Next>] if DNS or WINS is not used. If using DNS Click the [Enable DNS] check box to activate this box. [Default Domain Name] .....Type the default domain name. [Primary Server IP]..............Type the DNS primary Server IP address. [Secondary Server IP] ..........Type the DNS secondary Server IP address.
English 10. Desktop area resolution and color settings page is displayed. Select the preferable display mode from the two available modes: · 1024 x 768 (256 colors) · 1024 x 768 (65,536 colors) Click [Next>] when finished. 18 3.
English 11. Browser Setup page is displayed. Select [Yes] if you are setting up a web browser connection. Click [Next>] when finished. Refer to step 9 if selecting [Yes]. Refer to step 13 if selecting [No]. 3.
English 12. Browser URLs page is displayed. [Home Page:] ......................Type the URL for the page to be displayed when Internet Explorer starts up or the “Home” button is clicked. [Search Page:]......................Type the URL for the page to be displayed when the “Search” button is clicked. Click [Next>] when finished. 20 3.
English 13. Preferences page is displayed. [When do you want the browser to underline hyperlinks?] ...................................Select when you want the hyperlinks to be underlined. [What size font do you want to use?] ...................................Select the font size of the web page. Click [Next>] when finished. 3.
English 14. History and Favorites page is displayed. [Persistent browser cache]...Click the check box if you want the “History” and “Cookies” portions of the browser cache to persist across Web sessions. [Enable Favorites] ...............Click the check box if you want to enable the “Favorites” feature. (Favorites will persist across Web sessions.) Click [Next>] when finished. 22 3.
English 15. Proxy server selection page is displayed. [Use proxy server]...............Click the check box if you use proxy server for the web browser connection. [Type the name of the computer running the proxy server:] ...................................Type the name of the computer running the proxy server. [Port] ..................................Type the port number. [Bypass proxy server for local (Intranet) addresses.] ...................................
English 16. Local Printer Setup page is displayed. NOTE • The following must be satisfied to install a local printer; * When a printer is connected to the printer port or the serial connector of the 630L. * The RDP protocol for connection to a WTS. * Microsoft Windows 2000 Server / Advanced Server / Datacenter Server as the OS for the WTS • A Local Printer mentioned here is a printer connected directly to the Parallel Connector of the unit. Select [Yes] when using a local printer.
English 17. Printer port selection page is displayed. Select the printer port. The 630L supports only LPT1 and COM1. Click [Next>]. 18. Printer model selection page is displayed. Select a manufacturer and a model of your printer. Click [Next>] when finished. 3.
English 19. Printer name setting page is displayed. Name the printer or use the indicated name. (Some programs do not support the Server and the printer name combinations of more than 31 characters.) Click [Next>] when finished. 20. Default printer setting page is displayed. Select [Yes] to set this printer as the default printer. Select [No] not to set this printer as the default printer. Click [Next>]. 26 3.
English 21. Another printer configuration page is displayed. Select [Yes] to configure another printer. Select [No] to finish printer settings. Click [Next>] when finished. Refer to step 14 if selecting [Yes]. Refer to step 19 if selecting [No]. 22. The last page of the “WBT Setup Wizard” is displayed. 3.
English Click [Finish] in the last page to display a “Terminal Settings change” dialog box. (This dialog box is displayed only when there are changes in the settings.) Click [Yes] to restart the 630L to activate the changes. · Click [No] to finish the “WBT Setup Wizard” and display “Terminal Connection Manager” on the screen. The setting is not activated until the 630L is restarted. This completes the 630L settings. The “Terminal Connection Manager” dialog box will be displayed after restarting.
English 3-2. Connection with a LAN card The following details the installation of a LANs connection. NOTE • Please remove the lid on the side of the 630L before connecting a LAN card, and then insert a LAN card to the card slot. • For use of an ethernet cable, a LAN card, or a LUCENT ORINOCO Waveland wireless LAN card: See page 29. • For use of a CISCO Aironet wireless LAN card: See page 33. Connection with a LAN card other than Aironet LAN Card 1. Press “F2” key in the “Terminal Connection Manager”.
English 3. The “Network” page is displayed. Select [Use PPP connection or another network adapter]. Click [Devices] tab. NOTE • [Use PPP connection or another network adapter] should be selected for using a LAN card. Otherwise, the LAN card may not work properly. 30 3.
English 4. The “Devices” page is displayed. Double-click [Network]. 5. “Network Configuration” is displayed. Select a network driver for a LAN card. Click [Properties]. 3.
English 6. The connected network adapter’s properties are displayed. [IP Address] tab [Obtain an IP address via DHCP] ...................................Select this to assign an IP address to the unit by a DHCP server. [Specify an IP address] ........Select this to type an IP address. [Name Server] tab ...............Type an IP address for DNS or WINS. Click [OK]. (The message below will be displayed. Please follow the message and complete the settings.
English Connection with a Cisco Aironet 1. Insert the Aironet Card, and “Unidentified PC Card Adapter” is displayed. Driver Name:......................Type “aironet”. Click [OK] when finished. 2. ‘Aironet Wireless LAN Adapter’ settings page is displayed. [IP Address] tab [Obtain an IP address via DHCP] ...................................Select this to assign an IP address to the unit by a DHCP server. [Specify an IP address] ........Select this to type an IP address. [Name Server] tab...............
English Click [OK]. (The message below will be displayed. Please follow the message and complete the settings.) Click [OK] to return to the “Terminal Connection Manager” dialog box. 3. Press “F2” key in the “Terminal Connection Manager”. 4. “Terminal Properties” is displayed. Click the [Network] tab. 5. The “Network” page is displayed. Select [Use PPP connection or another network adapter]. Click [Devices] tab.
English NOTE • Double-click the [CISCO Aironet] icon on the “Devices” tab and set the detailed utility as needed. Refer to the instruction of the LAN card for details. Click [OK] to save the settings and close the “Terminal Properties” dialog box. This completes the LAN card settings. 3.
English 3-3. Dial-Up Connection The following details the installation of a dial-up connection for RAS (Remote Access Service). No restriction of the protocol is made for the “Dial-up connection”. To use a dial-up connection requires an RAS server in operation. [Dial-up Connection] Telephone Lines RAS Server WTS 630L WTS FTP Server NOTE • Another type of connection using a modem, a dial-in connection, is available to connect to the WTS with an ICA protocol. Please refer to the page 49.
English 2. “Terminal Properties” is displayed. Click the [Network] tab. 3. The network setting window is displayed. Select [Use PPP connection or another network adapter]. Click [PPP] tab when finished. 3.
English 4. The dial-up setting window is displayed. NOTE • Enter your information in the pertinent fields. [Connection Name].............Choose a connection name for a dial-up connection. ([None] indicates no connection name chosen.) [New...]...............................Click the button to create a new dial-up connection name. “Create New Dial-Up Connection” dialog box is displayed. Enter the name and click [OK]. [Remove] ............................Delete the connection name displayed currently.
English [Dialing Properties...] ...................................Click the button to set information of the sender. [When dialing from:] ..........Choose the sender’s location. [New...]...............................Click this to add a new sender’s location. “Create New Location” dialog box is displayed. Enter a new sender’s location and click [OK]. [Remove] ............................Remove the current sender’s location. [Local Settings are...] [The local area code is:], [The local country code is:] ..
English [Device Configure...] ...................................Click the button the detailed settings of the modem. (Please refer to the instruction manual of a modem for settings of the modem.) [Port Settings] tab [Manual Dial (user supplies dial strings)] ...................................Click this box to set up for manual dialing. [Terminals] [Use terminal window before / after Dialing] ...................................Click this box to record terminal window information before or after dialing.
English NOTE • When changing settings in the [Device Properties], click the [Call Option] tab before clicking [OK] to close the window. [TCP/IP Settings...] Click the button to set the TCP/IP settings of the WTS. [Use server-assigned IP address] ...................................Click the box to use a server-assigned IP address. [Specify an IP address] ........Enter a provided IP address. [Use server-assigned DNS or WINS server IP address] ...................................
English [Primary DNS], [Secondary DNS] ...................................Enter IP address of the primary DNS and IP address of the secondary DNS. [Primary WINS], [Secondary WINS] ...................................Enter IP address of the primary WINS and IP address of the secondary WINS. [Use software compression] ...................................Click to use software compression. [Use IP header compression] ...................................Click to IP header compression. [Use default gateway].........
English 4. ADDING & CHANGING A CONNETION NAME This chapter shows how to add, delete, and modify connection names to a WTS. All the settings are managed in the “Terminal Connection Manager”. 4-1. Adding a Connection Name These are settings for the Server connection. Each protocol has different settings. Please install the appropriate settings.
English In Use of RDP Protocol 1. Display [Terminal Connection Manager]. Click the [Configure] tab and [Add...] to set the connection information of the WTS. 2. Protocol selection dialog box is displayed. Select the “Microsoft Remote Desktop Client” (RDP) Click [OK] when finished. 44 4.
English 3. “WTS Connection Wizard” is displayed. [Name]................................Type the connection name to the Server. Name the connection to differentiate the Server from others. [Server] ...............................Type the IP address or the name of the Server, or WINS setting is necessary when the name is typed. [Low Speed Connection].....Click the check box when making a low speed connection.
English 4. Automatic Logon setting page is displayed. Type the name, the password, and the domain name of the WTS beforehand to enable an Automatic Logon to the WTS after connecting. NOTE • If an Automatic Logon is not needed, click [Next>]. Click the check box of the [Automatic Logon] to enable the item. [Username]..........................Type the name to connect the WTS. [Password] ..........................Type the password for the user name. [Domain] ............................Type the domain name.
English 5. Specifying an application to run after connecting to a WTS is displayed. Select whether to display the Windows desktop screen or start up an application. [Desktop] ............................Select this to start the Windows desktop screen when you connect. [Application file name:] .....Select this to start an application when you connect. [Working directory:] ...........Input the name of the application and the working directory if necessary.
English 6. The last page of the “WTS Connection Wizard” is displayed on the screen. Click [Finish] to return to the “Terminal Connection Manager” dialog box. The registered connection name is displayed in the “Terminal Connection Manager” dialog box. This completes the setup of the 630L for connection to a WTS with the RDP protocol. NOTE • Please repeat step 1 to 6 to entry more than two kinds of connections. 48 4.
English In Use of the ICA protocol 1. Click the [Configure] tab. Click [Add...]. 2. “New Connection” dialog box is displayed on the screen. Select “Citrix ICA Client” (ICA). Click [OK] when finished. 4.
English 3. “Specify Connection Type” dialog box is displayed. [Network Connection]........Select for network connection. [Dial-In Connection] ...........Select for dial-in connection. Click [Next>] when finished. Go to step 4 when selecting [Network Connection]. Go to step 5 when selecting [Dial-In Connection]. 4. Citrix Server or published application selection page is displayed. 1) Select [Citrix Server (WTS) ] or [Published Application]. 2) Click [Server Location…]. 50 4.
English [Server Group]................Select the WTS Group to connect. (A WTS Group consists of [Primary], [Backup 1], and [Backup 2]. The WTS will be searched in order of [Primary], [Backup 1], and [Backup 2]. [Add]...............................Add another Server address. Type the Server Name or IP address. (The typed Server Name or IP address will be shown in the [Address] list. [Delete]...........................Delete the selected WTS from the [Address] list. [Default List] ...................
English 5. “Dial-In Devices” dialog box is displayed. NOTE • Enter your information in the pertinent fields. • A dial-in connection is not available during a dial-up connection. Disconnect the dial-up connection before making dial-in connection. [Dial-In Device:]..................Select the device name connected to the modem. [Phone Number] .................Enter a country code, an area code, and a phone number for the connection. [Use Tone Dialing] ..............Click to use tone dialing. [Configure] ..
English [Connection Preference] [Baud Rate].........................Set the data transmission rate from 110 to 115,200. [Data Bits]...........................Set the data bits. [Parity]................................Set to check the data’s appropriate transmission. [Stop Bits] ...........................Set the length of the Stop Bits. [Flow Control]....................Set Flow Control. [Call Option] tab [Cancel the call if not connected within] ...................................
English 6. A title for the ICA connection page is displayed. Type a connection name of the WTS. Click [Next]. 7. An application selection page is displayed. Specify the command line and the working directory of an application to operate. NOTE • Leave these fields blank and click [Next>] to run a Windows desktop. [Command Line:]................Type the application name and the path. [Working Directory:] ..........Type the working directory for the application.
English 8. Automatic logon settings page is displayed. Type the name, the password, and the domain name of the WTS beforehand to enable an Automatic logon to the WTS after connecting. NOTE • If an Automatic Logon is not needed, click [Next.] [User Name:].......................Type the name to automatically connect the WTS. [Password:] .........................Type the password for the user name. [Domain:] ...........................Type the domain name. Click [Next>] when finished. 9.
English 10. Compression, encryption, and sound settings page is displayed. [Use Printer Configuration Utility] ...................................Click the check box to install the printer at the [ICA Client Printer Configurations]. [Compress Data Stream] .....Click the check box to reduce the amount of data transferred between the WTS and the 630L, which can increase performance. (If you have sufficient bandwidth, leave compression off to conserve processing power on the WTS.) [Enable Sound:]...........
English [Encryption Level:] .............Encryption level can be selected from RC5 (128 bit Login Only), basic, RC 5 (40 bit), RC5 (56 bit), RC5 (128 bit). The level becomes higher as the bit gains. RC5 (128 bit - Login Only) indicates the 128 bit level security available only at logon. Click [Next>] when finished. 4.
English 11. Firewall settings page is displayed. NOTE • These settings are effective when connecting to the WTS through internet. • If no change is made, the settings under the [Firewall settings] of [Global ICA Client Settings] will be applied (refer to page 89 for details). [Use alternate address for firewall connection] ...................................Click the check box to connect to the WTS through the Firewall.
English This completes the setup of the 630L for connection to a Server with the ICA protocol. NOTE • Please repeat the step 1 to 11 when you adding another connection name. 4.
English 4-2. Deleting a Connection This function deletes an existing Connection Name. 1. Display the “Terminal Connection Manager” dialog box. 2. Click the [Configure] Tab. 3. Select the Connection Name you want to delete. 4. Click [Delete]. 5. “Confirm Connection Delete” dialog box is displayed. Click [Yes] to delete the information of the selected WTS. 60 4.
English 4-3. Editing a Connection This function modifies attributes of the WTS connections. 1. Display the “Terminal Connection Manager” dialog box. 2. Click the [Configure] Tab. 3. Select the connection you want to modify. 4. Click [Edit...]. 5. [Edit Connection] dialog box or [Edit Connection Details] is displayed. • For RDP Connection (Please refer to pages 44 to 48for each setting.) [Net Connections] tab........Change connection settings to a WTS. [Application] tab................
English • For ICA Connection (Please refer to pages 49 to 58 for each setting.) [Server/Dial-In] tab .............Either Server or Dial-In tab is displayed depending on the connection type. [Server] Tab (for LAN connection) To change the WTS / the public application to use [Dial-In] Tab (for Dial-In connection) To change settings of the Dial-In connection [Application] tab.................To change a description of an application to run [Logon] tab .........................
English NOTE • When changing settings in the Dial-In connection, click and show the [Call Option] tab of [Device Properties] of the [Dial-In] tab before clicking [OK] to close the window. 4.
English 4-4. Setting an Autostart Connection This function configures a connection to start automatically each time the 630L is turned on. (This function is available for a LAN connection.) 1. Display the “Terminal Connection Manager” dialog box. 2. Click the [Configure] tab. 3. Select the desired Connection Name for Autostart Connection. 4. Click [Startup...] 5. “Connection Startup” dialog box is displayed. Select [Automatically start the selected connection at startup.
English 5. LOGON & LOGOFF This chapter shows how to log on to and log off from a WTS. 5-1. Logon to a WTS / Logoff from a WTS Logon to a WTS 1. Turn on the 630L. 2. “Terminal Connection Manager” dialog box is displayed. Please follow the direction depending on the environment of the 630L. 5.
English (1) To connect and log on to a WTS through local network: Go to step 3. (2) To connect and log on to a WTS with dial-up connection: Click an active button of a small window on the right bottom of the screen. A dial-up connection is made by clicking the button. Check the clock’s running, and go to step 3. (3) To connect and log on to a WTS with dial-in connection: Go to step 3. (Ask your system administrator for an installation of a dial-up connection.) 3. Click the [Connections] tab.
English Multi Session You can log on to the WTS with the several connection names, and switch the active sessions. • Logon 1. Log on with a Connection Name, as following the previous steps. 2. Press [Ctrl] + [Alt] + [End] keys after logon. 3. “Terminal Connection Manager” is displayed. Select another Connection Name to log on to, and click [Connect]. (Or double click the connection name.) 4. “Log On to Windows” dialog box is displayed after connecting to the WTS.
English Logoff from the WTS If your 630L starts its operation with a desktop 1. Log off from the WTS. (1) Close all applications. (2) Select [Start] on the taskbar. (3) Microsoft Windows NT Server 4.0 Terminal Server Edition: Select [Logoff]. Microsoft Windows 2000 Server / Advanced Server / Datacenter Server: Select [Shut Down...] and select [Logoff] of the [Shut Down Windows] dialog box. (4) Click [OK] on the Logoff Window. The session ends and automatically logs off from the WTS.
English If your 630L starts its operation with an application 1. Log off from the WTS. Close applications to log off from the WTS. “Terminal Connection Manager” is displayed. If a dial-up connection is running, click the active button of the window on the right bottom of the screen. Clicking the button Disconnects the dial-up connection. 2. Shut down the 630L. (Please refer to the previous page for shutting down the 630L.
English 5-2. Opening/Closing a Local Web Browser Opening a Local Web Browser 1. Turn on the 630L. 2. “Terminal Connection Manager” dialog box is displayed. Please follow the directions relevant on the environment of the 630L. (1) If the web server is on the same network (Intranet): Go to step 3. (2) If the web server is not on the same network, and a dial-up connection is needed (Internet): Click an active button of a small window on the right bottom of the screen.
English Closing a Local Web Browser 1. Close the local web browser. Select [Exit] under the [File] on the menu bar and close the local web browser. (Or click the close button on the title bar of the browser.) Return to the “Terminal Connection Manager” dialog box. If a dial-up connection is being made, click the active button of the window on the right of the screen. Clicking the button Disconnects the dial-up connection. 2. Shut down the 630L. There are three ways to shut down the unit.
English 6. USING THE TERMINAL PROPERTIES This chapter presents how to modify all settings of the 630L using the “Terminal Properties”. To display the “Terminal Properties” during logging on, press F2 in the “Terminal Connection Manager” dialog box. (Press Ctrl + Alt + End to display the “Terminal Connection Manager”.) 6-1. General Information & Reset to Default Click [General] tab to confirm general settings and to reset the 630L to factory-default settings. Product Information [Product Name] ...........
English Resetting to Default 1. Click [Reset the terminal to factory-default property settings] check box. 2. The “System Settings Change” dialog box is displayed. Click [Yes]. 3. “Terminal Properties” is displayed. Click [OK]. “Terminal Setting Change” dialog box is displayed. Click [Yes] to restart the terminal. “WBT Setup Wizard” will be displayed after restarting the terminal. 6.
English 6-2. Input Devices Settings Click the [Input] tab to modify keyboard, NumLock Key, and mouse characteristics. Keyboard Settings [Keyboard] [Locale]...............................Selects a keyboard language. [NumLock Enable on Boot UP] ...................................enables/cancel NumLock function on start-up. [Character Repeat] [Repeat delay] ....................Allows adjusting the amount of time that elapses before begins repeating when you hold down a key. [Repeat rate] ....................
English Mouse Settings Click [Properties...] to display the [Mouse Properties] [Button Configuration] .......Assigns the primary mouse button and the secondary mouse button. [Speed] ................................Adjusts the speed at which the pointer moves on your screen. [Acceleration] .....................Adjusts how fast the mouse pointer accelerates as you move the mouse. Click [OK] to save the settings and return to the “Terminal Properties”.
English 6-3. Colors & Power Save Settings Click the [Display] tab to modify display parameters such as colors, screen saver, and power save. Resolution and Colors [Desktop Area and Colors] [Details] ..............................Adjusts the resolution and colors of the screen. Screen Saver [Screen Saver] [Enable Screen Saver] ..........Click the [Enable Screen Saver] check box and set an idle period from 1 to 60 minutes before Screen Saver starts in minutes.
English Brightness [Contrast/Brightness] [Settings] .............................Enables to adjust the brightness of the screen. [Enable Contrast/Brightness control from Keyboard] Enables to adjust the brightness/contrast from a Keyboard. • [Alt] key and [+] key: The brightness of the screen increases. • [Alt] key and [-] key: The brightness of the screen decreases. Click [OK] to close “Terminal Properties” and save the adjustments.
English 6-4. Network Settings Click [Network] tab to set network information for the 630L. NOTE • All settings shown here are previously adjusted on the “WBT Setup Wizard”. • Please set the properties depending on the 630L connection settings. [Use PPP connection or another network adapter] ...................................Click to use a modem connection to the WTS. To connect to the WTS with a LAN network, set the following. [Obtain an IP address from a DHCP server] ...................................
English [DHCP Options...]..............Click this to receive essential information about the 630L from the DHCP server every time the 630L is turned on. Refer to “Practical Setup” on page 100 for details. [Advanced Network...] .......Allows setting for DNS/WINS service. A DNS/WINS server is required for the setting. [Enable DNS]......................Click the check box and type default domain name and IP address of the DNS server. [Enable WINS] ...................
English NOTE • The [Terminal Settings Change] dialog box will not be displayed when [Terminal Name], [DHCP Options], and [Advanced Network…] are changed, though the unit needs to be restarted to set the adjustment effective. 80 6.
English 6-5. Printer Settings NOTE • The 630L supports a LPT1 port and a COM1 port. • Use a RDP protocol to set the printer's adjustment. If you are using the ICA protocol, please refer to the instruction manual of the Citrix MetaFrame. Click [Printers] tab You can add, delete and change the settings of the printer in this section. 6.
English Adding another printer settings This enables to add a printer when no printer is connected to the LPT1 port and 1. Select LPT1 and click [Add]. 2. “Printer Properties” dialog box is displayed. [Friendly Name]..................Name the printer or use the indicated name. (Some programs do not support server and printer name combinations of more than 31 characters.) [Manufactures] [Printers] .............................Select the manufacturer and model of your printer.
English Modifying the settings This enables to delete printer settings when a printer is connected to the LPT1 port. 1. Select LPT1 and click [Properties...]. 2. “Printer Properties” dialog box is displayed. Change the settings as needed. [Friendly Name]..................Changes the printer's name. (If you are naming the printer, the name combination must be 31 character or less.) [Manufacture] [Printers] .............................Change the Manufacture and the model name of the printer.
English 6-6. Browser Settings Click [Web] tab to adjust the browser settings of 630L. [Enable Web Connection] ...Click the check box for web connection. [Home page:] ......................Type the URL for the page when “Home” button of the browser is clicked or each time you start the Internet Explore. [Search page:]......................Type the URL for the page when “Search” button of the browser is clicked. [Persistent browser cache]...
English [Preference] .........................Click here to set hyperlink and font size. [When do you want the browser to underline hyperlinks?] ...................................Select when you want the hyperlinks to be underlined. [What size font do you want to use?] ...................................Select the font size of the web page. [Dial-up information] .........Click this to setup connection. (This button is displayed only when a dial-up connection is set. Please refer to page 36.
English [Proxy Information] ............Click this for proxy settings. [Access the Internet using a proxy server] ...................................Click the check box if you use proxy server for the web browser connection. [Proxy server name or IP address:] ...................................Type the name of the computer running the proxy server. [Port] ..................................Type the port number. [Bypass proxy server for local (Intranet) addresses.] ...................................
English 6-7. Dial-Up (PPP) Connection Settings Click [PPP] tab to adjust the dial-up settings of 630L. The following details the installation of a dial-up connection to a WTS or a Web Server. (To use a dial-up connection requires an RAS server in operation.) Please refer to page 36 for each setting. 6.
English 6-8. ICA Settings Click [ICA] tab to confirm information about Citrix ICA Client version and to change the settings when connecting to the Citrix Server with ICA protocol. NOTE • The ICA settings are effective only when the unit is connected to the WTS with ICA protocol. Also, the settings will affect all the settings with ICA protocol. Confirming Citrix ICA Client information [Client Software].................Version of the Citrix ICA Client 88 6.
English General Settings of the ICA Connection You can change the settings for the ICA Connection. 1. Click [Settings...]. 2. “Global ICA Client Settings” dialog box is displayed. [Hotkeys] tab......................Enables to change the hotkeys when logging on to the Server. There are the hotkeys to control the 630L and the ones same as standard Windows hotkeys. Please refer to the instruction manual of the Citrix MetaFrame for details. NOTE • No hotkeys are set in the 630L in the factory default.
English [Firewall Settings] tab ...................................Change the settings of Firewall and SOCKS proxy server. This setting change is displayed when adding a new connection. NOTE • If connecting a WTS through internet, the settings should be completed before the WTS is selected. • If you configure a default SOCKS proxy server, you must specify at least one WTS in the [Server Location] tab for a WTS and published application browsing to work.
English 6-9. Device Settings Click [Device] tab to confirm and set LAN card properties and speakers of the 630L. Network Adapter Settings Configure the properties of the network drivers installed on your device. Please refer to page 29 for details. 6.
English Sound Settings Configure the sound properties of the 630L. 1. Double-click the “Volume & Sounds” icon. 2. “Volume & Sounds Properties” is displayed. [Volume] tab.......................Click the check boxes to enable sounds for events, applications, and notifications. [Sounds] tab........................Select sounds for each cases. Click [OK] to return to the “Terminal Properties” dialog box. Click [OK] to save the settings and close the “Terminal Properties” dialog box. 92 6.
English Date/Time Settings Configure the date/time properties of the 630L. NOTE • The settings are referred when the client time zone function of the ICA protocol is effective. • Date and time will return to the default settings if the power cord is unplugged. 1. Double-click the “Date/Time” icon. 2. “Date/Time Properties” is displayed. [Date/Time] Tab .................Set date, current time, or time zone. During daylight saving time, click the [Daylight savings time currently in effect] check box.
English 6-10. Product Information, Security, & Updating Software Click [System] tab to confirm information about the 630L, to set the security, and to update firmware. Product Information [Software] [Microsoft Windows CE] ...................................Microsoft Windows CE Version, Revision [Windows Terminal Server Client] ...................................Window Terminal Server Client Revision [Boot software] ...................
English Security Settings This enables settings on network information of the WTS invisible to prevent from undesirable change. When the security is active, the following settings become. • “Terminal Connection Manager” * [Configure] tab • “Terminal Properties” * [General] tab... [Reset the terminal to factory - default settings] * [Network] tab * [Printers] tab * [PPP] tab * [ICA] tab * [System] tab... [Update...], [Security] PROCEDURE 1. Click the [Security Enable] box. 2. Click [Setting Password...
English CANCELING SETTINGS 1. Display “Terminal Connection Manager”. 2. Press [Ctrl], [A], and [F2] at the same time. 3. “Enter Security Password” dialog box is displayed. [Password:] .........................Enter the password Click [OK] on [Enter Security Password] when finished. 4. All settings in the “Terminal Properties” will be active. Click the [Security Enable] check box on the [System] tab to remove the check mark.
English Software Updating You can update the built-in software. NOTE • Before updating, please complete the following: * Copy the update file (*.bin) to the accessible file folder of the FTP Server. * If the WTS is connected with LAN, close all the connection to the FTP Server. * Make a dial-up connection if it is adopted to connect the WTS. Software Updating is not available if a dial-in is adopted to connect the WTS. 1. Click the [Update...] of [Software]. The following message appears.
English [User Name:].......................Type the user name to connect the FTP Server. [Password:] .........................Type the password for the user name to connect the FTP Server. [File Name:] ........................Type the folder and copied file name located in the FTP Server. Type the file name as indicated below if the file is in the “update folder” in the “software folder”: \software\update\*.bin NOTE • Clicking the "Execute automatic software update.
English 4. Click [Download]. The following message is displayed when you successfully download the software. Click [OK] and restart the 630L. NOTE • Failing to download results in program's returning to the "Software Update" dialog box. * In case of returning to the "Software Update" dialog box, confirm such as network settings and redo the [Settings] before clicking [Download].
English 7. PRACTICAL SETUP By utilizing the DHCP Option function of the DHCP Server, necessary information is supplied by the DHCP Server, and each setting is automatically set every time the unit is turned on. The following information can be obtained by the 630L. • WTS/Web Server Connection Settings • Automatic Software Update • Security Settings • Administration Console Setting NOTE • For DHCP Option settings, confirm the following: * The 630L is connected to the WTS/Web server through built-in LAN.
English ICA Tab Device Tab Hotkeys Disable Colors 256 colors Client Name eClient******(Last 6 digits of the Mac address) Server Location Automatically Found Firewall Settings Disabled Volume Maximum Enable Sounds for: Events, Applications, Notifications Scheme No Sounds Date January 1st, 2001 Time Start at 00:00:00 Time Zone (GMT-8:00) Pacific Time (US & Canada) NTP Server Does not Synchronize Time 7.
English DHCP Server Settings Please open DHCP settings to configure each DHCP Option as follows. [Key] ...................................Set the value as “EIZO”. (The 630L will not accept any value but “EIZO”.) [Server] ...............................Type an IP address of the Server installing an update file and a registry file of the 630L. [User Name]........................Type the user name to logon to the FTP Server. [Password] ..........................Type the password for the user name.
English NOTE • Making a Registry File to Connect to a WTS/Web Server. Please refer to the example below, make a registry file, and save it in Unicode format. Please change the italic bold phrases as necessary. - ConnectionName : Type the connection name in the “Terminal Connection Manager”. - TerminalServerAddress : Type the IP address or the full domain name of the WTS. - URL : Type the URL of the Web Server. (Including “http://”.) Registry file ...........................................................
English "StartCmdLineArgs"="/L "ConnectionName"" ......... Command argument to connect to a WTS "StartExe"="WFICACE" ............................. Fixed – Command (executable file) to connect to a WTS "ScreenPercent"="100" ............................ Fixed – Assign the ratio of the 630L screen to the displayed Window of the WTS. Name displayed on the Connection Manager "Description"="ConnectionName" ................... "Address"="TerminalServerAddress" ................
English 630L Settings The 630L’s default setting is set to enable DHCP Options. There is no need for extra settings. After initial setup, confirm the following: • [Use PPP connection or another network adapter]in the [Network] tab of “Terminal Properties” is selected. • Press “DHCP Option” on “Network” tab in the “Terminal Properties”. “DHCP Options” is displayed. [Enable DHCP Option] is selected, and code numbers assigned for the DHCP options.
English 8. TROUBLESHOOTING This page presents problem that can be corrected by the user. If a problem persists even after applying the suggested remedies, contact an EIZO dealer. Problems Points to check with possible solutions 1. No picture is displayed on the screen. Check if the power is OFF. Check brightness setting. Minimum settings will cause screen to be blank. Try pressing a key on the keyboard, or clicking the mouse. (The monitor may be in a power saving mode.) 2.
English NOTE • Please do not connect and disconnect repeatedly a keyboard or a mouse while the 630L is in operation, as the 630L may cause the unit damage. 8.
English 9. CLEANING Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime. NOTE • Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl alcohol), abrasive cleaners, or other strong solvents, as these may cause damage to the cabinet or LCD panel. Cabinet To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild detergent. Do not spray wax or cleaner directly onto the cabinet.
English Mouse If you find that the pointer on the screen doesn’t move smoothly, your mouse needs to be cleaned. Periodically clean the mouse for your operation. (1) Turn off the 630L. (2) Turn the mouse upside down and remove the mouse trackball cover. Press the cover towards “Open” while pulling the other side of the cover. Press (3) Remove the trackball. (4) Wipe the trackball with a soft cloth with neutral detergent. (5) Clean all the rollers, getting all the lint off of them.
English 10. SPECIFICATIONS CPU and Memory Display CPU Memory LAN National Semiconductor Geode GX1, 300 MHz RAM; 64 MB, ROM;32 MB 10BASE-T/100 BASE-TX, Wake On LAN supported Speakers Output Level: LCD Panel 38 cm (15 inch) TFT color LCD panel Anti-Glare Hard Coating (Viewing Angle: Horizontal; 160°, Vertical; 150°) Dot Pitch 0.297 mm x 0.297 mm Resolution 1024 x 768 Viewable Image Size 304.1 mm (H) x 228.1 mm (V) (11.9" (H) x 8.
English Weight 5.2 kg (11.5 lbs.) (without the tilt stand Environmental Specifications Temperature Humidity 4.0 kg (8.8 lbs.)) Operating: 0°C to 35°C (32°F to 95°F) Storage: -20°C to 60°C (-4°F to 140°F) 30 % to 80 % R.H.
English 11. REFERENCE 11-1. Attaching an Arm Stand The 630L can be used with an arm stand by removing the tilt stand and attaching the arm stand to the terminal. NOTE • Use an arm stand that satisfies the following. - When using the 630L with an arm stand, the arm stand must be VESA approved : Use an arm stand with a 75 mm x 75 mm hole spacing on the arm mounting pad. Use an arm stand that is able to support an object weighing 8.0 kg. A GS approved arm stand.
English 3. Attach an arm stand to the 630L securely. WARNING Install the unit securely when attaching to an arm stand. When attaching an arm stand, please refer to the user’s manual of the arm stand and install the unit securely with the enclosed screws. Not doing so may cause the unit to come unattached, which may result in injury or equipment damage. When the unit is dropped, please ask your dealer for advice. Do not continue using a damaged unit.
English INDEX A H ADDING & CHANGING A CONNETION NAME ...................................................43 Administration Console ............................96 Application to Run..............................47, 54 Attaching an Arm Stand ......................... 112 Automatic Logon ................................46, 55 Autostart Connection ...............................64 Hotkeys ....................................................89 B K Brightness ............................................
English R RAS..........................................................36 RDP ...................................................43, 44 Reference .............................................. 112 Resetting to Default .................................73 Resolution ..........................................18, 76 S Screen Saver ...........................................76 Security Settings......................................95 Serial Port ..................................................