SAFETY SYMBOLS PRECAUTIONS 1. INTRODUCTION 1-1.Features 1-2.Package Contents 1-3.Controls & Connectors 2. CABLE CONNECTION 2-1.Before Connecting 2-2.Connecting the Signal Cable (D-Sub or DVI) 2-3.Connecting the Signal Cable (ADC) 2-4.Connecting Two PCs to the Monitor 2-5.How to remove the Tilt Stand 3. ScreenManager 3-1.How to use the ScreenManager 3-2.ScreenManager Adjustments and Settings 3-3.FineContrast 3-4.Useful Functions 4. ADJUSTMENT 4-1.Screen Adjustment 4-2.Displaying a low resolution 4-3.
8. CLEANING 9. SPECIFICATION 10.
This manual uses the safety symbols below. They denote critical information. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety. Copyright© 2005-2006 EIZO NANAO CORPORATION All rights reserved.
ScreenManager, ColorEdge and EIZO are registered trademarks of EIZO NANAO CORPORATION in Japan and other countries. As an ENERGY STAR® Partner, EIZO NANAO CORPORATION has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
IMPORTANT! ● ● This product has been adjusted specifically for use in the region to which it was originally shipped. If operated outside the region to which it was originally shipped, the product may not perform as stated in the specifications. To ensure personal safety and proper maintenance, please read this section and the caution statements on the unit (refer to the figure below).
Refer all servicing to qualified service personnel. Do not attempt to service this product yourself as opening or removing covers may result in fire, electric shock, or equipment damage. Keep small objects or liquids away from the unit. Small objects accidentally falling through the ventilation slots into the cabinet or spillage into the cabinet may result in fire, electric shock, or equipment damage. If an object or liquid falls/spills into the cabinet, unplug the unit immediately.
Use the enclosed power cord and connect to the standard power outlet of your country. Be sure to remain within the rated voltage of the power cord. Not doing so may result in fire or electric shock. Power supply: 100-120/200-240 VAC±10 %, 50/60 Hz To disconnect the power cord, grasp the plug firmly and pull. Tugging on the cord may damage and result in fire or electric shock. The equipment must be connected to a grounded main outlet. Not doing so may result in fire or electric shock.
When attaching an arm stand, please refer to the user’s manual of the arm stand and install the unit securely. Not doing so may cause the unit to become unattached, which may result in injury or equipment damage. When the unit is dropped, please ask your dealer for advice. Do not continue using a damaged unit. Using a damaged unit may result in fire or electric shock. When reattaching the tilt stand, please use the same screws and tighten them securely.
Do not block the ventilation slots on the cabinet. * Do not place any objects on the ventilation slots. * Do not install the unit in a closed space. * Do not use the unit laid down or upside down. Blocking the ventilation slots prevents proper airflow and may result in fire, electric shock, or equipment damage. Do not touch the plug with wet hands. Doing so may result in electrical shock. Use an easily accessible power outlet.
The LCD panel is manufactured using high-precision technology. However, note that the appearance of any missing pixels or lit pixels does not indicate damage to the LCD monitor. Percentage of effective pixels:99.9994%or higher. The backlight of the LCD panel has a fixed life span. When the screen becomes dark or begins to flicker, please contact your dealer. Do not press on the panel or edge of the frame strongly, as this may result in damage to the screen.
Thank you very much for choosing an EIZO Color Monitor. ● ● ● ● ● ● ● ● ● ● ● The exclusive use calibration software calibrates the monitor characteristics and generate color profile. Dual inputs compliant DVI Digital input (TMDS) compliant. ADC (Apple Display Connector) inputs compliant.
* Please retain the packing materials for future transference. * The "ActiveRotationII Utility" (for Windows) is included in the EIZO LCD Utility Disk. Please refer to the readme.txt in the EIZO LCD Utility Disk for the details.
Off Power off *1 The main menu of ScreenManager and the FineContrast menu cannot be displayed at the same time. *2 Directly pressing the left button or the right button allows you to select a FineContrast mode. Directly pressing the up button or the down button allows you to adjust the brightness of the screen. *3 Blue lighting, when the screen is displayed (Operation mode), is made to nonlight, see "Power Indicator " Regarding the power indicator for the "Off Timer", see "3-4. Useful Functions".
*5 Allows for connection of a security cable. This lock supports Kensington's MicroSaver security system. For further information, please consult: Kensington Technology Group 2855 Campus Drive, San Mateo, CA 94403 USA Tel: 800-650-4242, x3348 Intl: 650-572-2700, x3348 / Fax: 650-572-9675 http://www.kensington.
Before connecting your monitor to the PC, change the display screen settings (resolution and frequency) in accordance with the APPENDIX charts. * When your computer supports VESA DDC, the suitable resolution and the refresh rate are set by just plugging your monitor into the computer without any manual settings. * Be sure that the power switches of both the PC and the monitor are OFF. 1.
Signal Cable Signal Cable (FD-C16 enclosed) Connector on PC Video Output Connector / D-Sub mini 15 pin Input Connector (monitor) / DVI PC Standard graphics card Macintosh G3 (Blue & White) /Power Mac G4 (VGA) Signal Cable (FD-C16 enclosed) +Adapter* Video Output Macintosh Connector / D-Sub 15 pin Input Connector (monitor) / DVI *Macintosh Adapter (Optional) Digital Input Signal Cable Signal Cable (FD-C39 enclosed) Connector on PC Video Output Connector / DVI Input Connector (monitor) / DVI PC Digital
* The cables are recommended to lead with slight sag for the smooth motion of the stand and the Portrait/Landscape display. 4.Plug the other end of the power cord into a power outlet. The monitor's power indicator will flash yellow slowly. WARNING Use the enclosed power cord and connect to the standard power outlet of your country. Be sure to remain within the rated voltage of the power cord. Not doing so may result in fire or electric shock. The equipment must be connected to a grounded main outlet.
5.Turn on the monitor's power button and then switch on the PC's power. The monitor's power indicator will light up (blue). If an image does not appear, refer to the "7. TROUBLESHOOTING" for advice. Whenever finished, turn off the PC and the monitor. * When turning on the monitor, the kind of the input signal (Signal1 or 2/Analog or Digital) is displayed for a few seconds on the right top corner of the screen. * Adjust brightness of the screen depending on the brightness of your environment.
Signal Cable Signal Cable (FD-C39 enclosed) +ADC-DVI display adapter (commercially available) Connector on PC Video Output Connector / ADC Input Connector (monitor) / DVI PC Power Mac G4 / G5(ADC) * ADC-DVI display adapter is required if the monitor connects to Power Mac G4 / G5. The adapter is commercially available. 2.Plug the power cord into the power connector on the rear of the monitor. 3.Lead the power cord and signal cable into the cable holder at rear of the monitor.
4.Plug the other end of the power cord into a power outlet. The monitor's power indicator will flash yellow slowly. WARNING Use the enclosed power cord and connect to the standard power outlet of your country. Be sure to remain within the rated voltage of the power cord. Not doing so may result in fire or electric shock. The equipment must be connected to a grounded main outlet. Not doing so may result in fire or electric shock. 5.Press the power button while pressing the Input Signal Selection button.
6.Change the input selection setting of the connector in the Input Selection menu to "ADC". Press Enter button to complete the setting and the menu closes. 7.Switch on the PC's power. The monitor's power indicator will light up (blue). If an image does not appear, refer to the "7. TROUBLESHOOTING" for advice. Whenever finished, turn off the PC and the monitor.
Signal Cable (FDC39 enclosed) +ADC-DVI display adapter (EX.1) Digital ADC (commercially available) Signal Cable DD200 [FD-C39](Optional) Signal Cable (FDC39 enclosed) +ADC-DVI display adapter (EX.2) Digital ADC (commercially available) Signal Cable (FDC16 enclosed) Signal Cable (FDC39 enclosed) +ADC-DVI display adapter (EX.3) Digital ADC (commercially available) Signal Cable (FDC16 enclosed) + Adapter* Signal Cable (FDC39 enclosed) (EX.4) Digital DVI-D Signal Cable (FDC39 enclosed) (EX.
Selecting the Active Input The Input Signal Selection button on the control panel can be used to select either SIGNAL 1 or SIGNAL 2 as the active input at any time. Every time the button is pressed, the input changes. When switching the signal, the kind of the input signal (Signal 1 or 2/ Analog or Digital) is displayed for a few seconds on the right top corner of the screen. The Priority Input Signal This function is used to select which PC will have priority to control the monitor when utilizing two PCs.
Manual The monitor will not detect signals automatically in this mode. Select the active input by pressing the input signal selection button on the monitor's control panel. * When "1" or "2" is selected, the power saving mode of the monitor activates only if both PCs are in power saving mode. The LCD monitor can be used with an arm by removing the tilt stand and attaching the arm or stand to the LCD monitor. Using our optional arm or stand is recommended. (Ask your local dealer for information.
1.Hold the center of the stand mounting cover and slide them rightward or leftward to remove the mounting cover. 2.Lay the LCD monitor down. Do not scratch the panel. 3.Remove the tilt stand by loosening the screws. (4 pcs of M4 x 15 BZn/Fe) 4.Attach an arm stand to the LCD monitor securely.
ScreenManager allows you to adjust screen performance though the main menu and select a FineContrast mode easily. * Main Menu and FineContrast menu cannot be activated at the same time. 1.Entering the ScreenManager Press the Enter button once to display the main menu of the ScreenManager. 2.Making Adjustments and Settings (1) Select the desired sub menu icon using the Control buttons and press the Enter button. The sub menu appears.
3.Exiting the ScreenManager (1) To return to the main menu, select the icon or press the Down button twice, followed by the Enter button. (2) To exit the ScreenManager, select icon or press the Down button twice, followed by the Enter button. * Double clicking the Enter button at any time also exits the ScreenManager menu.
Reset PowerManager DVI DMPM VESA DPMS Off Others Screen Size Border Intensity Input Priority Off Timer Beep Menu Settings Menu Size Menu Position Menu Off Timer Translucent ActiveRotation II ** 4-2.Displaying a low resolutions * Select the priority input signal. Set the monitor's off timer to on or off. Set the monitor's beeper to on or off. Change the size of the menu. Adjust the menu position. Set the menu displaying time.*2 Set the transparency of the background. 5.
This function allows you to select the best suited mode for screen display. To select the Mode Directly pressing the Left or Right button allows you to select the best suited mode for screen display from 3 FineContrast modes; sRGB, Custom and CAL. Color settings each mode can be adjusted by using the menu of the ScreenManager. Exit Press the Enter button to exit the menu. FineContrast Mode Selectable FineContrast modes are as follows.
Color Adjustment of the Mode Settings , and settings can be adjusted on the FineContrast menu. Select the desired function icon with the Up/Down Control buttons and adjust with the Left/Right Control buttons. (Setting(s) of and/or is defined as standard default in some modes. Detailed Adjustments The detailed color settings of each mode can be adjusted by using the menu of the ScreenManager.
[To unlock] Switch off the monitor's power by the power button on the front control panel, then hold Down the Auto Adjustment button once again and turn the power back on. Off Timer The off timer function causes the monitor to automatically enter a power off state after a predetermined amount of time has lapsed. This function was created to reduce afterimage characteristics that are particular to LCD monitors when the monitor screen is left on for a long period without use.
* The off timer function works while the PowerManager is active, but there is no advance notice before the monitor's power is switched off. Power Indicator setting Light off the power indicator. This function is available for the multiple panels settings. [Procedure] (1) Select in the ScreenManager menu. (2) Select "Disable". EIZO Logo Appearing Function When switching on the power button on the front control panel, the EIZO logo is displayed for a while.
The monitor displays the digital input image correctly based on its pre-setting data. Analog Input Screen adjustments for the LCD monitor should be used in suppressing screen flickering and also for adjusting the screen to its proper position. There is only one correct position for each display mode. It is also recommended to use the ScreenManager function when first installing the monitor or whenever changing the system.
2.Run the "Screen Adjustment Program". Having read the "Readme.txt" file, run the "Screen Adjustment Program" in the enclosed EIZO LCD Utility Disk. Step by step, adjustment is provided by the wizard guide. (If using the Windows, the program can be directly run from the menu screen of the CD-ROM.) * If the user's operating system has no utility disk (e.g. OS/2), we recommend setting the desktop pattern to that as shown in the diagram on the following. 3.Adjust by using menu in the ScreenManager.
(2) Horizontal bars appear on the screen. Use the adjustment. => Select the and eliminate the horizontal flickering, blurring or bars by using the Right and Left buttons. * Horizontal bars may not completely disappear from the screen depending on the PC. (3) The screen position is incorrect. Use the adjustment. => The correct displayed position of the monitor is decided because the number and the position of the pixels are fixed.
(4) Screen image is smaller or larger than the actual screen images. Use the adjustment. => Adjustment is needed when the input signal resolution and the resolution now being displayed are different. Select and confirm if the resolution now being displayed is the same as the input resolution. If it is not, adjust the vertical resolution using the Up and Down button and adjust the horizontal resolution using the Right and Left buttons. 4.
The lower resolutions are enlarged to full screen automatically. Using the function in the menu enables to change the screen size. 1.Enlarge the screen size when displaying a low resolution. => Select the . Select the in the others menu and select the screen size by using the Up and Down buttons. Menu Full Enlarged Normal Function Displays the picture on the screen in full, irrespective of the picture's resolution.
* is disabled when the screen is displayed in the following resolutions. ● ● 1600 x 1200 The image size is doubled both in horizontally and vertially to (i.e. 1600 x 1200 enlarged from 800 x 600) provide clear focus which does not require this function. 3.Set the brightness of the black area surrounding the displayed image. => Set the . In the "Enlarged" mode or "Normal" mode, the outer area (border) is usually black.
Icons Functions "*": Settable/Adjustable "-": Fixed at the factory FineContrast Modes sRGB Custom CAL Brightness** * * - Temperature** - * - - * Saturation - * - Hue - * - - * - * * Gamma** Gain 6 colors Reset - - **These settings can be also adjusted on the FineContrast menu. * Allow the LCD monitor to stabilize for at least 20 minutes before making image adjustments. (Allow the monitor to warm Up for at least 20 minutes before making adjustments.
* The values shown in the Kelvin are available only as a Gamma reference tool. * Adjusting the turns the adjustement "OFF". * Setting the temperature under 4,000 K or over 10,000 K invalidates the color temperature setting. (The color temperature's setting turns "OFF".) To set the gamma value 1.8 ~ 2.6 (in 0.2 increments) * If setting the gamma value, the using the monitor in the Saturation digital signal input is recommended.
The menu in the ScreenManager enables to set the power-save setup. * Do your part to conserve energy, turn off the monitor when you are finished using it. Disconnecting the monitor from the power supply is recommended to save energy completely. * Even if the monitor is in a power saving mode, USB compliant devices function when they are connected to the monitor's USB (both the Upstream and the Downstream ports).
Digital Input This monitor complies with the "DVI DMPM". [Procedure] (1) Set the PC's power saving settings. (2) Select "DVI DMPM" from the menu. [Power saving system] PC Operation Power saving/Off mode Monitor Operation Power saving Power Indicator Blue Yellow [Power Resumption Procedure] Operate the mouse or keyboard to return to a normal screen . Power on the PC to return a normal screen from the Off mode of the PC.
ActiveRotationII function allows you to change the display orientation of the monitor with the panel rotation. Reder to Web site of EIZO NANAO CORPORATION for the latest information about supported graphics card (http://www.eizo.com/). * After changing the display orientation, it may take some time until the screen image is available. * · The ActiveRotationII function may not work correctly using with some graphics card or OS.
2.When the screen image is expanded or contracted, restart the PC. The ActiveRotationII function may not work correctly using with some graphics card or OS. When the screen image remains to be expanded or contracted after restarting the PC, please try to change the screen resolution setting of your PC system. * The "ActiveRotationII Utility" (for Windows) allows you to change the display oriantation easily. Please refer to the readme.txt in the EIZO LCD Utility Disk for the details.
This monitor provides a hub which supports the USB standard. When connecting to a USB compliant PC or another hub, the monitor functions as a hub which the USB compliant peripherals can be easily connected. Required System Environment * PC equipped with USB ports or another USB hub connected to the USB compliant PC * Windows 98/2000/XP//Mac OS 8.5.1 or later * EIZO USB Cable (MD-C93, enclosed) * The USB hub function may not work properly depending on the PC, OS or peripherals.
2.Connect the upstream port of the monitor to the downstream port of the USB compliant PC or another hub by using the USB cable. After connecting the USB cable, the USB function can be set up automatically. 3.After setting up, the monitor's USB hub is available for connecting USB compliant peripherals to the downstream ports of the monitor.
If a problem persists even after applying the suggested remedies, contact an EIZO dealer. ● ● ● ● No picture problems : See No.1 ~ No.2 Imaging problems : See No.3 ~ No.14 Other problems : See No.15 ~ No.18 USB problems : See No.19 ~ No.20 Problems 1. No picture [] Indicator status: Off Indicator status: Blue Indicator status: Yellow [] [] [] Indicator status: Slowly flashing Yellow 2. Following messages appear. (Error messages shown below will remain on the screen for 40 seconds.
Whenever an error signal message appears, the signal frequency will be displayed in red. (Example) [ ] Use the graphics board's utility software to change the frequency setting. (Refer to the manual of the graphics board.) 3. Display position is incorrect. [ ] Adjust the image position using the . [ ] If the problem persists, use the graphics board's utility software to change the display position if available. 4. Screen image is smaller or larger than the actual screen images.
7. Horizontal bars of distortion appear. [ ] Decrease the horizontal bars using the . 8. Letters and lines appear blurred. [ ] Adjust the blurred lines using . 9. Distortion appears like the [ ] This happends when both composite (X-OR) input signal and separate vertical figure below. synchronizing signal are input. Please select one of the two. 10.The screen is too bright or too dark. 11. Afterimages appear. 12.The screen has defective pixels (e.g. slightly light or dark).
15.The cannot be selected. 16.The Main menu of ScreenManager does not operate. [ ] is disabled when the screen is displayed in the 1600 x 1200. [ ] is disabled when "Normal" is selected in the menu. [ ] The image size is doubled both in horizontally and vertically to (i.e. 1600 x 1200 enlarged from 800 x 600) provide clear focus which does not require this function. [ ] The adjustment lock is probably on. To unlock: switch the LCD monitor off.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime. * Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl alcohol), abrasive cleaners, or other strong solvents, as these may cause damage to the cabinet or LCD panel. Cabinet To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild detergent. Do not spray wax or cleaner directly into the cabinet. (For details, refer to the manual of the PC.
54 cm (21.3 inch), TFT color LCD panel with Anti-Glare Hard Coating LCD Panel Viewing Angle: H: 170°, V: 170° (at contrast ratio 1:5) Response Time: approx.30 ms Dot Pitch 0.270 mm Horizontal Scan Analog: 24 - 100 kHz (Automatic) Frequency Digital: 31 - 100 kHz Analog: 49 - 86 Hz (Automatic) Vertical Scan (1600 x 1200: 49 - 76 Hz) Frequency Digital: 59 Hz - 61Hz, (VGA Text : 69 - 71 Hz) Resolution 1600 dots x 1200 lines Dot Clock (Max.) Analog: 202.
USB standard USB ports USB Specification Revision 2.
Dimensions Unit mm (inches) Pin Assignment DVI-I Connector Signal Pin No. Signal 1 TMDS Data 2- 11 TMDS Data 1/3 Shield 21 NC 2 TMDS Data 2+ 12 NC 22 TMDS Clock Shield NC 23 TMDS Clock+ 24 TMDS Clock- C1 Analog Red Pin No. Signal 4 TMDS Data 2/4 Shield NC* 5 NC 3 6 7 8 Pin No.
Analog Ground TMDS C5 (analog R, G, & B 9 TMDS Data1- 19 Data0/5 Shield return) 10 TMDS Data1+ 20 NC (*NC: No Connection) USB Ports No.
Afterimage The Afterimage is particular to LCD monitors when the monitor screen is left on for a long period without use. The "Afterimage" can be removed gradually by changing the displayed image. Clock With the analog input signal display, the analog signal is converted to a digital signal by the LCD circuitry. To convert the signal correctly, the LCD monitor needs to produce the same number clock pulse as the dot clock of the graphics system.
DVI (Digital Visual Interface) A digital flat panel interface. DVI can transmit digital data from the PC directly without loss with the signal transition method "TMDS". There are two kinds of DVI connectors. One is DVI-D connector for digital signal input only. The other is DVI-I connector for both digital and analog signal inputs. DVI DMPM (DVI Digital Monitor Power Management) The Power management system for the digital interface.
Phase The phase adjustment decides the sampling timing point for converting the analog input signal to a digital signal. Adjusting the phase after the clock adjustment will produce a clear screen. Range Adjustment The Range Adjustment controls the level of output signal range to display the whole color gradation. Resolution The LCD panel consists of a fixed number of pixel elements which are illuminated to form the screen image.
VESA DPMS (Video Electronics Standards Association - Display Power Management Signaling) The acronym VESA stands for "Video Electronics Standards Association", and DPMS stands for "Display Power Management Signaling". DPMS is a communication standard that PCs and graphics boards use to implement power savings on the monitor side.
Analog input Analog Eingang Analog numerique Preset Timing Chart Einstellung des Zeitdiagramms Diagramme des temps prédéfinis Based on the signal diagram shown below factory presets have been registered in the monitor's microprocessor. Der integrierte Mikroprozessor des Monitors unterstützt werkseitige Standardeinstellungen (siehe hierzu die nachfolgenden Diagramme). Signaux ont été enregistrés en usine dans le microprocesseur du moniteur, conformément au diagramme de synchronisation ci-dessous.
VESA VESA 800×600 800×600 VESA VESA 800×600 800×600 VESA VESA 800×600 800×600 VESA VESA 800×600 800×600 VESA VESA 1024×768 1024×768 VESA VESA 1024×768 1024×768 VESA VESA 1024×768 1024×768 VESA VESA 1024×768 1024×768 VESA VESA 1152×864 1152×864 VESA VESA 1280×960 1280×960* VESA VESA 1280×1024 1280×1024* VESA VESA 1280×1024 1280×1024* VESA VESA 1280×1024 1280×1024* VESA VESA 1600×1200 1600×1200* VESA 1600×1200 VESA 1600×1200 VESA 1600×1200 Portrait Display Portrait Display 1200×1600* 1200×1600 *contracted Di
The monitor supports the following resolutions only. Der Monitor reklamiert nur die nachforgent aufgeführten Auflösungen. Le moniteur ne peut utiliser que les résolutions suivantes. Mode Landscape Portrait VGA VGA 640×480 640×480 VGA TEXT VGA TEXT 720×400 720×400 VESA VESA 800×600 800×600 VESA VESA 1600×1200 1600×1200* Portrait Display Portrait Display 1200×1600* 1200×1600 *contracted Dot Clock MHz Sync Polarity H V Frequencies fH: kHz fV: Hz 25.2 MHz Nega Nega 31.5 60.0 28.3 MHz Nega Posi 31.
[Applicable to gray cabinet.] Congratulations! The display you have just purchased carries the TCO'03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the Impact on our natural environment.
❍ heavy metals such as cadium, mercury and lead. The requirements includes in this label have been developed by TCO Development in co-operation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more userfriendly direction. Our labeling system with displays in 1992 and is now requested by users and IT-manufacturers all over the world. For more information, please visit www.
[Applicable to black cabinet.] Congratulations! You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a product developed for professional use.
have an environmental policy which must be adhered to in each country where the company implements its operational policy. The energy requirements include a demand that the computer and/or display, after a certain period of inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to reactivate the computer shall be reasonable for the user.
Cadmium** Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99 requirement states that batteries, the colour-generating layers of display screens and the electrical or electronics components must not contain any cadmium. Mercury** Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic in high doses.
* Bio-accumulative is defined as substances which accumulate within living organisms. ** Lead, Cadmium and Mercury are haevy metals which are Bio-accumulative.
Hinweis zur Ergonomie Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1-ITB 2000 mit dem Videosignal, 1600 Punkte X 1200 Zeilen, RGB digital, 0,7 Vp-p und mindestens 75,0 Hz Bildwiederholfrequenz, non interlaced. Weiterhin wird aus ergonomischen Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast.) „Maschinenlärminformations-Verordnung 3.
Återvinningsinformation för kunder i EU: All information om återvinning finns på följande webbsidor: http://www.swico.ch http://www.eizo.de http://www.eizo.se Recycling Information for customers in USA: All recycling information is placed in the Eizo Nanao Technologies, Inc.'s website. http://www.eizo.com Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen.
e) f) g) h) Der Standfuß muß die Möglichkeit zur Drehung des Bildschirmgerätes besitzen (max. ± 180°). Der maximale Kraftaufwand dafür muß weniger als 100 N betragen. Der Standfuß muß in der Stellung verharren, in die er manuell bewegt wurde. Der Glanzgrad des Standfusses muß weniger als 20 Glanzeinheiten betragen (seidenmatt). Der Standfuß mit Bildschirmgerät muß bei einer Neigung von bis zu 10° aus der normalen aufrechten Position kippsicher sein.