E
CONTENTS PRECAUTIONS __________________________ 4 INTRODUCTION ________________________ 10 About this Manual .................................................. 10 Package Contents ................................................. 10 Controls & Connectors .......................................... 12 1 INSTALLATION ______________________ 16 1-1 Connecting up ................................................. 16 PC Settings ......................................................................
MAKING USE OF USB (Desktop Stand Type Only) ______________ 60 4 TROUBLESHOOTING _________________ 63 4-1 Troubleshooting ............................................... 63 5 CLEANING __________________________ 67 6 SPECIFICATIONS ____________________ 68 APPENDIX _____________________________ i Pin Assignment .........................................................ii Preset Timing Chart ................................................. iii Dimensions .....................................................
PRECAUTIONS IMPORTANT! * The manufacturer is not responsible for damage or malfunction caused by improper connection. The power cord should be connected directly to a standard wall power outlet. Location of the caution statements on the back panel. Risk of electric shock. Do not open. The equipment must be connected to a grounded main outlet. Risque de choc electrique. Ne pas ouvrir. Jordet stikkontakt skal benyttes nár apparatet tilkobles datanett. Gefahr des elektrischen schlages.
This manual uses the safety symbols below. They denote critical information. Please read them carefully. Indicates a prohibited action. Indicates to ground for safety. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage.
• Do not touch a damaged LCD panel directly with bare hands. Use protective gloves whenever handling a damaged panel. The liquid crystal which leaks from the panel is poisonous if it enters the eyes or mouth. If any part of the skin or body comes in direct contact with the panel, please wash thoroughly. If some physical symptoms result, please consult your doctor. • Take care in disposing of the LCD monitor. The backlight of the LCD monitor contains mercury.
• Keep the plastic packing bags away from children and infants. Plastic bags can be dangerous. To avoid danger of suffocation, keep the bag away from babies and children. • Keep power terminal covers for the optional peripheral unit away from children and infants. Children and infants may accidentally swallow the covers and choke. If swallowed, consult a doctor immediately. • Place the LCD monitor on a strong, stable surface (desktop stand type only).
PRECAUTIONS
• Do not use the power unit hanging in midair. Place it on a solid, flat surface (free mount type only). Do not drop the power unit. Hanging the power unit in midair may result in fire or electric shock. • Do not use the LCD monitor outdoors or inside a car. This LCD monitor has been made specifically for indoor use as a desktop monitor. Using it anywhere else may result in fire, electrical shock, or other damage. • Do not block the ventilation slots on the cabinet.
INTRODUCTION About This Manual This manual explains the precautions, features, specifications, and operation of your EIZO LCD monitor. For convenience, a “ScreenManager Quick Reference” guide has been included which shows how to implement basic adjustments with the ScreenManager utility. • This manual applies to the EIZO monitor types: The desktop stand type and the free mount type. Please note that there are some points which vary according to the type.
Package Contents E (Free Mount Type): Signal Cable (MD-C91) LCD Monitor Bracket Power Unit • If any of the above-listed items are missing or damaged, please contact your local dealer for assistance. • We recommend that you retain the original packing materials in case of future need.
Controls & Connectors (Desktop Stand Type) Front Viewing Angles Horizontal: 140° Vertical: 120° (4) (5) (6) (7) (1) (2) (3) (8) (1) Power Terminal Covers for the Optional Peripheral (2)Input Signal Selection Button Selects one of two D-Sub connectors as the active input. This feature is only used when two computers are connected to the LCD monitor. (3) Auto Adjustment Button Automatically centers the displayed image.
Rear E (1) (2) (3) (4) (5) (6) (8) (7) (1)Connector Cover Remove the connector cover of the LCD monitor to connect the signal cables. (2)Rear Cover Remove the rear cover of the LCD monitor to connect the signal cables. (3)D-Sub Connector Holder Used to prevent the D-Sub signal cables from becoming loose or disconnected. (4)2 x D-Sub mini 15 pin Input Connectors (Input Signal 1 and 2) (5)Maintenance Port Service use only.
Controls & Connectors (Free Mount Type) Front Viewing Angles Horizontal: 140° Vertical: 120° (6) (7) (1)(2)(3)(4) (5) (1) Power terminal covers for the optional peripheral (2) Input Signal Selection Button Selects one of two D-Sub connectors as the active input. This feature is only used when two computers are connected to the LCD monitor. (3) Auto Adjustment Button Automatically centers the displayed image.
Rear E (1) (2) (3) (4) (5) (6) (7) (1) D-Sub Connector Holder Used to prevent the D-Sub signal cables from becoming loose or disconnected. (2) 2 x D-Sub mini 15 pin Input Connectors (Input Signal 1 and 2) (8) (3) DC IN Connects to the enclosed power unit. (4) Maintenance Port Service use only. (5) Security Lock Allows for connection of a security cable. This lock supports the Kensington’s MicroSaver security system. For further information, please consult below.
1 INSTALLATION 1-1Connecting up Please read the appropriate pages for the LCD connection. Desktop Stand Type : Free Mount Type: From Page 17 to 21 From Page 22 to 26 PC Settings Before connecting your PC to the L360 LCD monitor, change the display screen settings (resolution and frequency) in accordance with those below. fH: 30 kHz-61 kHz fV: 50 Hz-85 Hz • The maximum resolution of this LCD monitor is 1024 x 768 at a maximum fV of 75 Hz.
Connecting the Cables (Desktop Stand Type) (1)Be sure that the power switches of both the PC and the LCD monitor are OFF. (2)Remove the D-Sub connector holder. a) Hand-loosen the screws at the center of the holder. b) Pull the holder away while squeezing both sides of the holder. (3)Plug the signal cable (which is marked “LCD”) into the D-Sub connector (Signal 1) at the rear of the monitor. Please ensure that the arrow mark on the casing of the connector is visible when connecting. See note.
Standard PC graphics board Standard PC graphics board Macintosh Please connect the optional Macintosh adapter to the PC before attaching the signal cable. Macintosh (6)Replacing the connector cover and the rear cover. a) To close easily, the LCD monitor should be tilted forward as shown in the diagram. • When tilting the panel, take care not to catch your fingers between the rear panel and the stand. b) Attach the connector cover to the rear panel of the LCD.
c) Insert the rear cover into the inlets at the bottom of the stand. E Inlets Rear cover d)Close the rear cover while pushing the push buttons on the top. buttons (7) Plug the power cord into the power connector in the rear of the LCD monitor. Plug the other end into a power outlet. (8) Turn on the monitor’s main power and then switch on the PC power. (9) This completes the installation. Turn off the main power when you finish using it.
(1)To open easily the LCD monitor should be tilted forward as shown in the diagram. (2) Pull the rear cover clear while pushing the push buttons on the top. (3) Pull down and remove the connector cover.
Connecting two PCs to the Monitor E (Example) The EIZO L360 has two video input signal connectors (2 x D-sub mini 15 pin). The priority switch system allows the user to assign priority to either input signal.
Connecting the Cables (Free Mount Type) (1)Be sure that the power switches of both the PC and the power unit are OFF. Lay the LCD monitor as shown below. Free Mount Type LCD Monitor (2)Plug the power unit into the power connector in the rear of the LCD monitor. (3)Remove the D-Sub connector holder. a) Hand-loosen the screws at the center of the holder. b) Pull the holder away while squeezing the both sides of the holder.
(4)Plug the signal cable (which is marked “LCD”) into the D-Sub connector (Signal 1) at the rear of the monitor. Please ensure that the arrow mark on the casing of the connector is visible when connecting. See note. When connecting the signal cable, check that the shape of the cable connector matches the shape on the LCD monitor. (5)Replace the D-Sub connector holder and hand-tighten the screw. (6)a)Place the bracket on the rear of the LCD monitor. Fix the bracket to the rear of the LCD monitor securely.
• In case of using this LCD monitor with an arm-stand in an office workspace, the arm-stand shall be chosen and used carefully: - Use only an approved arm-stand (e.g. GS). - The arm-stand shall have sufficient stability (mechanical firmness) due to the load with this monitor included the optional parts which we recommend. (suitable for at least 8.0 kg) -The arm-stand shall remain in that position where it is manually moved.
Macintosh E Please connect the optional Macintosh adapter to the PC before attaching the signal cable. Macintosh (8) Plug the power cord into the power unit, and plug the other into a power outlet. • In case of setting the plural free mount type monitors, please be sure to observe the followings. *Do not pile the power units. *Set the power units at minimum intervals of 20 mm. Refer to the diagram below. 20 mm OK (9) Turn on the monitor’s main power and then switch on the PC power.
Connecting two PCs to the Monitor (Example) Macintosh Adapter DSCR-153 (optional) Apple Macintosh PC compatible MD-C91 The EIZO L360 has two video input signal connectors (2 x D-sub mini 15 pin). The priority switch system allows the user to assign priority to either input signal. • Use the specified optional cable: MD-C91 only or with Macintosh adapter when connecting the second computer to the monitor. • Contact EIZO dealers for information about optional cables.
2 USING THE SCREENMANAGER 2-1 How to use the ScreenManager E About ScreenManager As shown on the display, the ScreenManager is used to adjust the LCD monitor. Adjustments are made using the Enter and Control buttons (up, down, right and left) located on the front panel. Enter button Control buttons ScreenManager Menus ScreenManager consists of a main menu and six sub menus: “Screen”, “Color”, “PowerManager”, “Others”, “Information” and “Language.” Animated icons on each menu allows for easy adjustment.
Sub menus Icon 28 2 Menus Functions Reference Screen menu Each display mode can have various screen parameters adjusted to enhance viewing. There are: * Clock * Phase * Position * Resolution * Contrast / Brightness Ch.2-2 3 Ch. (pg. 27) (pg.32) 28 Color menu Use this menu to select color mode: 1, 2 or 3. By adjusting the red, green, and blue color tones for each mode, custom colors can be defined. Ch.2-3 4 Ch. (pg. 36) (pg.
Icon Menus Information menu Language menu Functions Use this feature to review the current ScreenManager settings. The menu contains four pages. Pushing the Enter button selects each page in order. The information displayed for each page is as follows: * Page 1: "Screen" “Screen” menu settings * Page 2: "Color" “Color” adjustment settings * Page 3: "PowerManager" “PowerManager” settings settings * Page 4: "Others" “Others” menu settings Use this menu to select the ScreenManager language.
How to use the ScreenManager Entering the ScreenManager Push the Enter button once to display the main menu of the ScreenManager. Enter the Settings (1) To enter any sub menu icon, highlight the desired icon by using the Control buttons (up, down, right and left) and push the Enter button. The sub menu appears. (2) Use the Control buttons to select the desired setting icon and push the Enter button. (3) The setting menu appears. Use the Control buttons to make all required adjustments.
E • Return & Exit icons To return to the main menu from the sub menu or exit the ScreenManager, select this icon and push the Enter button. Shortcut keys Brightness and contrast can be adjusted directly without any need to enter the ScreenManager. Press the Control buttons to adjust the settings and then the Enter button to save all changes. See the diagram below for adjustment directions. The brightness and contrast functions are also available in the ScreenManager “Screen” menu.
2-2 Screen Adjustment About Screen Adjustments Entering the ScreenMananger, select the “Screen” icon and push the Enter button to show the “Screen” menu. “Screen” adjustments for the LCD monitor should be used in suppressing screen flickering and also for adjusting the screen to its proper position. There is only one correct position for each display mode. It is also recommended to use the ScreenManager function when first installing the display or whenever changing the system.
E 2 USING THE SCREENMANAGER 33
Procedure Please adjust the screen using the following procedure. (1) Having read the “readme.txt” file, install and run the “Screen Adjustment Program” in the utility disk. Step by step adjustment is provided by the wizard guide. Follow the wizard or the procedures (2) to (8) below. • If the user's operation system has no utility disk (e.g. OS/2), we recommend setting the desktop pattern to that as shown in the diagram below.
(3) Entering the ScreenManager “Screen” menu. E (4) “Clock” Adjustment a) Select the “Clock” icon and push the Enter button to enter the “Clock” menu. b) If vertical bars of distortion on the screen appear, these can be eliminated by adjusting the right and left buttons. Then look at the illustration and the explanation below. i) If the screen is free from any bars of distortion, proceed to step (6) “Position” adjustment.
(5) “Phase” Adjustment a) Select the “Phase” icon and push the Enter button to show the “Phase” menu.” b) If horizontal bars appear, these can be eliminated by adjusting the right and left buttons. c) After finishing the adjustment, push the Enter button to memorize the settings and return to the “Screen” menu. • “Phase” adjustments should be done after adjusting the “Clock”. • Horizontal bars may not completely disappear from the screen depending on the PC.
(7) Confirm the “Resolution”. a) Select the “Resolution” icon and push the Enter button to enter the “Resolution” menu. b) Confirm if the resolution now being displayed is the same as the input resolution. If it is not, adjust the vertical resolution using the up and down buttons and adjust the horizontal resolution using the right and left buttons. c) After finishing the adjustment, push the Enter button to memorize the settings and return to the “Screen” menu.
(9) Exit the ScreenManager a) To return to the main menu, select the “Return” icon or push the down button twice, followed by the Enter button. b) To exit the ScreenManager, select the “Exit” icon and push the Enter button. Double clicking the Enter button at any time also exit the ScreenManager menu. This is the end of the Screen adjustment procedure. For more detailed information about each feature, refer to the next chapter, “Screen Adjustment Features”.
2. Phase Adjustment E This feature eliminates the horizontal bars of distortion. The phase adjustment decides the sampling point for converting the analog input signal to a digital signal. Adjusting the “Phase” after the “Clock” adjustment will produce a clear screen. 3. Position Adjustment This feature controls the screen position. The number of screen pixels and the screen position are fixed for the LCD monitor. Only one position is right and the displayed image should be adjusted to this position. 4.
14 preset timings have been committed to memory. In addition to these settings, a screen can be displayed correctly using the “Clock”, “Phase” and “Position” adjustments if the input signal is one of the following resolutions (640 x 480, 720 x 400, 800 x 600, 832 x 624, 1024 x 768). If the signal is very different from one of the preset resolutions, then the screen can be adjusted using the “Resolution” Adjustment.
E * In the case of the percentage color flickering between orange and white, please note that this is not an error but actually the most optimum adjustment point. * The brightness of the entire screen is controlled by changing the “Brightness” controls. No contrast adjustment is required except when the graphics board or the resolution is changed from the previous one. 6. Brightness Adjustment This feature controls the brightness of the screen.
2-3 Color Adjustment About Color Adjustments Entering the ScreenManager, select the “Color” icon and push the enter button to show the “Color” menu. The ScreenManager “Color” menu provides 3 color setting modes; 1, 2, and 3. You can also adjust the color settings for each mode and store them for future use. • Allow the monitor to warm-up for at least 20 minutes before making an adjustment. Color Mode There are 3 color modes.
Custom Color Adjustments E By adjusting the red, green and blue color tones for each mode, custom colors can be defined. Please use this function when high precision color adjustment is required. Procedure • Before you attempt to change the colors, always start with the color settings set to the default setting by using the “Reset” icon in each color mode. (1) Select the “Color Mode” icon from the “Color” menu and push the Enter button. (2) Select option 1, 2 or 3 and push the Enter button.
• After making the color settings, re-adjust the contrast to get the best definition and color intensity for the displayed image. • “Reset” You can recall the default color gain setting for the current color mode (1, 2, 3) using the “Reset” icon. • The values shown in percentages represent the current level within the specific adjustment only. They are available only as a reference tool. (To create a uniform white or black screen, the percentages for each will probably not be the same.
2-4 Power-save Setup E About PowerManager Entering the ScreenManager, select the “PowerManager” icon and push the Enter button to show the “PowerManager” menu. The PowerManager feature automatically reduces the monitor’s power consumption during idle periods in accordance with the PCs ScreenSaver software. Even if the monitor is in a power saving mode, it will return to a normal display immediately when the mouse or keyboard is operated.
Set-up Procedure Set the monitor’s power saving environment to match the PC’s ScreenSaver software. • For the PC setup, please refer to the user’s manuals of the PC and the graphics board. There are two power saving settings for the monitor. “VESA DPMS” system works with the VESA DPMS signal. “EIZO MPMS” system works with a screen saver software and Energy Saver for Macintosh which blanks the screen (totally black screen). Set the monitor to match the PC’s power saving software, as follows.
VESA DPMS System E 1) First, make the appropriate settings for the PC. (See note, page 46.) 2) Then select “VESA DPMS”. 3) Set the delay period, which is the interval that the monitor will wait after receiving a power saving signal from the PC, before entering into a power saving mode. VESA DPMS Power Saving Method VESA DPMS utilizes four signals: ON, STANDBY, SUSPEND, and OFF. The monitor detects these signals from the graphics board and executes power saving accordingly, as illustrated below.
EIZO MPMS System 1) First make the appropriate ScreenSaver settings (Macintosh/Energy Saver) for the PC. 2) Then select “EIZO MPMS”. 3) Set the delay time. This is the interval between the time that the ScreenSaver (Macintosh/EnergySaver) blanks the screen and the time that the monitor enters power saving mode.
What is VESA DPMS? The acronym VESA stands for “Video Electronics Standards Association,” and DPMS stands for “Display Power Management Signaling.” DPMS is a communication standard that PCs and graphics boards use to implement power savings at the monitor side. What is EIZO MPMS? EIZO MPMS, "EIZO Monitor PowerManager Signaling", also enables to execute power saving at the monitor side.
2-5 Other Settings About Other Settings Entering the ScreenManager, select the “Others” icon and push the Enter button to show the “Others” menu. All of the icons shown in the ScreenManager “Others” menu are described below.
What is the “Screen Size” setup function? The LCD panel consists of a fixed number of pixel elements which are illuminated to form the screen image. The EIZO L360 display panel consists of the following pixel elements: 1024 horizontal pixels and 768 vertical pixels. At the resolution of 1024 x 768, all pixels are used and the image is displayed as a full screen. At the lower display modes of 800 x 600 or 640 x 480 the images are displayed in the center of the screen using a smaller portion of the pixels.
Color Enhancer This function is used for expanding the displayable colors from 262,144 to true color (16 million). Adjustment Procedure Please adjust the color enhancer using the following procedure: (1) Select the “Color Enhancer” icon and push the Enter button to show the “On / Off” select menu. (2)Select “On” and push the Enter button to select true color (16 million). (3)Select the “Return” icon and push the Enter button to return to the main menu of the ScreenManager.
Border Intensity E This function is used for changing the brightness of the black area surrounding the displayed image. Adjustment Procedure Please adjust the border intensity using the following procedure: (1)Select the “Border Intensity” icon and push the Enter button to display the adjustment menu. (2)Adjust the brightness of the border area using the right and left buttons. (3)Push the Enter button to return to the “Others” menu.
Input Priority This function is used to select which PC will have priority to control the monitor when utilizing two PCs. As you can see in the picture, there are three settings available: “Signal 1”, “Signal 2” or “Manual”. The default priority setting is “Signal 1”. The monitor constantly checks the input signals and switches automatically in accordance with the “Input Priority” settings (see chart below).
1 The Input Priority function does not automatically re-activate when the monitor has been in the power saving mode. 2 The Input selection button on the front panel can be used to select either Signal 1 or Signal 2 as the active input at any time. Procedure for Input Priority Selection Please set the Input priority using the following procedure: (1)Select the “Input priority” icon and push the Enter button to show the “Signal 1/Signal 2/ Manual” select menu.
Setup Procedure (1) Select the “Off Timer” icon and press the Enter button to display “Off Timer” select menu. (2) Select “Enable” and press the enter button. (3) Press the right/left key to adjust how long (1 to 23 hours) the monitor should be in the “On Period”. Then, press the enter button to return to the “others” menu. (4) Select the “Exit” icon and push the Enter button to exit the ScreenManager.
Beep Use this feature to set the beeper On or Off. If the beeper is On, the LCD monitor will generate beep signals as defined below. If the beeper is Off, the monitor will not beep. Short beep • ScreenManager item selected. • ScreenManager parameter adjusted to minimum or maximum limit. • Input signal selection button pressed. Long beep • Auto Adjustment button pressed. • ScreenManager data-save executed. Four short beeps • Monitor not connected correctly. • PC turned off.
Menu Position Use this function to adjust the position of the ScreenManager menu. Procedure for Menu Position Selection Please set the Menu Position using the following procedure: (1)Select the “Menu Position” icon and push the Enter button to display the adjustment menu. (2)Set the position using the right, left, up and down buttons. (3)Push the Enter button to return to the “Others” menu. (4)Select the “Return” icon and press “Enter’ to return to the main menu of the ScreenManager.
Procedure for Reset Selection E Please reset the default using the following procedure: (1)Select the “Reset” icon and push the Enter button to show the adjustment menu. (2)Select “Reset” using the up and down buttons. A confirmation message will appear. (3) Push the Enter button to proceed and return to the “Others” menu. (4) Select the “Return” icon and push the Enter button to return to the main menu of the ScreenManager. (5) Select the “Exit” icon and push the Enter button to exit the ScreenManager.
3 MAKING USE OF USB -For USB Compliant System Environments(Desktop Stand Type Only) Desktop Stand Type provides a hub which supports the USB (Universal Serial Bus) standard. When connecting to a USB compliant PC or another hub, the monitor functions as a hub to which the USB compliant peripherals can be connected. The USB standardized connectors enable the easy connection with these peripherals. • To utilize the USB hub function, the following system environment is required.
3) Select “Search for the best driver for your device (recommended).” and click “OK”. 4) Insert the Windows 98 CD-ROM. 5) Select “specify a location” and choose the driver where Windows 98 is installed (e.g., select c: if Windows 98 is in C drive), and click “Next”. 6) Confirm “Generic USB Hub” is selected in the wizard. Click “Next”. 7) Choose the driver where CD-ROM is installed (e.g., d:\win98), and click “OK” if the location of the driver is asked. 8) The “Generic USB Hub” is detected.
USB Specifications USB standard Rev. 1.0 complied self-powered hub Downstream power supply 500 mA for each (Max.) Communication speed 12 Mbps (full), 1.5 Mbps (low) USB ports Upstream port x 1 Downstream ports x 4 Troubleshooting Problems 1) • USB function cannot be setup. Points to check with possible solutions Check that the USB cable is correctly connected. Check that the PC and OS is compliant to the USB. (For the USB support of the system, consult the manufacturer of each system.
4 TROUBLESHOOTING 4-1 Troubleshooting This page presents problems that can be corrected by the user. If a problem persists even after applying the suggested remedies, contact an EIZO dealer. n No picture Problems Points to check with possible solutions 1) Indicator status: OFF Check that the power cord is securely connected. 2) Indicator status: GREEN Try pressing a key on the keyboard, or clicking the mouse. (The screen-saver software may be active.) Try pressing the power button.
• Whenever an error signal message appears, the signal frequency will be displayed in red. • Error messages will remain on the screen for 30 seconds, and then disappear. An error message may not appear at all if the signal frequency is extremely high or extremely low. n Imaging problems Problems Points to check with possible solutions 1) Display position is incorrect. Push the Auto adjustment button. See page 36.
Problems Points to check with possible solutions 4) Horizontal bars of distortion appear. Decrease the horizontal bars using the “Phase” icon in the ScreenManager “Screen” menu. See page 36, 39. 5) The screen is too bright or too dark. Adjust the contrast and brightness using the ScreenManager’s Screen menu. See page 37, 40. E (The backlight of the LCD monitor has a fixed life span. When the screen becomes dark or begins to flicker, please contact your dealer.) 6) after-images appear.
Problems 4) The Auto adjustment button does not work properly. Points to check with possible solutions The Auto adjustment function is intended for use on Macintosh and IBM compatibles PCs running Windows. It may not work properly if either of the following applies. - You are running an AT-compatible PC on MSDOS (not Windows). - The background color for the “wallpaper” or “desktop” pattern is set to black. Some signals from the graphics boards may not function properly.
5 CLEANING WARNING E • Keep liquids away from the monitor. Spillage into the cabinet may result in fire, electric shock, or equipment damage. If an object or liquid falls/spills into the cabinet, unplug the monitor immediately. Have the unit checked by a qualified service engineer before using it again. CAUTION • To ensure safety, always unplug the monitor before cleaning it. Cleaning the monitor while it is plugged into a power outlet may result in electric shock.
6 SPECIFICATIONS L360 (Desktop Stand Type) E Electrical Specifications LCD Panel 38 cm (15 inch), TFT color LCD panel 0.297 mm dot pitch, Anti-Glare Hard Coating Viewing Angle Horizontal: 140°, Vertical: 120° (at Contrast Ratio > 5) Scan Frequency(Horizontal): 30 kHz-61 kHz (Automatic) Scan Frequency (Vertical): 50 Hz-85 Hz (Automatic) (1024 x 768: up to 75 Hz) Max. Active Display Area 304.1 mm (H) x 228.1 mm (V) (11.9” (H) x 8.9” (V)) (Viewable Image Size: 380 mm (14.
L360 (Free Mount Type) E Electrical Specifications LCD Panel 38 cm (15 inch), TFT color LCD panel 0.297 mm dot pitch, Anti-Glare Hard Coating Viewing Angle Horizontal: 140°, Vertical: 120° (at Contrast Ratio > 5) Scan Frequency(Horizontal): 30 kHz-61 kHz (Automatic) Scan Frequency(Vertical): 50 Hz-85 Hz (Automatic) (1024 x 768: up to 75 Hz) Max. Active Display Area 304.1 mm (H) x 228.1 mm (V) (11.9” (H) x 8.9” (V)) (Viewable Image Size: 380 mm(14.7”)) Power Supply 100-120/220-240 VAC ± 10%, 50/60 Hz, 0.
APPENDIX Pin Assignment Pin-Belegung Affectation des Broches 2 x D-Sub mini 15 pin connectors Pin No. Signal Pin No. Signal 1 Red video 9 No pin 2 Green video 10 Ground 3 Blue video 11 (shorted) 4 Ground 12 Data 5 No pin 13 H. Sync 6 Red ground 14 V. Sync 7 Green ground 15 Clock 8 Blue ground Shell Ground USB ports (Desktop Stand Type Only) Upstream (Series B connector) ii APPENDIX Downstream (Series A connector) No.
Preset Timing Chart Timing-Übersichten Synchronisation des Signaux Based on the signal diagram shown below, 14 factory presets have been registered in the monitor's microprocessor. Der integrierte Mikroprozessor des Monitors unterstützt 14 werkseitige Standardeinstellungen (siehe hierzu die nachfolgenden Diagramme). 14 signaux ont été enregistrés en usine dans le microprocesseur du moniteur, conformément au diagramme de synchronisation ci-dessous.
Mode Dot Clock Frequencies H V A: Front Porch B: Sync Period H V H V µs/Dot ms/Line µs/Dot ms/Line VGA 640 x 480 25.175 MHz 31.468 kHz 59.941 Hz 0.636 / 16 0.318 / 10 3.813 / 96 0.054 / 2 VGA 720 x 400 28.322 MHz 31.468 kHz 70.087 Hz 0.636 / 18 0.381 / 12 3.813 / 108 0.064 / 2 VESA 640 x 480 31.5 MHz 37.86 kHz 72.81 Hz 0.508 / 16 0.026 / 1 1.270 / 40 0.079 / 3 VESA 640 x 480 31.5 MHz 37.50 kHz 75.00 Hz 0.508 / 16 0.027 / 1 2.032 / 64 0.080 / 3 VESA 640 x 480 36.
C: Back Porch D: Blanking Period E:Display Period F:Total Cycle H V H V H V H V µs/Dot ms/Line µs/Dot ms/Line µs/Dot ms/Line µs/Dot ms/Line 1.907 / 48 1.048 / 33 6.356 / 156 1.430 / 45 640 25.442 / 480 15.254 / 800 31.778 / 525 16.683 / 1.907 / 54 1.111 / 35 6356 / 180 1.556 / 49 25.422 / 720 12.712 / 400 31.778 / 900 14.267 / 449 3.810 / 120 0.528 / 20 5.587 / 176 0.634 / 24 20.317 / 640 12.678 / 480 26.413 / 832 13.735 / 520 3.810 / 120 0.427 / 16 6.
Dimensions Abmessungen Dimensions Desktop Stand Type LCD Monitor mm (inches) 397 (15.6) 37.5 (1.4 ) 3 17 (12.4 ) 45.5 (1.7) 15.6 (397 ) 18° 3° 49.5 (1.9) 90 (3.5 ) 4 5.5 (1.7 ) 10.5 (0.4) 15 0.8 (5.9) 4 0. 4 (1.5) 9.3 (283 ) 179 (6. 9) FRONT VIEW VORDERANSICHT VUE DE FACE SIDE VIEW SEITENANSICHT VUE DE COTE 53.6 (2.1 ) 82 (3.2) 176 (6.9 ) 1 .4 (38) 40.4 (1.
Free Mount Type LCD Monitor mm (inches) 397 (15.6) 37.5 (1.4) 3 17 (12.4 ) A 45.5 (1.7) 4 9.5 (1.9) FRONT VIEW VORDERANSICHT VUE DE FACE 92 (3.2) 82 (3.2) SIDE VIEW SEITENANSICHT VUE DE COTE 1 .
Except for Black-Cabinet L360 Congratulations! You have just purchased a TCO’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Except for Black-Cabinet L360 Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs.
For Europe, etc. (220-240 Vac) Only CE Marking Declaration of Conformity Kind of equipment: Type-designation: Monitor L360 (Model No.
For Europe, etc. (220-240 Vac) Only CE Marking Declaration of Conformity Kind of equipment: Type-designation: Monitor L360 (Model No.
For U.S.A, Canada, etc. (rated 100-120 Vac) Only FCC Declaration of conformity We, the Responsible Party EIZO Nanao Technologies Inc. 5710 Warland Drive, Cypress, CA 90630 Phone: (562) 431-5011 declare that the product Trade name: EIZO Model: FlexScan L360 (Desktop Stand Type) Model No: FA-1562 Model: FlexScan L360 (Free Mount Type) Model No: FA-1563 is in conformity with Part 15 of the FCC Rules.
