User’s Manual Color LCD Monitor
English SAFETY SYMBOLS This manual uses the safety symbols below. They denote critical information. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety. Copyright© 2001 by EIZO NANAO CORPORATION. All rights reserved.
English TABLE OF CONTENTS PRECAUTIONS ...................................................................................... 4 1. INTRODUCTION ..................................................................................... 9 1-1. Features ........................................................................................................9 1-2. Package Contents..........................................................................................9 1-3. Controls & Connectors ....................
English PRECAUTIONS IMPORTANT! • This product has been adjusted specifically for use in the region to which it was originally shipped. If operated outside the region to which it was originally shipped, the product may not perform as stated in the specifications. • To ensure personal safety and proper maintenance, please read this section and the caution statements on the unit (refer to the figure below).
English WARNING Keep small objects or liquids away from the unit. Small objects accidentally falling through the ventilation slots into the cabinet or spillage into the cabinet may result in fire, electric shock, or equipment damage. If an object or liquid falls/spills into the cabinet, unplug the unit immediately. Have the unit checked by a qualified service engineer before using it again. Place the unit on a strong, stable surface.
English WARNING The equipment must be connected to a grounded main outlet. Not doing so may cause in fire or electric shock. Use the correct voltage. * Do not overload your power circuit, as this may result in fire or electric shock. * The unit is designed for use with a specific voltage only. Connection to another voltage than specified in this User’s Manual may cause fire, electric shock, or other damage. * Do not overload your power circuit, as this may result in fire or electric shock.
English CAUTION Handle with care when carrying the unit. Disconnect the power cord and cables when moving the unit. Moving the unit with the cord attached is dangerous. It may result in injury or equipment damage. When handling the unit, grip the bottom of the unit firmly with both hands ensuring the panel faces outward before lifting. Dropping the unit may result in injury or equipment damage. OK Do not block the ventilation slots on the cabinet.
English LCD Panel The screen may have defective pixels. These pixels may appear as slightly light or dark area on the screen. This is due to the characteristics of the panel itself, and not the product. The backlight of the LCD panel has a fixed life span. When the screen becomes dark or begins to flicker, please contact your dealer. Do not press on the panel or edge of the frame strongly, as this will result in damage to the screen.
English 1. INTRODUCTION Thank you very much for choosing an EIZO Color Monitor. 1-1. Features • Dual inputs compliant • DVI (p. 44) Digital input (TMDS (p. 45)) compliant • Horizontal scanning frequency: 31 - 61 kHz (Digital input: 31 - 49 kHz) Vertical scanning frequency: 50 - 85 Hz Vertical (1024 x 768 ~ 75 Hz) Vertical (Digital) of 60 Hz (VGA text: 70 Hz) Resolution: 1024 x 768 • Smoothing function incorporated for the adjustment of an enlarged image. (p.
English 1-3.
English Rear (11) (9) (10) Bottom (12) (9) (10) (11) (12) (13) (14) (15) *2 *3 (13)(14) (15) Stand with cable holder (Detachable)*2 Power Terminal Covers for the Optional peripheral Security Lock Slot*3 DVI-I Input Connector x 2 (SIGNAL 1, SIGNAL 2) USB Port (2 Downstream) USB Port (1 Upstream) Power Connector The LCD monitor can be used with an optional arm stand by removing the stand. (see page 34) Allows for connection of a security cable.
English 2. CABLE CONNECTION 2-1. Before connecting Before connecting your monitor to the PC, change the display screen settings (resolution p. 45) and frequency) in accordance with the charts below. NOTE • When your computer and display support VESA DDC, the suitable resolution and the refresh rate are set by just plugging your display into the computer without any manual settings.
English 2-2. Connecting the signal cable NOTE • Be sure that the power switches of both the PC and the monitor are OFF. 1. Plug the signal cable into the connector at the rear of the monitor and the other end of the cable into the video connector on the PC. After connecting, secure the connection with the screw-in fasteners.
English 3. Lead the power cord and signal cable into the cable holder at rear of the monitor. Cable Holder 4. Plug the other end of the power cord into a power outlet. WARNING Use the enclosed power cord and connect to the standard power outlet of your country. Be sure to remain within the rated voltage of the power cord. Not doing so may cause in fire or electric shock. The equipment must be connected to a grounded main outlet. Not doing so may cause in fire or electric shock.
English 2-3. Connecting two PCs to the monitor Two PCs can be connected to the monitor through the Signal 1 and the Signal 2 on the back of the monitor. Connecting Examples Signal 1 Signal 2 PC 1 PC 2 (Ex.1) Analog D-Sub mini 15 pin Signal Cable (FD-C16 enclosed) Signal Cable (FD-C04 enclosed) DVI Digital (Ex.2) Analog D-Sub mini 15 pin Signal Cable (FD-C16 enclosed) Signal Cable (FD-C16 optional) D-Sub mini 15 pin Analog (Ex.
English Selecting the active input The Input signal selection button on the front panel can be used to select either Signal 1 or Signal 2 as the active input at any time. Every time the button is pressed, the input changes. When switching the signal, the kind of the input signal (Signal1 or 2/Analog or Digital) is displayed for a few seconds on the right top corner of the screen.
English 3. ScreenManager 3-1. How to use the ScreenManager Control Buttons Left, Down, Up, Right SIGNAL AUTO 1-2 Auto Adjustment button 1. ENTER Enter button Entering the ScreenManager Push the Enter button once to display the main menu of the ScreenManager. [ Main Menu ] 2. Making Adjustments and Settings (1) Select the desired sub menu icon using the Control buttons and push the Enter button. The sub menu appears.
English 3-2. ScreenManager Adjustments and Settings. The following table shows all the ScreenManager’s adjustment and setting menus. “*” indicates adjustments of analog input only and “**” indicates digital input only. Main menu Screen Sub menu Reference Clock * Phase * 4-1. Screen Adjustment (p.21) Position Resolution Smoothing Contrast/Brightness ColorManagement Signal Filter * Range Adjustment * 4-3. Color Adjustment (p.
English 3-3. Useful Functions Adjustment Lock Use the “Adjustment Lock” function to prevent any accidental changes. Locked function • Auto adjustment button adjustments and settings in the ScreenManager. • Auto Adjustment Button Unlocked function • Adjustment of contrast and brightness by the control buttons. • Input signal selection button • To lock Switch off the monitor’s power by the power button on the front panel. Press on the Auto adjustment button while switching on the monitor’s power.
English EIZO Logo appearing function When switching on the power button on the front panel, the EIZO logo is displyed for a while. If you desire to display or undisplay this logo, use this function. (Default is logo appearing.) • To undisplay Switch off the monitor’s power by the power switch on the front panel, then hold down the Enter button once again and turn the power back on.
English 4. ADJUSTMENT 4-1. Screen Adjustment NOTE • Allow the LCD monitor to stabilize for at least 20 minutes before making image adjustments. When connecting the DVI-I cable for digital input, see page 25. Analog Input Screen adjustments for the LCD monitor should be used in suppressing screen flickering and also for adjusting the screen to its proper position. There is only one correct position for each display mode.
English 3. Adjust by using menu in the ScreenManager. (1) Vertical bars appear on the screen → Use the (p.44) adjustment. Select the “Clock” and eliminate the vertical bars by using the right and left of the control buttons. Do not continuously press the control buttons, as the adjustment value will change quickly and make it difficult to locate the most suitable adjustment point. If the horizontal flickering, blur or bars appear, proceed to “Phase” adjustment as follows.
English (3) The screen position is not incorrect. Use the adjustment. → The correct displayed position of the monitor is decided because the number and the position of the pixels are fixed. The adjustment moves the image to the correct position. Select and adjust the position of the upper left corner of the image by using the up, down, right and left buttons in order to align the screen.
English 4. Adjust the output signal range (Dynamic Range) of the signal. → Use the (p.45) of menu. This controls the level of output signal range to display the whole color gradation (256 colors). [Procedure 1] Push the Auto adjustment button on the front panel while displaying the menu to automatically adjust the range. The screen blanks for a moment, and adjusts the color range to display the whole color gradation of the current output signal.
English Digital input The monitor displays the digital input image correctly based on its pre-setting data. However, if the image position is not correct or larger than the actual image screen, please adjust the following adjustment items using the “Screen” menu of the ScreenManager. 1. The screen position is incorrect. Use the adjustment. → See page 23. 2. Screen image is smaller or larger than the actual screen images. → Use the adjustment. See page 23. 3.
English 4-2. Displaying a low resolutions The lower resolutions are enlarged to full screen automatically. Using the function in the menu enables to change the screen size. 1. Enlarge the screen size when displaying a low resolution. → Select the . Select the in the others menu and select the screen size by using the up and down buttons. Menu Function Full Displays the picture on the screen in full, irrespective of the picture’s resolution.
English 3. Set the brightness of the black area surrounding the displayed image. → Set the . In the mode or mode, the outer area (border) is usually black. Select in the menu and adjust by using the right and left buttons. Border 4.
English 4-3. Color Adjustment The menu in the ScreenManager enables to change the color of the screen. By using the , the adjustment mode can be selected from (to adjust the color settings according to your preference) and mode. In the analog input, perform the “Range Adjustment” (p.24) before making the color adjustments. NOTE • Allow the LCD monitor to stabilize for at least 20 minutes before making image adjustments.
English To change the flesh color, etc. → Use the adjustment. The can be selected from –20 to 20. NOTE • The adjustment may cause undisplayable color tone. To change each color (red, green and blue) → Use the (p.44) adjustment. By adjusting the red, green and blue color tones for each mode, custom colors can be defined. The 100 % indicates unadjusted condition. Display a white or gray background image and adjust the .
English 4-4. Power-save Setup The menu in the ScreenManager enables to set the power-save setup. NOTE • Do your part to conserve energy, turn off the monitor when you are finished using it. Disconnecting the monitor from the power supply is recommended to save energy completely. • Even if the monitor is in a power saving mode, USB compliant devices function when they are connected to the monitor’s USB (both the upstream and the downstream ports).
English To set the power save with ScreenSaver (EIZO MPMS) software. [Procedure] (1) Set the PC’s appropriate ScreenSaver settings or blank the screen (totally black screen). (2) Select in the menu. [Power saving system] PC Operation Blank the screen (ScreenSaver or Macintosh Energy Saver) Monitor LED Operation Green Power saving Yellow Operate the mouse or keyboard to return to a normal screen. NOTE • EIZO MPMS should be used with Macintosh “EnergySaver”.
English 5. MAKING USE OF USB (Universal Serial Bus) This monitor provides a hub which supports the USB standard. When connecting to a USB compliant PC or another hub, the monitor functions as a hub to which the USB compliant peripherals can be easily connected. Required system environment • PC equipped with USB ports or another USB hub connected to the USB compliant PC • Windows 98/2000 // Mac OS 8.5.
English After connecting the USB cable, the USB function can be set up automatically. 3. After setting up, the monitor’s USB hub is available for connecting USB compliant peripherals to the downstream ports of the monitor. Connecting Examples Monitor PC Mouse Keyboard Printer Downstream Downstream ports: Connect the cables from USB compliant peripherals such as a mouse, keyboard, etc. Printer Keyboard 5.
English 6. ATTACHING AN ARM STAND The LCD monitor can be used with an arm stand by removing the tilt stand and attaching the arm stand to the LCD monitor. NOTE • Use an arm stand that satisfies the followings. - When using the LCD monitor with an arm stand, the arm stand must be VESA approved: *Use an arm stand with a 75 mm x 75 mm hole spacing on the arm mounting pad. *Weight: Use an arm stand that is able to support an object weighting 8.0 kg (17.6 lbs.).
English 4. Attach an arm stand to the LCD monitor securely. Arm-stand M4 Mounting Screws: M4 x 12 (mm) Zn/Fe 6.
English 7. TROUBLESHOOTING If a problem persists even after applying the suggested remedies, contact an EIZO dealer. • No picture problems → See No.1 ~ No.2 • Imaging problems → See No.3 ~ No.13 • Other problems → See No.14 ~ No.18 • USB problems → See No.19 ~ No.20 Problems 1. No picture • Indicator status: Off • Indicator status: Green • Indicator status: Yellow • Indicator status: Slowly flashing Yellow • Indicator status: Flashing Yellow (twice for each) 2.
English Problems Points to check with possible solutions 3. Display position is incorrect. Adjust the image position using the (p.23) If the problem persists, use the graphics board’s utility software to change the display position if available. 4. Screen image is smaller or larger than the actual screen images. Adjust the resolution using the (p.23) 5. Vertical bars of distortion appear. Decrease the vertical bars using the . (p.22) 6.
English Problems Points to check with possible solutions 11. The screen has defective pixels (e.g. slightly light or dark). This is due to the characteristics of the panel itself, and not the LCD product. 12. Fingerprints remain on the screen. Leaving the screen white may solve the problem. 13. The noise appears on the screen. Change the mode in in the menu. 14. The can not be selected. is disabled when the screen is displayed in the 1024 x 768.
English Problems Points to check with possible solutions 19. USB function cannot be setup. Check that the USB cable is correctly connected. Check that the PC and OS are USB compliant. (For verification of USB support, consult the manufacturer of each system.) Check the PC’s BIOS setting for USB. (For details, refer to the manual of the PC.) 20. PC is hung up. / The peripherals connected to the downstream ports do not operate. Check that the USB cable is correctly connected.
English 8. CLEANING Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime. NOTE • Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl alcohol), abrasive cleaners, or other strong solvents, as these may cause damage to the cabinet or LCD panel. Cabinet To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild detergent. Do not spray wax or cleaner directly into the cabinet.
English 9. SPECIFICATIONS LCD Panel 38 cm (15 inch), TFT color LCD panel with Anti-Glare Hard Coating, Viewing Angle: Horizontal: 160°, Vertical: 150° (at Contrast Ratio ≥ 5) Dot Pitch 0.280 mm Horizontal Scan Frequency 31 ∼ 61 kHz (Automatic) (Digital): 31 ~ 49 kHz Vertical Scan Frequency 50 Hz ∼ 85 Hz (Automatic) (1024 x 768: up to 75 Hz) (Digital): 60 Hz, (VGA TEXT : 70 Hz) Resolution 1024 dots x 768 lines Dot Clock (Max.
English Default settings Analog input Digital input Contrast 100% 100% Brightness 100% 100% Smoothing 3 ColorManagement Color Mode Standard Temperature Off (Normal white) PowerManager VESA DPMS Screen Size Full Input Priority Signal 1 Menu Off Timer DVI DMPM Disable Menu Settings Menu Size Normal Menu Off Timer 45 seconds Beep On Language English Beeper settings Short beep ScreenManager item selected. ScreenManager parameter adjusted to minimum or maximum limit.
English Pin Assignment DVI-I Connector 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 C1 C2 C3 C4 C5 Pin No. Signal Pin No. Signal Pin No.
English 10. GLOSSARY Afterimage The Afterimage is particular to LCD monitors when the monitor screen is left on for a long period without use. The “Afterimage” can be removed gradually by changing the displayed image. Clock With the analog input signal display, the analog signal is converted to a digital signal by the LCD circuitry. To convert the signal correctly, the LCD monitor needs to produce the same number clock pulse as the dot clock of the graphics system.
English Range Adjustment The Range Adjustment controls the level of output signal range to display the whole color gradation. Resolution The LCD panel consists of a fixed number of pixel elements which are illuminated to form the screen image. The EIZO L375 display panel consists of 1024 horizontal pixels and 768 vertical pixels. At a resolution of 1024 x 768, all pixels are displayed as a full screen.
APPENDIX/ANHANG/ANNEXE Preset Timing Chart for Analog input Timing-Übersichten für Analog Eingang Synchronisation des Signaux pour Analog numerique Based on the signal diagram shown below 15 factory presets have been registered in the monitor's microprocessor. Der integrierte Mikroprozessor des Monitors unterstützt 15 werkseitige Standardeinstellungen (siehe hierzu die nachfolgenden Diagramme).
Mode Dot Clock Sync Polarity MHz H kHz V Hz 25.175 Nega. Nega. 31.469 59.940 28.322 Nega. Posi. 31.468 70.087 30.24 Posi. Posi. 35.00 66.67 57.28 Posi. Posi. 49.73 74.55 31.5 Nega. Nega. 37.86 72.81 31.5 Nega. Nega. 37.50 75.00 36.0 Nega. Nega. 43.27 85.01 36.0 Posi. Posi. 35.16 56.25 40.0 Posi. Posi. 37.88 60.32 50.0 Posi. Posi. 48.08 72.19 49.5 Posi. Posi. 46.88 75.00 56.25 Posi. Posi. 53.674 85.061 65.0 Nega. Nega. 48.36 60.00 75.0 Nega.
C: Back Porch D: Blanking Period E: Display Period F: Total Cycle H µs/ Dot V ms/ Line H µs/ Dot V ms/ Line H µs/ Dot V ms/ Line H µs/ Dot V ms/ Line 1.589/ 40 1.907/ 54 3.175/ 96 3.911/ 224 3.810/ 120 3.810/ 120 2.222/ 80 3.556/ 128 2.200/ 88 1.280/ 64 3.232/ 160 2.702/ 152 2.462/ 160 19.20/ 144 2.235/ 176 0.794/ 25 1.111/ 35 1.114/ 39 0.784/ 39 0.528/ 20 0.427/ 16 0.578/ 25 0.626/ 22 0.607/ 23 0.478/ 23 0.448/ 21 0.503/ 27 0.600/ 29 0.513/ 29 0.466/ 28 5.720/ 144 6.356/ 180 7.407/ 224 5.
[Applicable to gray (standard color version only).] Congratulations! You have just purchased a TCO’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Environmental Requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs.
For U.S.A, Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZO NANAO TECHNOLOGIES INC. 5710 Warland Drive, Cypress, CA 90630 Phone: (562) 431-5011 declare that the product Trade name: EIZO Model: FlexScan L375 is in conformity with Part 15 of the FCC Rules.
Hinweis zur Ergonomie : Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1-ITB 2000 mit dem Videosignal, 1024 Punkte × 768 Zeilen, RGB analog, 0,7 Vp-p und mindestens 75,0 Hz Bildwiederholfrequenz, non interlaced. Weiterhin wird aus ergonomischen Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast.
