Important Please read PRECAUTIONS, this User’s Manual, and the Setup Guide (separate volume) carefully to familiarize yourself with safe and effective usage. • Please refer to the Setup Guide for basic information ranging from connection of the monitor to a PC to using the monitor. • The latest User’s Manual is available for download from our web site: http://www.eizo.
Location of Caution Statement This product has been adjusted specifically for use in the region to which it was originally shipped. If operated outside this region, the product may not perform as stated in the specifications. Copyright © 2011 EIZO NANAO CORPORATION All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO NANAO CORPORATION.
Notice for this monitor This product is suited to general purposes like creating documents, viewing multimedia content. This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is used outside the region, it may not operate as specified in the specifications. This product may not be covered by warranty for uses other than those described in this manual.
Cleaning Attention • Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel, and also quality deterioration of the image. • Never use any solvents or chemicals, such as thinner, benzene, wax, alcohol, and abrasive cleaner, which may damage the cabinet or panel. Note • The optional ScreenCleaner is recommended for cleaning the panel surface. ●●Panel • Clean the panel with a soft cloth such as a cotton cloth or lens cleaning paper.
CONTENTS Cover....................................................................... 1 Notice for this monitor.......................................... 3 Cleaning..................................................................... 4 ●●Panel................................................................ 4 ●●Cabinet............................................................. 4 To use the monitor comfortably.............................. 4 CONTENTS.......................................................
FCC Declaration of Conformity..............................51 Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor...................... 52 Hinweis zur Ergonomie :........................................ 52 LIMITED WARRANTY.............................................. 53 Recycling Information............................................ 62 China Measures for RoHS Compliance in ChinaRoHS.........................................................
Chapter 1 Introduction Thank you very much for choosing an EIZO color LCD monitor. 1-1. Features • • • • 23.0″ wide format LCD Applicable to the resolution of 1920 × 1080. IPS panel with 89° horizontal and vertical viewing angles (EV2335W only) Applicable to DisplayPort (applicable to 8 bit) (EV2335W only)*1 The image signal and audio signal can both be transmitted via a single DisplayPort cable. • The Color Mode function allows the user to select the display mode optimum to the displayed image.
*1 When transmitting an audio signal using the DisplayPort cable, the graphics board must be compatible with audio output (see “6-4. Specifications” (page 42)). *2 Reference values: EV2315W Maximum power consumption: 31 W (Brightness Max., speaker working, at default settings) Standard power consumption: 16 W (Brightness 120 cd/m 2, speaker not working, at default settings) EV2335W Maximum power consumption: 35 W (Brightness Max.
1-2. Controls and Functions Ex. EV2335W 17 Setting menu*1 16 15 18 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1. Ambient light sensor Detects ambient brightness. Auto EcoView function (page 33), EcoView Optimizer function (page 33). 2. Displays the setting menu of the power saving function (Auto EcoView (page 33) and EcoView Optimizer (page 33)). button 3. button button 4. button 5. button 6. 7. 8. button button Switches input signals for display (page 40).
1-3. EIZO LCD Utility Disk An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk contents and the overview of the software programs. ●●Disk contents and software overview The disk includes software programs for adjustment, and User’s Manual. Refer to Readme.txt file on the disk for software startup procedures or file access procedures. Item Overview Windows Macintosh √ √ √ - √ - User’s Manual of this monitor (PDF file) √ √ Readme.
2. Adjusting / Setting 1. Choose a menu to adjust / set with , , and then press . The Sub menu appears. 2. Choose an item to adjust / set with , , and then press . The adjustment / setting menu appears. 3. Adjust / set the selected item with , , and then press 3. Exiting 1. Choose “Return” from the Sub menu and press 2. Choose “Exit” from the Main menu and press . . The Setting menu appears. . The Setting menu quits. Note • The Setting menu can also be exited by pressing twice quickly.
●●Functions The following table shows all the Setting menu’s adjustment and setting menus. Main menu Color*1 Setting Brightness Contrast Temperature Gamma Advanced Settings Saturation Hue Overdrive*2 Gain Color Reset Screen Reference “2-3. Adjusting Color” (page 16) Screen Size Smoothing Analog Adjustment*3 Auto Screen Adjust Auto Range Adjust Clock Phase Hor.Position Ver.Position Source*2 “To reset the color adjustments” (page 30) “Screen Size Changing” (page 26) “2-4.
Chapter 2 Adjusting Screens 2-1. Compatible Resolutions The monitor supports the following resolutions. ●●EV2315W Analog Input (D-Sub) Resolution Applicable Signals 640 × 480 800 × 600 1024 × 768 1280 × 960 1280 × 1024 1280 × 720 1680 × 1050 1920 × 1080* VGA VESA VESA VESA VESA CEA-861 VESA CVT, VESA CVT RB CEA-861 Vertical Scan Frequency Dot Clock 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 148.5 MHz (Max.
●●EV2335W Analog Input (D-Sub) Resolution Applicable Signals 640 × 480 720 × 400 800 × 600 1024 × 768 1152 × 864 1280 × 960 1280 × 1024 1280 × 720 1680 × 1050 1920 × 1080* VGA, VESA VGA TEXT VESA VESA VESA VESA VESA CEA-861 VESA CVT, VESA CVT RB CEA-861 Vertical Scan Frequency Dot Clock ~75 Hz 70 Hz ~75 Hz ~75 Hz 75 Hz 60 Hz ~75 Hz 60 Hz 60 Hz 60 Hz 148.5 MHz (Max.
2-2. Setting the Resolution When you connect the monitor to the PC and find that the resolution is improper, or when you want to change the resolution, follow the procedure below. ●●Windows 7 1. Right-click the mouse anywhere on the desktop except for icons. 2. From the displayed menu, click “Screen resolution”. 3. On the “Screen Resolution” dialog box, select the monitor. 4. Click “Resolution” to select the desired resolution. 5. Click the “OK” button. 6.
2-3. Adjusting Color ●●To select the display mode (Color Mode) This function allows easy selection of a desired mode according to monitor application. Display Modes Mode Purpose User1 Select one of these user modes to define a desired set of parameter settings. User2 sRGB Suitable for color matching with sRGB compatible peripherals. Paper Produces a printed paper effect by decreasing contrast and color temperature. Movie Suitable for playing back animated images. The mode menu appears.
●●To perform advanced adjustments The “Color” menu of the Setting menu allows you to set and save the independent color adjustment for each mode. Attention • The monitor will take about 30 minutes before its internal electric components stabilize. Wait 30 minutes or more after turning the monitor power on before starting adjustment. • Perform the range adjustment first when adjusting color for analog signals (see “To adjust color gradation automatically” (page 25)).
●●To adjust brightness The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD back panel). Adjustable range 0 to 100 Procedure 1. Choose “Color” in the Setting menu, and press . . 2. Choose “Brightness” in the “Color” menu, and press The “Brightness” menu appears. 3. Use or for adjustment. to exit. 4. Press Note • While the Setting menu is not displayed, or is available for adjustment.
●●To adjust color temperature Color temperature can be adjusted. The color temperature is normally used to express the hue of “White” and / or “Black” by a numerical value. The value is expressed in degrees “K” (Kelvin). The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like the flame temperature. A gain preset value is set for each color temperature setting value.
●●To adjust the color saturation This function allows you to adjust color saturation. Adjustable range -50 to 50 Procedure 1. Choose “Color” in the Setting menu, and press . . 2. Choose “Advanced Settings” in the “Color” menu, and press . 3. Choose “Saturation” in the “Advanced Settings” menu, and press The “Saturation” menu appears. 4. Use or for adjustment. to exit. 5. Press Attention • Using this function may make some color gradations unavailable for display.
●●To set overdrive intensity (EV2335W only) This function allows you to set overdrive intensity based on the use of the monitor. You can reduce Image lags by setting it to “Enhanced” when displaying animated images. Adjustable range Enhanced, Standard, Off Procedure 1. Choose “Color” in the Setting menu, and press . . 2. Choose “Advanced Settings” in the “Color” menu, and press . 3. Choose “Overdrive” in the “Advanced Settings” menu, and press The “Overdrive” menu appears. 4. Use or for adjustment.
2-4. Screen Adjustment ●●Digital Signal Input When digital signals are input, images are displayed correctly based on the preset data of the monitor, but if characters and / or lines appear blurred, go to “To modify blurred characters / lines” (page 25). When performing more advanced adjustment, see “2-3. Adjusting Color” (page 16) and subsequent pages. ●●Analog Signal Input Attention • The monitor will take about 30 minutes before its internal electric components stabilize.
2. Prepare to use analog screen adjustment patterns. Load the “EIZO LCD Utility Disk” to your PC, and then open the “Screen adjustment pattern files”. Note • For details and instructions on opening the “Screen adjustment pattern files”, refer to the Readme.txt file. 3. Perform the auto adjustment again with the analog screen adjustment pattern displayed. ●●To adjust flickering, screen position, and screen size automatically Procedure 1.
●●To remove flickering or blurring Procedure . 1. Choose “Analog Adjustment” in the “Screen” menu, and press 2. Choose “Phase” in the “Analog Adjustment” menu, and press . The “Phase” menu appears. 3. Adjust the phase with 4. Press or to minimize flickering or blurring. to exit. When vertical bars appear on the screen after adjustment, go back to “To eliminate vertical bars ”.
5. Adjusting color gradation. ●●To adjust color gradation automatically Every color gradation (0 to 255) can be displayed by adjusting the signal output level. Procedure 1. Display Pattern 2 in full screen on the monitor using the “Screen adjustment pattern files”. 2. Choose “Screen” in the Setting menu, and press . 3. Choose “Analog Adjustment” in the “Screen” menu, and press . 4. Choose “Auto Range Adjust” in the “Analog Adjustment” menu, and press . The “Auto Range Adjust” menu appears. 5.
2-5. Screen Size Changing ●●Screen Size Changing The image with the resolution other than the recommended resolution is displayed in full screen automatically. You can change the screen size by using the “Screen Size” function. Setting Function Full Screen Displays an image in full screen. Images are distorted in some cases because the vertical rate is not equal to the horizontal rate. Enlarged Displays an image in full screen.
Chapter 3 Setting Monitor 3-1. Adjusting Volume This function allows you to adjust the volume. Adjustable range 0 to 30 Procedure . 1. Presss 2. Use or 3. Press for adjustment. to exit. Note • The volume for the speakers and the headphone can be set individually. 3-2. Switching sound source during DisplayPort signal input (EV2335W only) This function allows you to switch sound source during DisplayPort signal input. You can select the DisplayPort or Stereo Mini Jack. Procedure 1.
3-3. Switching Viewing Angle (EV2315W only) The viewing angle is adjusted so that the screen looks like a front view when the screen is looked up. Off -20 ° -40 ° Adjustable range -40 °, -20 °, Off Procedure 1. Choose “Monitor Settings” in the Setting menu, and press . . 2. Choose “Up View” in the “Monitor Settings” menu, and press The “Up View” menu appears. 3. Select “-40 °”, “-20 °”, or “Off” with or . to exit. 4.
3-6. Setting Orientation This function allows you to change the orientation of the Setting menu when using the monitor screen in vertical display position. Procedure . 1. Choose “Monitor Settings” in the Setting menu, and press . 2. Choose “Menu Settings” in the “Monitor Settings” menu, and press . 3. Choose “Orientation” in the “Menu Settings” menu, and press The “Orientation” menu appears. 4. Select “Landscape” or “Portrait” with 5. Press or . to exit. 6.
3-9. Setting Language This function allows you to select a language for the Setting menu or displaying message. Selectable languages English / German / French / Spanish / Italian / Swedish / Japanese / Simplified Chinese / Traditional Chinese Procedure . 1. Choose “Monitor Settings” in the Setting menu, and press . 2. Choose “Language” in the “Monitor Settings” menu, and press The “Language” menu appears. 3. Choose a language with or . to exit. 4. Press 3-10.
Chapter 4 Power Saving Functions 4-1. Setting Power Saving ●●Monitor This function allows you to set the monitor into the power saving mode according to the PC status. When the monitor has shifted to the power saving mode, the images on the screen are not displayed. Attention • Turning off the main power switch or unplugging the power cord completely shuts off power supply to the monitor. • Power consumption varies even when the stereo mini jack cable is connected.
●●To have further reduced power consumption When all the conditions below are met and the monitor shifts to the power saving mode, the power consumption is reduced to approx. 0.1 W. • The analog signal (D-Sub) is displayed. • “PowerManager” - “Off Timer”: Off • “Monitor Settings” - “Input Signal”: Manual • “Sound” - “Power Save”: Sound Off • EcoView NET is not installed on your PC. Note • This function can be disabled with the following procedures. 1. Press to turn off the monitor. 2.
4-3. Enabling / Disabling Automatic Brightness Adjustment The ambient light sensor on the front side of the monitor detects the environmental brightness to adjust the screen brightness automatically and comfortably by using the Auto EcoView function. Attention • Be careful not to block the ambient light sensor on the lower side of the monitor when using the Auto EcoView function. Procedure 1. Press . 2. Choose “Auto EcoView” in the “EcoView Menu” menu, and press . The “Auto EcoView” menu appears. 3.
4-5. Checking the power saving level The EcoView menu allows you to check Power Reduction, CO2 Reduction, and Eco Performance Level. The more indicators light up representing the Eco Performance Level, the higher the power saving level attained. Example: EV2335W Indicator Procedure 1. Press . The “EcoView Menu” menu appears. 4-6.
Chapter 5 Troubleshooting If a problem still remains after applying the suggested remedies, contact your local dealer. 5-1. No picture Problem 1. No picture • Power indicator does not light. • Power indicator is lighting blue. • Power indicator is lighting orange. • Power indicator flashes orange and blue. 2. The message below appears. • The message shows that the input signal is out of the specified frequency range.
5-2. Imaging problems (for both digital and analog) Problem 36 Possible cause and remedy 1. The screen is too bright or too dark. • Use “Brightness” or “Contrast” in the Setting menu to adjust it. (The LCD monitor backlight has a limited life span. When the screen becomes dark or begins to flicker, contact your local dealer.) • If the screen is too bright, turn on Auto EcoView and EcoView Optimizer. The monitor detects the environmental brightness to adjust the screen brightness automatically. 2.
5-3. Imaging problems (for digital only) Problem 1. The monitor configuration is changed to single under the multiple monitor configuration (when DisplayPort is connected) (EV2335W only) Possible cause and remedy • When two monitors are connected to one PC using DisplayPort, and the power to one of the monitors is turned off with the power button, the screen setting may be changed to the single monitor configuration. In such a case, enable the “DP HotPlug” function with the following procedures.
5-5. Other problems Problem 38 Possible cause and remedy 1. The Setting menu does not appear. • Check whether the operation lock function works (see “3-5. Locking Buttons” (page 28)). 2. The “Smoothing” on the Setting menu “Screen” cannot be selected. • You cannot choose “smoothing” when the screen is displayed in the following resolutions or settings. --The resolution is 1920 × 1080 --Screen Size is “Normal” 3. The auto adjustment function does not work.
Chapter 6 Reference 6-1. How to Attach the Optional Arm An optional arm (or an optional stand) can be attached by removing the stand section. Please refer to our web site for the corresponding optional arm (or optional stand). http://www.eizo.com Attention • When attaching an arm or stand, follow the instructions of their User’s Manual. • When using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to the VESA standard.
6-2. Connecting Multiple PCs The product has multiple connections to PCs and allows you to switch to one of the connections for display.
●●To set input signal selection Setting Function Auto The monitor recognizes the connector through which PC signals are input. When a PC is turned off or enters the power saving mode, the monitor automatically displays another signal. Manual The monitor detects only the PC’s signals currently displaying automatically. Select an active input signal with . Procedure . 1. Choose “Monitor Settings” from the Adjustment menu, and press . 2. Choose “Input Signal” from “Monitor Settings”, and press 3.
6-4. Specifications EV2315W LCD Panel Size 23.0-inch (580 mm) Type TFT color LCD Surface treatment Anti-Glare Hard Coating Viewingangles Horizontal 170 °, vertical 160 ° (CR≥10) Dot Pitch 0.2655 mm Response Time Black-white-black: Approx. 5 ms Horizontal Scan Analog Frequency Digital 31 - 68 kHz Vertical Scan Frequency Analog 55 - 61 Hz (non-interlace) Digital 59 - 61 Hz (non-interlace) 31 - 68 kHz Resolution 1920 Dots ×1080 Lines Max. Dot Clock 148.5 MHz Max. Display Color Approx.
Environmental Conditions Temperature Operating: 5 °C to 35 °C (41 °F to 95 °F) Storage: -20 °C to 60 °C (-4 °F to 140 °F) Humidity Operating: 20 % to 80 % R.H. (no condensation) Storage: 10 % to 90 % R.H. (no condensation) Air Pressure Operating: 700 to 1,060 hPa Storage: 200 to 1,060 hPa EV2335W LCD Panel Size 23.0-inch (580 mm) Type TFT color LCD Surface treatment Anti-Glare Hard Coating Viewingangles Horizontal 178 °, vertical 178 ° (CR≥10) Dot Pitch 0.
Mass Main unit Approx. 6.7 kg (14.8 lbs.) Main unit (without stand) Approx. 4.0 kg (8.8 lbs.) Movable range Environmental Conditions Temperature Humidity Air Pressure Tilt: 30 ° Up, 0 ° Down Swivel: 172 ° Right, 172 ° Left Adjustable height: 195 mm (165 mm (6.5 inch) for tilt of 0 °) Rotation: 90 ° (Clockwise) Operating: 5 °C to 35 °C (41 °F to 95 °F) Storage: -20 °C to 60 °C (-4 °F to 140 °F) Operating: 20 % to 80 % R.H. (no condensation) Storage: 10 % to 90 % R.H.
90 ° PIVOT φ209 61.5 (2.42) 209 (8.2) 245.5 (9.7) 29 (1.14) 29 (1.14) 125 (4.9) 30° TILT 240 (9.4) 121.2 (4.8)100 (3.9)112.8 (4.4) 360 (14.2) 320 (12.6) 345 (13.6) 184 (7.2) 240 (9.4) TILT 121.2 (4.8)100 (3.9)112.8 (4.4) 360 (14.2) 209 (8.2) 245.5 (9.7) 125 (4.9) 17.6 (0.69) 61.5 (2.42) 320 (12.6) 345 (13.6) 547 (21.5) 511.8 (20.1) 30° 2° 18.4 (0.72) 17.6 (0.69) 184 (7.2) 90 ° PIVOT 288.8 (11.4) 334 (13.1) 190~355 (7.5~14) 353~518 (13.9~20.4) 566.5~628.5 (22.3~24.7) 26.8 (1.
Accessories Signal cable Cleaning Kit MD-C87 (EV2335W only) EIZO “ScreenCleaner” For the latest information about the accessories, refer to our web site. http://www.eizo.
6-5. Glossary Clock The analog signal input monitor needs to reproduce a clock of the same frequency as the dot clock of the graphics system in use, when the analog signal is converted to a digital signal for image display. This is called clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the screen. DDC/CI (Display Data Channel / Command Interface) VESA provides the standardization for the interactive communication of the setting information, etc.
Overdrive This technology enhances response speed by increasing the potential difference at the time of motion of liquid-crystal pixels, and it is used for liquid-crystal TV sets and others in general. It provides clear-cut three-dimensional display with little afterimage, by improving response speed of the intermediate graduation range that frequently appears in moving images. Phase Phase means the sampling timing to convert the analog input signal to a digital signal.
Appendix Trademark The DisplayPort icon and VESA are trademarks and registered trademarks of the Video Electronics Standards Association in the United States and other countries. Windows, Windows Vista, Windows Media, SQL Server, and Xbox 360 are registered trademarks of Microsoft Corporation in the United States and other countries. Apple, Mac, Macintosh, iMac, eMac, Mac OS, MacBook, PowerBook, ColorSync, QuickTime, and iBook are registered trademarks of Apple Inc.
TCO This product has acquired the TCO standard that relates to the safety, ergonomics, environment and so forth of office equipment. For an overview of the TCO, refer to our web site. http://www.eizo.
FCC Declaration of Conformity For U.S.A. , Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZONANAOTECHNOLOGIESINC. 5710WarlandDrive,Cypress,CA90630 Phone:(562)431-5011 declare that the product Tradename:EIZO Model:FlexScanEV2315W/EV2335W is in conformity with Part 15 of the FCC Rules.
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörige Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden.
LIMITED WARRANTY LIMITED WARRANTY EIZO NANAO CORPORATION (hereinafter referred to as “EIZO”) and distributors authorized by EIZO (hereinafter referredtoasthe“Distributors”)warrant,subjecttoandinaccordancewiththetermsofthislimitedwarranty(hereinafter referred to as the “Warranty”), to the original purchaser (hereinafter referred to as the “Original Purchaser”) who purchasedtheproductspecifiedinthisdocument(hereinafterreferredtoasthe“Product”)from
BEGRENZTE GARANTIE EIZONANAOCORPORATION(imWeiterenals„EIZO“bezeichnet)unddieVertragsimporteurevonEIZO(imWeiteren als „Vertrieb(e)“ bezeichnet) garantieren dem ursprünglichen Käufer (im Weiteren als „Erstkäufer“ bezeichnet), der dasindiesemDokumentvorgegebeneProdukt(imWeiterenals„Produkt“bezeichnet)vonEIZOodereinemVertrieb erworbenhat,gemäßdenBedingungendieserbeschränktenGarantie(imWeiterenals„Garantie“bezeichnet),dass EIZO und der Vertrieb nach
GARANTIE LIMITÉE EIZONANAOCORPORATION(ci-aprèsdénommé«EIZO »)etlesdistributeursautorisésparEIZO(ci-aprèsdénommés «Distributeurs »),sousréserveetconformémentauxtermesdecettegarantielimitée(ci-aprèsdénommée«Garantie »),garantissentàl’acheteurinitial(ci-aprèsdénommé«Acheteur initial »)duproduitspécifiédanslaprésente(ci-après dénommé«Produit »)achetéauprèsd’EIZOoudeDistributeursagréésEIZO,queEIZOetsesDistributeursauront pouroptionderépareroure
GARANTÍA LIMITADA EIZO NANAO CORPORATION (en lo sucesivo “EIZO”) y sus distribuidores autorizados (en lo sucesivo los “Distribuidores”),conarregloydeconformidadconlostérminosdeestagarantíalimitada(enlosucesivola“Garantía”), garantizanalcompradororiginal(enlosucesivoel“Comprador original”)quecompróelproductoespecificadoeneste documento(enlosucesivoel“Producto”)aEIZOoasusDistribuidores,queEIZOysusDistribuidores,asupropio criterio,repararán
GARANZIA LIMITATA EIZONANAOCORPORATION(acuisifaràriferimentodaquiinpoicon“EIZO”)ediDistributoriautorizzatidaEIZO(a cuisifaràriferimentodaquiinpoicon“Distributori”)garantiscono,secondoiterminidiquestagaranzialimitata(acuisi faràriferimentodaquiinpoicon“Garanzia”)all’acquirenteoriginale(acuisifaràriferimentodaquiinpoicon“Acquirente originale”) che ha acquistato il prodotto specificato in questo documento (a cui si farà riferimento da
BEGRÄNSAD GARANTI EIZO NANAO CORPORATION (nedan kallat “EIZO”) och EIZOs auktoriserade distributörer (nedan kallade “Distributörer”) garanterar i enlighet med villkoren i denna begränsade garanti (nedan kallad “Garantin”) den ursprungligeköparen(nedankalladden“Ursprunglige köparen”)somköptedenidokumentetspecificeradeprodukten (nedankallad“Produkten”)frånEIZOellerDistributörer,attEIZOellerDistributörerenligtegetgottfinnandekostnadsfritt antingenreparer
ΠΕΡΙΟΡΙΣΜΕΝΗ ΕΓΓΥΗΣΗ ΗEIZONANAOCORPORATION(στοεξής«EIZO»)καιοιδιανομείςπουεξουσιοδοτείηEIZO(στοεξής«Διανομείς») παρέχουν εγγύηση, υποκείμενη και σύμφωνα με τους όρους της παρούσας περιορισμένης εγγύησης (στο εξής «Εγγύηση»),στοναρχικόαγοραστή(στοεξής«Αρχικός Αγοραστής»)οοποίοςαγόρασετοπροϊόνπουκαθορίζεταιστο παρόνέγγραφο(στοεξής«Προϊόν»)απότηνEIZOήτουςΔιανομείς,ηοποίαεξασφαλίζειότιηEIZOκαιοιΔιανομείς, σύμφωναμετηδιακριτήευχέρειάτους,είτε
ОГРАНИЧЕННАЯ ГАРАНТИЯ EIZO NANAO CORPORATION (называемая в дальнейшем “EIZO”) и авторизированные EIZO дистрибуторы (называемые в дальнейшем “Дистрибуторы”) гарантируют, в соответствии с условиями и пунктами этой ограниченной гарантии (называемой в дальнейшем “Гарантия”), первичному покупателю (называемому в дальнейшем“Первоначальный покупатель”),которыйприобрелуEIZOилиДистрибуторовпродукт,указанный в этом документе (называемый в дальнейшем “Продукт”), что E
有限责任保证书 EIZONANAO 有限公司(以下简称 EIZO )和 EIZO 授权的经销商(以下简称 经销商 ),接受并依照本有限责任保证书 (以下简称 保证书 )之条款,向从 EIZO 和经销商购买本文中所规定产品(以下简称 产品 )的原买方(以下称 原买方 ) 提供保证 :在保证期内(规定如下),如果原买方发现按本产品所附使用说明书(以下简称 用户手册 )所述方式正常使 用本产品过程中,本产品出现故障或损坏,EIZO 和经销商根据其独自的判断免费修理或更换该产品。 本保证期限定为 (i) 自本产品购买之日起的五 (5) 年期间或限定为到达(ii)使用本产品 3万小时的期限 , (以下简称 保证期限 ) 但本产品的液晶显示屏(LCD)的保证期限定为自本产品购买之日起的三 (3) 年期间。EIZO和经销商将不向原买方或任何 第三方承担本保证书所规定之外的与本产品有关的任何责任或义务。 本产品的任何部件停产七 (7) 年后,EIZO 和经销商将不再保留或保管任何这类部件。维修显示器时,EIZO 与经销商将使 用符合我方质量控制标准的替换零件。 本保证书仅对于设有经销商的国家或地区有效。本保证书并不限定
Recycling Information Recycling Information This product, when disposed of, is supposed to be collected and recycled according to your country’s legislation to reduce environmental burden. When you dispose of this product, please contact a distributor or an affiliate in your country. The contact addressees are listed on the EIZO website below. http://www.eizo.com For recycling information for customers in Switzerland, please refer to the following website. http://www.swico.
Πληροφορίες ανακύκλωσης Τοπροϊόναυτό,όταναπορρίπτεται,πρέπεινασυλλέγεταικαιναανακυκλώνεταισύμφωναμετηνομοθεσία τηςχώραςσαςέτσιώστεναμηνεπιβαρύνειτοπεριβάλλον.Γιανααπορρίψετετοπροϊόν,επικοινωνήστεμε έναναντιπρόσωποήμιαθυγατρικήεταιρείαστηχώρασας. ΟιδιευθύνσειςεπικοινωνίαςαναγράφονταιστηντοποθεσίαwebτηςEIZOπαρακάτω. http://www.eizo.
Informace o recyklaci Při likvidaci produktu musí být produkt vyzvednut a recyklován podle zákonů příslušné země, aby nedocházelo k zatěžování životního prostředí. Zbavujete-li se produktu, kontaktujte distributora nebo pobočkuvesvézemi.KontaktníadresyjsouuvedenynanásledujícíwebovéstráncespolečnostiEIZO. http://www.eizo.com Ringlussevõtu alane teave Keskkonnakoormuse vähendamiseks tuleks kasutatud tooted kokku koguda ja võtta ringlusse vastavalt teie riigi seadustele.
Информация относно рециклиране Приизхвърлянетонатозипродуктсепредлагасъбиранетоирециклиранетомусъобразнозаконитена вашатастраназадасенамализамърсяванетонаоколнатасреда.Когатоискатедасеосвободитеот тозипродукт,молясвържетесестърговскиямупредставителилисъссъответнитеорганиотговарящи затовавъввашатастрана. ДаннитезавръзкаснассаописанинаследнияИнтернетсайтнаEIZO: http://www.eizo.
China Measures for RoHS Compliance in ChinaRoHS 关于电子信息产品污染控制标识 本标识根据「电子信息产品污染控制管理办法」,适用于在中华人民共和国销售的电子信息产品。标识中央的 数字为环保使用期限的年数。只要您遵守该产品相关的安全及使用注意事项,在自制造日起算的年限内,不会 产生对环境污染或人体及财产的影响。上述标识粘贴在机器背面。 • 有毒有害物质或元素的名称及含量 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) 印刷电路板 × ○ ○ ○ ○ ○ 机箱 ○ ○ ○ ○ ○ ○ 液晶显示器 × ○ ○ ○ ○ ○ 其他 × ○ ○ ○ ○ ○ ○ :表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 规定的限量要求以下。 × :表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 规定的限量要求。 ( 企业可在此处 , 根据实际情況对上表中打“×” 的技术原因进行进一步说明 ) 66 Appe
5th Edition-October, 2011 03V23675E1 (U.