English User’s Manual FlexScan F520 Color Display Monitor
CONTENTS PRECAUTIONS ................................................................3 INTRODUCTION ...............................................................7 About This Manual ................................................................ 7 Controls & Connectors ......................................................... 7 Package Contents ................................................................ 7 1 INSTALLATION ............................................................
PRECAUTIONS IMPORTANT! * This product has been adjusted specifically for use in the region to which it was originally shipped. The performance of the product, (i.e. picture geometry, picture positioning and color convergence and purity in the case of color monitors) is optimally adjusted to the earth's magnetic field of the specific destination. If operated outside the region to which it was originally shipped, the product may not perform as stated in the specifications.
WARNING • If the monitor begins to emit smoke, smells like something is burning, or makes strange noises, disconnect all power connections immediately and contact your dealer for advice. Attempting to use a malfunctioning monitor can be dangerous. • Do not dismantle the cabinet or modify the monitor. Dismantling the cabinet or modifying the monitor may result in electric shock or burn. • Keep small objects away from the monitor.
• Do not overload your power circuit, as this may result in fire or electric shock. E • For proper connections of the power cord, be certain to plug the power cord to the provided monitor connector and directly to a wall outlet. By not doing so may result in fire or electric shock. • Handle the power cord with care. * Do not place the cord underneath the monitor or other heavy objects. * Do not pull on the cord. * Do not attempt to repair a damaged cord. If the power cord becomes damaged, stop using it.
• Do not remove the tilt-swivel stand. The stand is required to maintain clearance for the ventilation slots on the bottom of the cabinet. Removing the stand will block these slots and may result in fire or electric shock. • Do not touch the plug with wet hands. Touching the plug with wet hands is dangerous and can cause electrical shock.
INTRODUCTION About This Manual This manual explains the precautions, specifications, and operation of your EIZO monitor. Please read through this manual as it will help you to get the most out of your monitor.
1 INSTALLATION 1-1. Connecting the monitor to the PC 1) Be sure that the power switches of both the PC and the monitor are OFF. 2) Plug the signal cable into the connector at the rear of the monitor. • When connecting the signal cable or cable adapter, first check that the shape at the cable side matches the shape at the connecting side. After connecting, secure the connection with the screw-in fasteners. 3) Plug the other end of the cable into the video connector on the rear of the PC.
WARNING • Use the enclosed power cord. If using the power cord other than the enclosed one, use the following cord. In USA and Canada, use a UL LISTED/CSA LABELED or CERTIFIED power cord set meeting the following specifications: * Rating: min. 125 V, 10 A * Length: max. 2.0 m * Type: SVT * Plug type: NEMA 5-15P, Parallel blade, Grounding type, 125 V, 10 A In Europe, use a proper European standard approved power cord meeting the following specifications: * Rating: min. 250 V, 10 A * Length: max. 2.
2 SCREEN ADJUSTMENT 2-1. How to use the ScreenManager Entering the ScreenManager Press the ENTER key to display the ScreenManager Main menu. Main menu Making the Adjustments and Settings 1) Select the desired icon using the Arrow keys, and then press the ENTER key to display the each adjustment/setting menu. Adjustment menu 2) Use the Control pad (the four Arrow keys and the ENTER key) to make the required adjustments and settings.
OSD Contrast/ Brightness Function (Arrow Keys Used) E Adjusts: a) Contrast (left/right) b) Brightness (up/down) · When a white text against a black background (e.g., DOS text) is used, setting the brightness at its maximum is recommended because a dark setting will result in eye strain due to high character contrast.
OSD Function (arrow keys usd) Color Adjusts: Color temperature Temperature can be set from 6,500 K to 9,300 K, in 500 K increments. · Each monitor is slightly different, if two monitors are set to the same color temperature value (i.e. 6,500K), they may not necessarily look the same. PowerManager · VESA DPMS · Off Timer (Refer to the text below) Video Level Adjusts: Video Level Set the video level to adapt the output level of the computer or the graphics board.
VESA DPMS What is VESA DPMS? The acronym VESA stands for “Video Electronics Standards Association,” and DPMS stands for “Display Power Management Signaling.” DPMS is a communication standard that PCs and graphics boards use to implement power savings at the monitor side. Set-up Procedure 1) First, make the appropriate settings for the PC. 2) Select VESA DPMS icon in the ScreenManager’s PowerManager menu. 3) Select “On”.
To Delay Entering the “Off Timer Mode” To delay entering the “Off Timer Mode”, press any keys on the front panel located to the left of the power switch during the “Advance notice Mode”. The monitor will continue to operate for an additional 90 minutes. There will be another advance notice for 15 minutes as described. Delayed entrance into the “Off Timer Mode” can be extended as many times as desired. What is ENERGY STAR? “ENERGY STAR” is a set of power saving guidelines issued by the U.S.
3 TROUBLESHOOTING Troubleshooting If a problem persists even after applying the suggested remedies, contact an EIZO dealer. Problems Points to check with possible solutions 1) Indicator status: OFF Check that the power cord is correctly connected. 2) Indicator status: GREEN Check brightness and contrast settings. Minimum settings will cause screen to be blank. 3) Indicator status: GREEN (flashing) Try pressing a key on the keyboard, or clicking the mouse. (The monitor may be in a power saving mode.
Problems 8) The entire screen appears too dark or bright. Points to check with possible solutions Adjust the contrast and brightness using the ScreenManager. See page 10. Output level from the computer may not conform the monitor. Please set the video level using the ScreenManager. See page 12. Some signal timing can be the cause of this problem. To correct this, turn off the monitor, then hold down the AUTO-SIZING button and “down” arrow key while turning on the monitor again.
Problems 10) Moiré patterns are distracting. Points to check with possible solutions Reduce the moiré using the ScreenManager’s “Moiré” adjustment menu following the procedure below. 1) Set the desktop to an every-other-dot pattern so that moiré will be visible. 2) Go to the ScreenManager’s “Moiré” menu and adjust so that moiré becomes almost unnoticeable. See page 11. 3) Change to a different desktop background to reduce moiré even further.
4 CLEANING WARNING • Keep liquids away from the monitor. Spillage into the cabinet may result in fire, electric shock, or equipment damage. If an object or liquid falls/spills into the cabinet, unplug the monitor immediately. Have the unit checked by a qualified service engineer before using it again. Using the monitor in this condition could cause serious injury or equipment damage. CAUTION • To ensure safety, always unplug the monitor before cleaning it. Failure to do so may result in electric shock.
5 SPECIFICATIONS Electrical Specifications CRT 45 cm (17 inch) class, 90° deflection Invar Shadow Mask with Anti- Reflective SuperErgoCoat® CRT AG Pitch 0.26 mm Scan Frequency(Horizontal): 30 kHz-96 kHz (Automatic) Scan Frequency (Vertical): 50 Hz-160 Hz (Automatic) Max. Active Display Area 318 mm (H) × 238 mm (V) (12.5” (H) × 9.3” (V)) (Viewable image size: 397 mm (15.6”)) * Display size can be set by the user through microprocessor control panel.
Preset Timing 8 factory presets shown below have been registered in the monitor’s microprocessor. Resolution Frequencies Interlace fH (kHz) fV (Hz) Sync Polarity Video Signal Level VGA (text) 720 × 400 31.47 70.09 Non H/Negative V/Positive 0.7V(p-p)/75Ω VGA 640 × 480 31.47 59.94 Non H/Negative V/Negative 0.7V(p-p)/75Ω VESA 640 × 480 37.50 75.00 Non H/Negative V/Negative 0.7V(p-p)/75Ω VESA 800 × 600 46.88 75.00 Non H/Positive V/Positive 0.7V(p-p)/75Ω VESA 1024 × 768 60.
Congratulations! You have just purchased a TCO’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs.
For U.S.A, Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZO Nanao Technologies Inc. 5710 Warland Drive, Cypress, CA 90630 Phone: (562) 431-5011 declare that the product Trade name: EIZO Model: FlexScan F520 is in conformity with Part 15 of the FCC Rules.
Hinweis zur Ergonomie : Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1/59-98, EK1/60-98 mit dem Videosignal, 1024 Punkte x 768 Zeilen, RGB analog, 0,7 Vp-p und mindestens 85,0 Hz Bildwiederholfrequenz, non interlaced. Weiterhin wird aus ergonomischen Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast.) PTB Hinweis Eigensichere Kathodestranlröhre nach Anlage III Röntgenverordnung.
