ENGLISH 1
SAFETY SYMBOLS This manual uses the safety symbols below. They denote critical information. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety. Copyright© 2001 by EIZO NANAO CORPORATION. All rights reserved.
CONTENTS PRECAUTIONS ............................................................................. 4 1. INTRODUCTION ............................................................................ 8 2. ENGLISH 1-1. Features ....................................................................................................... 8 1-2. Package Contents ........................................................................................ 8 1-3. Controls & Connectors .........................................
PRECAUTIONS IMPORTANT! • This product has been adjusted specifically for use in the region to which it was originally shipped. If operated outside the region to which it was originally shipped, the product may not perform as stated in the specifications. • To ensure personal safety and proper maintenance. Please read this section and the caution statements on the monitor (refer to the figure below). [Location of the Caution Statements] The equipment must be connected to a grounded main outlet.
WARNING ENGLISH • Place the unit on a strong, stable surface. A unit placed on an inadequate surface may fall, resulting in injury or equipment damage. If the unit falls, disconnect the power immediately and have the unit checked by a qualified service engineer before using it again. Using a unit after it has been dropped may result in fire or electric shock. OK • Set the unit in an appropriate location. Not doing so may cause damage and could result in fire or electric shock. * Do not place in outdoors.
WARNING • Use the correct voltage. * The unit is designed for use with a specific voltage only. Connection to another voltage than specified in this User’s Manual may cause fire, electric shock, or other damage. * Do not overload your power circuit, as this may result in fire or electric shock. * For proper connections of the power cord, be certain to plug the power cord to the provided unit connector and directly to a wall outlet. Not doing so may result in fire or electric shock.
CAUTION • Do not move it alone. Always work with another person. Moving it alone may cause lower back pain. Also note that the unit is heavier at the front than at the rear. ENGLISH • Handle with care when carrying the unit. Disconnect the power cord and signal cables and remove the optional unit. Moving the unit with the cord or the option attached is dangerous. It may result in injury or equipment damage. OK • Do not block the ventilation slots on the cabinet.
1. INTRODUCTION Thank you very much for choosing an EIZO Color Display Monitor. 1-1. Features • Horizontal scanning frequency of 30-130 kHz Vertical scanning frequency of 50-160 Hz • Fine contrast function with a wider margin provides for a more brightly contrasted picture (See page 15) • Power saving system and off timer system (See page 16) • Adjustment lock function, to prevent any accidental changes (See page 17) • Dual inputs with individual color configuration (See page 17) 1-2.
1-3.
2. INSTALLATION 2-1. Connecting the monitor to the PC • Be sure that the power switches of both of the PC and the monitor are OFF. 1. Plug the signal cable into the connector at the rear of the monitor and the other end of the cable into the video connector on the PC. After connecting, secure the connection with the screw-in fasteners.
2. Plug the power cord into the power connector at the rear of the monitor. Then, plug the other end of the cord into a power outlet. ENGLISH WARNING WARNING • Use the enclosed power cord and connect to the standard power outlet of your country. Be sure to remain within the rated voltage of the power cord. Not doing so may cause in fire or electric shock. • The equipment must be connected to a grounded main outlet. Not doing so may cause in fire or electric shock. 3.
2-2. Getting Ready for Operation Try each setting procedure if necessary in the following cases. 1. The display image size and/or position is incorrect Æ Press the AUTO-SIZING button on the front panel. The AUTO-SIZING function centers the displayed image, aligning the image’s borders with respect to the monitor frame. In general, press the AUTO-SIZING button whenever changing the graphics board or the resolution p.25), or when image size and/or position is incorrect. 2.
3. SCREEN ADJUSTMENT • Allow the monitor to stabilize for at least 30 minutes before making image adjustments. Use the control pad on the front panel. The control pad can be pressed in 5 directions, “Enter”, “Up”, “Down”, “Left” and “Right”. 1. Up Left Enter Right Down Entering the ScreenManager Display the ScreenManager “Main menu” by pressing the “Enter” of the control pad. Main menu displays the current connector type and frequency of the input signal. Main menu Æ 2.
Adjustments and Settings Main menu Sub menu Adjustments and Settings See page Contrast — Screen contrast and brightness* — Size — Screen size — Position — Screen position — Side Pin Side pin balance — Trapezoidal Distortion — Tilt Inclination Screen Uniformity Convergence Uniformity Convergence Moiré Reduction Moiré Fine Contrast Signal Filter 1 Signal Filter 2 Color Color Mode — p.25) p. 20 p.24) p. 20 p.24) p. 19 To brighten the photo, picture image or movie p.
3-2. Color Adjust the color using by menu. 1. To set the color temperature ENGLISH Æ Set the . Temperature can be set from 4,000 K to 10,000 K, in 500 K increments. (Including the 9,300 K default setting.) 2. To adjust each color tone, (Red, Green and Blue) Æ Adjust the p.24) and p.24). Change the to . The values shown in percentages (%) for both the Cutoff and Gain are available only as a reference tool.
3-4. Power Save There are two power save settings choose the setting which matches your environment. Set the power saving setting by using menu. • Do your part to conserve energy, turn off the monitor when you are finished using it. Complete energy use can only be accomplished by disconnecting the monitor’s power supply cord from the plug receptacle. 1. To use the PC’s power saving system (VESA DPMS Æ p.25) ) Select “ON” in the menu.
3-5. Adjustment Lock [To lock] Press on the AUTO-SIZING button while switching on the monitor’s power. [To unlock] Switch off the monitor’s power, then hold down the AUTO-SIZING button once again and turn the power back on. 3-6. Connecting two PCs to the Monitor Two PCs can be connected to the monitor through the BNC/D-Sub input connections on the back of the monitor. (Example) 1.
4. TROUBLESHOOTING If a problem persists even after applying the suggested remedies, contact an EIZO dealer. *The bracket < > indicates the function of ScreenManager Problems 1. No picture • Indicator status: Off • Indicator status: Green • Indicator status: Flashing Green / Yellow • Indicator status: Flashing Yellow 2. Following messages appear. •“No signal detected” error message appears. •“Out of range” error message appears.
Problems Points to check with possible solutions Use of the adjustment may cause a slight vibration. To eliminate the vibration, set the adjustment level to lower percentage or 0%. If the volume level of the EIZO optional i·Sound speaker is too high, it may, in some cases, cause a slight vibration. To eliminate, turn down the volume of the speaker. 4. The image is flickering. Flicker will occur with interlaced scanning, or noninterlaced scanning with a low refresh rate.
Problems Points to check with possible solutions 8. The entire screen appears too dark or bright. Adjust the (Contrast and Brightness). Some signal timing can be the cause of this problem. To correct this, turn off the monitor, then hold down the “down” arrow key while turning on the monitor again. This will change the signal timing and brighten the screen. If the above operation is repeated, the screen becomes dark again. 9. Color is abnormal. • The entire screen appears bluish or reddish.
5. CLEANING Periodic cleaning is recommended to keep the monitor looking new and to prolong its operational lifetime. Clean the cabinet and CRT areas as follows: ENGLISH • Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl alcohol), abrasive cleaners, or other strong solvents, as these may cause damage to the cabinet or CRT. Cabinet To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild detergent. Do not spray wax or cleaner directly onto the cabinet.
6. SPECIFICATIONS CRT CRT Dot Pitch Scan Frequency Horizontal Vertical Recommended Resolution Max. Active Display Area*1 Power Supply Power Consumption Input Connector Input Signal Sync Video Signal registration Plug & Play Dimensions Weight Temperature Humidity Certifications and Standards 100-120 VAC 55 cm (21 inch) class, 90° deflection Invar Shadow Mask with Anti Reflective SuperErgoCoat® 0.25 mm (Horizontal: 0.
Preset Timing Resolution fH(kHz) fV(Hz) Interlace Sync Polarity Video Signal Level 720 x 400 31.47 70.09 Non H./Negative V./Positive 0.7 V(p-p)/75Ω VESA 1600 x 1200 106.25 85.00 Non H./Positive V./Positive 0.7 V(p-p)/75Ω Dimensions 486 (19.1) mm (inches) 368.6 (14.5) 494 (19.4) ENGLISH VGA (text) 400 (15.7) 298 (11.7) 127 306 ( 12.0) 72.5 (5.0) (2.9) 44.9 (1.8) 520 (20.5) SIDE FRONT TOP Pin Assignment * D-Sub mini 15 pin connector No. Signal No.
7. GLOSSARY Color Temperature Color temperature is a method to measure the white color tone, generally indicated in degrees Kelvin. At high temperatures the white tone appears somewhat blue, while at lower temperatures it appears somewhat red. Computer monitors generally give best performance at high temperature settings. 5,000K: Often used in printing industry. 6,500K: Good for video-image display. 9,300K: Default setting for your EIZO monitor.
Resolution Uniformity The uniformity is the purity of the color when a white screen is displayed on screen. Some monitors have blue or pink tinted areas that exhibit poor white uniformity. Some monitors have some brighter and darker areas, then this is an indication of bright uniformity error. VESA DPMS The acronym VESA stands for “Video Electronics Standards Association,” and DPMS stands for “Display Power Management Signaling.
8.
Congratulations! You have just purchased a TCO’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs.
For U.S.A, Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZO NANAO TECHNOLOGIES INC. 5710 Warland Drive, Cypress, CA 90630 Phone: (562) 431-5011 declare that the product Trade name: EIZO Model: FlexScan F931 is in conformity with Part 15 of the FCC Rules.
Hinweis zur Ergonomie : Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1/59-98, EK1/6098 mit dem Videosignal, 1600 Punkte x 1200 Zeilen, RGB analog, 0,7 Vp-p und mindestens 85,0 Hz Bildwiederholfrequenz, non interlaced. Weiterhin wird aus ergonomischen Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast.
