Important Please read PRECAUTIONS, this User’s Manual, and Setup Manual (separate volume) carefully to familiarize yourself with safe and effective usage. • Please refer to the Setup Manual for basic information ranging from connection of the monitor to a PC to using the monitor. • The latest User’s Manual is available for download from our web site: http://www.radiforce.
Product specification may vary with sales areas. Confirm the specification in the manual written in language of the region of purchase. Copyright© 2011 EIZO NANAO CORPORATION All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO NANAO CORPORATION.
Notice for this monitor This product is suited to display medical images of such modalities as MRI, CT, PET, and operating room (RX430-FC only). It does not support the display of mammography images for diagnosis. This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is used outside the region, it may not operate as specified in the specifications. This product may not be covered by warranty for uses other than those described in this manual.
Cleaning Attention • Never use any solvents or chemicals, such as thinner, benzene, wax, alcohol, and abrasive cleaner, which may damage the cabinet or panel. Note • Optional ScreenCleaner is recommended for cleaning the panel surface. (“ScreenCleaner” is supplied with RX430FC.) ●●Panel • Clean the panel with a soft cloth such as cotton cloth or lens cleaning paper. • If necessary, stubborn stains can be removed by moistening part of a cloth with water to enhance its cleaning power.
CONTENTS Cover....................................................................... 1 3-4. Setting the EIZO Logo Display ..... 20 Notice for this monitor............................................. 3 3-5. Locking Buttons ..................... 20 CONTENTS.............................................................. 5 3-6. Enabling/Disabling DDC communication. 20 Introduction........................................ 7 3-7. Enabling/Disabling DC5V output................21 3-8.
Appendix............................................................... 41 Trademark.................................................................41 License......................................................................41 Medical Standard.................................................... 42 FCC Declaration of Conformity............................. 43 EMC Information..................................................... 44 LIMITED WARRANTY...............................................
Chapter 1 Introduction Thank you very much for choosing an EIZO color LCD monitor. 1-1. Features • 29.8 inches • Applicable to the resolution of 4M pixels (2560 × 1600 dots) • Uses high-contrast panel (1100:1). Enables the display of sharp images. • Applicable to DisplayPort (applicable to 8 bit or 10 bit, not applicable to audio signals) • The Hybrid Gamma function automatically identifies the display area for the monochrome and color images on the same screen, and displays each set status.
1-2. EIZO LCD Utility Disk An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk contents and the overview of the software programs. ●●Disk contents and software overview The disk includes software programs for adjustment, and User's Manual. Refer to Readme.txt file on the disk for software startup procedures or file access procedures. Item Overview Readme.
1-3. Basic Operations and Functions ●●Basic Adjustment menu operations 1. Displaying Adjustment Menu 1. Press . The Adjustment menu appears. Menu title Current mode Setting Settings Menu 2. Adjusting/Setting 1. Choose a menu to adjust/set with , , and then press . 2. Choose a menu to adjust/set with , , and then press . 3. Adjust/set the selected item with , , and then press . 3. Exiting 1. Press a few times. The Adjustment menu finishes.
●●Functions The following table shows all the Adjustment menu’s adjustment and setting menus. Main menu Color Setting Reference “2-2. Adjusting Color” (page 12) Brightness Contrast Temperature Gamma Advanced Settings Hue Saturation Gain Hybrid Area Detection Type Highlight Area Color Reset “3-9. Return To Default Setting” (page 22) SelfCalibration “4-1. Executing Calibration ” (page 23) Grayscale Check “4-2. Checking Grayscale ” (page 24) Settings “4-3.
Chapter 2 Adjusting Screens 2-1. Setting the Resolution ●●Display resolution For details on compatible resolutions, refer to “Compatible Resolutions” in the Setup Manual. ●●Setting resolution When you connect the monitor to the PC and find that the resolution is improper, or when you want to change the resolution, follow the procedure below. Windows 7 1. Right-click the mouse anywhere on the desktop except for icons. 2. From the displayed menu, click “Screen resolution”. 3.
2-2. Adjusting Color ●●To select the display mode (CAL Switch mode) This function allows easy selection of a desired mode according to monitor application. Display Modes Mode Purpose 1-DICOM Available to display in DICOM mode. 2-Custom Select one of these user modes to define a desired set of parameter settings. 3-CAL1 Displays the screen adjusted by calibration software.
●●Adjustable settings in each mode The adjustable settings depend on the mode. (You cannot select any non-adjustable or non-settable function.
●●To adjust contrast The luminance of the screen is adjusted by varying the video signal level. Adjustable range 0 to 100% Procedure . 1. Choose from the Adjustment menu, and press 2. Choose from , and press . The appears. 3. Use or for adjustment. to exit. 4. Press Note • In the contrast of 100%, every color gradation is displayed.
●●To adjust gamma Gamma can be adjusted. The brightness of the monitor varies depending on the input signal, however, the variation rate is not proportional to the input signal. To keep the balance between the input signal and the brightness of the monitor is called as “Gamma correction”. Adjustable range 1.6 to 2.7 Procedure 1. Choose from the Adjustment menu, and press 2. Choose from , and press 3. Use or . . for adjustment. to exit. 4.
●●To adjust gain The brightness of each color component red, green, and blue is called “Gain”. You can change the hue of “white” by adjusting gain. Adjustable range 0 to 100% Procedure 1. Choose from the Adjustment menu, and press . 2. Choose from , and press . 3. Choose , and press . 4. Choose the color to adjust from , , and , and then press 5. Use or . for adjustment. to exit. 6.
●●To set the detection type in the monochrome image display area You can set the detection type in the monochrome image display area. Attention • When the detection type is changed, the display area is highlighted for 5 seconds even if is “Off”. Adjustable range Off, Type-1, Type-2, Type-3 Procedure . 1. Choose from the Adjustment menu, and press 2. Choose from , and press 3. Use or 4. Press for adjustment. to exit.
2-3. Screen Size Selection ●●To change screen size The image with the resolution other than the recommended resolution is displayed in full screen automatically. You can change the screen size by using the function from . Setting Function Full Displays an image in full screen. Images are distorted in some cases because the vertical rate is not equal to the horizontal rate. Enlarged Displays an image in full screen.
Chapter 3 Setting Monitor 3-1. Enabling/Disabling Mode Selection Allows you to select the specified modes only. Use this function when all the display modes are not available or when keeping the display mode unchanged. Procedure . 1. Choose from the Adjustment menu, and press 2. Choose from , and press 3. Use or to select the mode to change, and press 4. Select “On” or “Off” with 5. Press . . or . to exit. Attention • You cannot set all the modes disable.
3-4. Setting the EIZO Logo Display This function allows you to display, or not, the EIZO logo. Procedure 1. Press to turn off the monitor. down, press 2. Holding for at least two seconds to turn on the monitor. The Optional Settings menu appears. 3. Choose from , and press 4. Select ”On” or “Off” with 5. Select “Finish” with or , and press . . or . . 6. Press The Optional Settings menu is closed. 3-5.
3-7. Enabling/Disabling DC5V output This function allows you to enable/disable the DC5V output. Procedure 1. Press to turn off the monitor. down, press 2. Holding for at least two seconds to turn on the monitor. The Optional Settings menu appears. 3. Choose from , and press 4. Select ”On” or “Off” with 5. Select “Finish” with or , and press . . or . . 6. Press The Optional Settings menu is closed. 3-8.
3-9. Return To Default Setting There are two different Resets: Color Reset for only resetting the color adjustments to the default settings and All Reset for resetting all settings to the defaults. Attention • After resetting, you cannot undo the operation. Note • Regarding the default setting, see “Main Default Settings” (page 37). ●●To reset the color adjustment value This function only resets the color adjustment value for the currently selected mode to the default settings. Procedure .
Chapter 4 Controlling Monitor Quality This product has the built-in Integrated Front Sensor, which allows the user to perform periodic calibration and Grayscale Check for the monitor independently. Note • To perform advanced quality control that conforms to medical standards, use the optional monitor quality control software kit “RadiCS UX1”. • “RadiCS UX1” allows you to set the adjustment target and schedule for the calibration and Grayscale Check.
4-2. Checking Grayscale This function allows you to execute Grayscale Check and view the latest result. In addition, when the schedule is set using RadiCS, the next grayscale check schedule appears. ●●Executing Grayscale Check Procedure . 1. Choose from the Adjustment menu, and press 2. Choose from , and press 3. Select “Execute” with 4. Press . or . to exit. Grayscale Check is executed.
Chapter 5 Power Saving Functions 5-1. Setting Power Saving This function allows you to set the monitor into the power saving mode according to the PC status. When the monitor has shifted to the power saving mode, the images on the screen are not displayed. Attention • Turning off the main power switch or unplugging the power cord completely shuts off power supply to the monitor.
5-3. Setting the power saving mode when a person leaves the monitor The sensor on the front side of the monitor detects the movement of a person by setting a value from “Level-1” to “Level-4” of the Presence Sensor function. When a person moves away from the monitor, it shifts to the power saving mode automatically and does not display the images on the screen to reduce the power consumption.
Chapter 6 Troubleshooting If a problem still remains after applying the suggested remedies, contact your local dealer. No picture Problem 1. No picture • Power indicator does not light. Possible cause and remedy • Check whether the power cord is connected properly. • Turn off the main power, and then turn it on again a few minutes later. • Turn the main power switch on. • Press . • Power indicator is lighting green.
Problem • The message shows that the input signal is out of the specified frequency range. (Such signal frequency is displayed in magenta.) Example: Possible cause and remedy • Check whether the PC is configured to meet the resolution and vertical scan frequency requirements of the monitor (see “Compatible Resolutions” in the Setup Manual.). • Reboot the PC. • Select an appropriate display mode using the graphics board’s utility. Refer to the manual of the graphics board for details.
Other problems Problem Possible cause and remedy 8. The adjustment menu does not appear. • Check whether the operation lock function works (see “3-5. Locking Buttons ” (page 20)). 9. No mode menu is displayed. • Check whether the operation lock function works (see “3-5. Locking Buttons ” (page 20)). 10. (When using Presence Sensor) The images remains to be displayed when you move away from the monitor. The images does not reappear when you come near it.
Error Code 30 Details **34 • The sensor may not have worked correctly. • Turn off the main power, wait for a few minutes before turning the power back on, and then execute SelfCalibration/Grayscale Check again. **94 • is “Enlarged” or “Full”, and SelfCalibration or Grayscale Check cannot be executed. • Set to “Normal”. **95 • The execution conditions for SelfCalibration or Grayscale Check may not be appropriate.
Chapter 7 Reference 7-1. How to Attach the Optional Arm An optional arm (or an optional stand) can be attached by removing the stand section. (The stand is not supplied with RX430-FC.) Attention • When attaching an arm or stand, follow the instructions of their User’s Manual. • When using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to the VESA standard. - Clearance between the screw holes: 200 mm × 100 mm - Thickness of plate: 2.
7-2. Connecting Multiple PCs The product has multiple connections to PCs and allows you to switch to one of the connections for display. Connection examples DVI-D connector DisplayPort connector Digital (DisplayPort) Digital (DVI) Signal cable (supplied DD200-DL) Signal cable (supplied PP200) DisplayPort connector DVI connector To PC 1 To PC 2 ●●To switch among input signals Procedure 1. Choose from the Adjustment menu, and press 2. Choose from , and press 3.
●●To set input signal selection Setting Function Auto The monitor recognizes the connector through which PC signals are input. When a PC is turned off or enters the powersaving mode, the monitor automatically displays another signal. Manual The monitor detects only the PC's signals currently displaying automatically. Select an active input signal with . Procedure . 1. Choose from the Adjustment menu, and press 2. Choose from , and press 3.
7-3. Making Use of USB (Universal Serial Bus) This monitor has a hub compatible with USB. Connected to a PC compatible with USB or another USB hub, this monitor functions as a USB hub allowing connection to peripheral USB devices. ●●Required System Environment 1. A PC equipped with a USB port or another USB hub connected to a USB compatible PC 2. Windows 2000/XP/Vista/7 or Mac OS 9.2.2 and Mac OS X 10.2 or later 3.
7-4. Displaying monitor information ●●Displaying signal information This function displays the information about the current input signals displayed. Procedure . 1. Choose from the Adjustment menu, and press 2. Choose from , and press . The Signal Info screen appears. (Example) ●●Displaying Monitor Information This function displays the information about the monitor. Procedure . 1. Choose from the Adjustment menu, and press 2.
7-5. Specifications LCD Panel Size 29.8-inch (756 mm) TFT color LCD Surface treatment RX430: Anti-glare, hard coating RX430-AR: Anti-reflection RX430-FC: AR coating (both sides) RX430: 2H RX430-AR: 2H Surface hardness RX430-FC: 3 H or more Visible reflectance RX430-FC: 0.8% or less Visible light transmittance RX430-FC: 95% or more Viewing angles Viewing angles: Horizontal 170°, vertical 170° (CR≥50) Dot pitch 0.2505 mm Response time Black-white-black: Approx.
Environmental conditions USB Temperature Operating: Storage: -20°C to 60°C (-4°F to 140°F) Humidity Operating: 20% to 80% R.H. (no condensation) Storage: 10% to 80% R.H. (no condensation) Air pressure Operating: 700 to 1,060 hPa Storage: 200 to 1,060 hPa Standard USB Specification Revision 2.0 Port Upstream port × 1, Downstream port × 2 Communication Speed 480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low) Supply current Downstream: Max.
Outside Dimensions unit : mm (inch) RX430/RX430-AR 76.7 (3.02) 119 (4.7) 172° 172° 648 (25.5) SWIVEL RANGE 319 (12.6) 25° TILT RA NGE 310 (12.2) 100 (3.9) 310 (12.2) 256.5 (10.1) 18.5 (0.73) 202 (8.0) 496 (19.5) 25° 131 (5.2) 25.5 (1.00) 296 (11.7) 383.5 (15.1) 100 (3.9) 661 (26.0) 381 (15.0) 190.5 (7.5) 15.5 (0.61) 50.7 (2.00) 627 (24.7) 196 (7.7) 44.5 (1.75) 38.35 (1.51) 402.8 (15.9) 498 (19.6) 38.35 (1.51) 720 (28.3) 643.3 (25.3) 67 (2.64) 348 (13.7) 255 (10.0) 281.5 (11.
7-6. Glossary DDC (Display Data Channel) VESA provides the standardization for the interactive communication of the setting information, etc. between a PC and the monitor. DICOM (Digital Imaging and Communication in Medicine) The DICOM standard was developed by the American College of Radiology and the National Electrical Manufacturer’s Association of the USA. The DICOM compatible device connection enables to transfer the medical image and information.
HDCP (High-bandwidth Digital Content Protection) Digital signal coding system developed to copy-protect the digital contents, such as video, music, etc. This helps to transmit the digital contents safely by coding the digital contents sent via the DVI or HDMI connector on the output side and decoding them on the input side. Any digital contents cannot be reproduced if both of the equipments on the output and input sides are not applicable to HDCP system.
Appendix Trademark The DisplayPort icon and VESA are trademarks and registered trademarks of the Video Electronics Standards Association in the United States and other countries. Windows, Windows Vista, Windows Media, and Xbox 360 are registered trademarks of Microsoft Corporation in the United States and other countries. Apple, Mac, Macintosh, iMac, eMac, Mac OS, MacBook, PowerBook, ColorSync, QuickTime, and iBook are registered trademarks of Apple Inc.
Medical Standard • It shall be assured that the final system is in compliance to IEC60601-1-1 requirement. • Power supplied equipment can emit electromagnetic waves, that could influence, limit or result in malfunction of the monitor. Install the equipment in a controlled environment, where such effects are avoided. • This is a monitor intended for use in a medical image system. It does not support the display of mammography images for diagnosis.
FCC Declaration of Conformity For U.S.A. , Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZONANAOTECHNOLOGIESINC. 5710WarlandDrive,Cypress,CA90630 Phone:(562)431-5011 declare that the product Tradename:EIZO Model:RadiForceRX430 is in conformity with Part 15 of the FCC Rules.
EMC Information Essential performance of RadiForce series is to display images and operate functions normally. CAUTION The RadiForce series requires special precautions regarding EMC and need to be installed, put into service and used according to the following information. Do not use any cables other than the cables that provided or specified by us. Using other cables may cause the increase of emission or decrease of immunity.
Guidance and manufacturer’s declaration - electromagnetic immunity TheRadiForceseriesisintendedforuseintheelectromagneticenvironmentspecifiedbelow.Thecustomerortheuser oftheRadiForceseriesshouldassurethatitisusedinsuchanenvironment. Immunity test ConductedRF IEC/EN61000-4-6 RadiatedRF IEC/EN61000-4-3 IEC/EN60601 test level Compliance level Electromagnetic environment - guidance 3Vrms 150kHzto80MHz 3Vrms 3V/m 80MHzto2.
Recommended separation distances between portable and mobile RF communications equipment and the RadiForce Series TheRadiForceseriesisintendedforuseinanelectromagneticenvironmentinwhichradiatedRFdisturbances arecontrolled.
LIMITED WARRANTY LIMITED WARRANTY EIZO NANAO CORPORATION (hereinafter referred to as “EIZO”) and distributors authorized by EIZO (hereinafter referredtoasthe“Distributors”)warrant,subjecttoandinaccordancewiththetermsofthislimitedwarranty(hereinafter referred to as the “Warranty”), to the original purchaser (hereinafter referred to as the “Original Purchaser”) who purchasedtheproductspecifiedinthisdocument(hereinafterreferredtoasthe“Product”)from
BEGRENZTE GARANTIE EIZONANAOCORPORATION(imWeiterenals„EIZO“bezeichnet)unddieVertragsimporteurevonEIZO(imWeiteren als „Vertrieb(e)“ bezeichnet) garantieren dem ursprünglichen Käufer (im Weiteren als „Erstkäufer“ bezeichnet), der dasindiesemDokumentvorgegebeneProdukt(imWeiterenals„Produkt“bezeichnet)vonEIZOodereinemVertrieb erworbenhat,gemäßdenBedingungendieserbeschränktenGarantie(imWeiterenals„Garantie“bezeichnet),dass EIZOundderVertriebnacheige
GARANTIE LIMITÉE EIZO NANAO CORPORATION (ci-après dénommé « EIZO ») et les distributeurs autorisés par EIZO (ci-après dénommés«Distributeurs»),sousréserveetconformémentauxtermesdecettegarantielimitée(ci-aprèsdénommée « Garantie »), garantissent à l’acheteur initial (ci-après dénommé « Acheteur initial ») du produit spécifié dans la présente (ci-après dénommé « Produit ») acheté auprès d’EIZO ou de Distributeurs agréés EIZO, que EIZO et ses Di
GARANTÍA LIMITADA EIZONANAOCORPORATION(enlosucesivo“EIZO”)ysusdistribuidoresautorizadosporEIZO(enlosucesivolos “Distribuidores”),conarregloydeconformidadconlostérminosdeestagarantíalimitada(enlosucesivola“Garantía”), garantizanalcompradororiginal(enlosucesivoel“Comprador original”)quecompróelproductoespecificadoeneste documento(enlosucesivoel“Producto”)aEIZOoasusDistribuidores,queEIZOysusDistribuidores,asupropio criterio,repararánosu
GARANZIA LIMITATA EIZONANAOCORPORATION(acuisifaràriferimentodaquiinpoicon“EIZO”)ediDistributoriautorizzatidaEIZO(a cuisifaràriferimentodaquiinpoicon“Distributori”)garantiscono,secondoiterminidiquestagaranzialimitata(acuisi faràriferimentodaquiinpoicon“Garanzia”)all’acquirenteoriginale(acuisifaràriferimentodaquiinpoicon“Acquirente originale”) che ha acquistato il prodotto specificato in questo documento (a cui si farà riferimento da
BEGRÄNSAD GARANTI EIZO NANAO CORPORATION (nedan kallat “EIZO”) och EIZOs auktoriserade distributörer (nedan kallade “Distributörer”) garanterar i enlighet med villkoren i denna begränsade garanti (nedan kallad “Garantin”) den ursprungligeköparen(nedankalladden“Ursprunglige köparen”)somköptedenidokumentetspecificeradeprodukten (nedankallad“Produkten”)frånEIZOellerDistributörer,attEIZOellerDistributörerenligtegetgottfinnandekostnadsfritt antingenreparer
有限责任保证书 EIZONANAO 有限公司（以下简称 EIZO ）和 EIZO 授权的经销商（以下简称 经销商 ），接受并依照本有限责任保证书 （以下简称 保证书 ）之条款，向从 EIZO 和经销商购买本文中所规定产品（以下简称 产品 ）的原买方（以下称 原买方 ） 提供保证 ：在保证期内（规定如下），如果原买方发现 (i) 按本产品所附使用说明书（以下简称 用户手册 ）所述方式正常 使用本产品过程中，本产品出现故障或损坏；或 (ii) 按用户手册所述方式正常使用本产品过程中，本产品的液晶显示屏 (LCD) 及亮度未能达到用户手册中所述的推荐亮度时，EIZO 和经销商根据其独自的判断免费修理或更换该产品。 本 保 证 期 限 定 为 自 购 买 本 产 品 之 日 起 的 五 (5) 年（ 以 下 简 称 保 证 期 限 ）， 亮 度 的 保 证 期 限 定 为 本 产 品 的 使 用 时 间 在 10000 小 时 以 下 ( 含 10000 小 时 )( 亮 度 为 400cd/m2， 色 温 为 开 氏 温 度 7500) 或 20000 小 时 以 下 ( 含 20000 小 时 )( 亮 度 为
China Measures for RoHS Compliance in ChinaRoHS 关于电子信息产品污染控制标识 本标识根据「电子信息产品污染控制管理办法」，适用于在中华人民共和国销售的电子信息产品。标识中央的 数字为环保使用期限的年数。只要您遵守该产品相关的安全及使用注意事项，在自制造日起算的年限内，不会 产生对环境污染或人体及财产的影响。上述标识粘贴在机器背面。 • 有毒有害物质或元素的名称及含量 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 （Pb） （Hg） （Cd） （Cr（VI）） （PBB） （PBDE） 印刷电路板 × ○ ○ ○ ○ ○ 机箱 ○ ○ ○ ○ ○ ○ 液晶显示器 × × ○ ○ ○ ○ 其他 × ○ ○ ○ ○ ○ ○ ：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 规定的限量要求以下。 × ：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 规定的限量要求。 ( 企业可在此处 , 根据实际情況对上表中打“×” 的技术原因进行进一步说明 ) 54 Appe
