User’s Manual Touch Panel Color LCD Monitor It shall be assured that the final system is in compliance to IEC60601-1-1 requirements.
English SAFETY SYMBOLS This manual uses the safety symbols below. They denote critical information. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety.
English TABLE OF CONTENTS PRECAUTIONS ................................................................................... 4 1. INTRODUCTION ..................................................................................... 9 1-1. Features ........................................................................................................9 1-2. Package Contents..........................................................................................9 1-3. Controls & Connectors .......................
English PRECAUTIONS IMPORTANT! x This product has been adjusted specifically for use in the region to which it was originally shipped. If operated outside the region to which it was originally shipped, the product may not perform as stated in the specifications. x To ensure personal safety and proper maintenance, please read this section and the caution statements on the unit (refer to the figure below).
English WARNING If the unit begins to emit smoke, smells like something is burning, or makes strange noises, disconnect all power connections immediately and contact your dealer for advice. Attempting to use a malfunctioning unit can be dangerous. Do not dismantle the cabinet or modify the unit. Dismantling the cabinet or modifying the unit may result in electric shock or burn. Refer all servicing to qualified service personnel.
English WARNING To avoid danger of suffocation, keep the plastic packing bags away from babies and children. Use the enclosed power cord and connect to the standard power outlet of your country. Be sure to remain within the rated voltage of the power cord. Not doing so may cause in fire or electric shock. To disconnect the power cord, grasp the plug firmly and pull. Never tug on the cord, doing so may cause damage and could result in fire or electric shock.
English WARNING When attaching an arm stand, please refer to the user’s manual of the arm stand and install the unit securely. Not doing so may cause the unit to come unattached, which may result in injury or equipment damage. When the unit is dropped, please ask your dealer for advice. Do not continue using a damaged unit. Using a damaged unit may result in fire or electric shock. When reattaching the tilt stand, please use the same screws and tighten them securely.
English CAUTION Do not touch the plug with wet hands. Touching them may result in electric shock. Use an easily accessible power outlet. This will ensure that you can disconnect the power quickly in case of a problem. Periodically clean the area around the plug. Buildup of dust, water, or oil on the plug may result in fire. Unplug the unit before cleaning it. Cleaning the unit while it is plugged into a power outlet may result in electric shock.
English 1. INTRODUCTION Thank you very much for choosing an EIZO Color Monitor. 1-1. Features • Dual inputs compliant • DVI (p.35) Digital input (TMDS (p.36)) compliant. • Horizontal scanning frequency: Vertical scanning frequency: Resolution: Analog input 30 - 81 kHz Digital input 30 - 65 kHz Analog input 49.5 - 75.5 Hz Digital input 59 - 61 Hz (VGA text: 70 Hz) 1 M pixels (1280 dots x 1024 lines) • Auto Adjustment compliant • Support to sRGB (p.
English 1-3. Controls & Connectors Front (1) Control Panel SIGNAL 1-2 MODE AUTO ENTER (2) (3) (4) (5) (1)ScreenManager® (2)SIGNAL1-2 10 (6) (7) (8) Monitor Adjustment menu (p.16) Input Signal Selection Button Switch the input signals when connecting 2 PCs. (p.15) (3)MODE Mode Button Show or switch the color mode. (p.23) (4)AUTO Auto Adjustment Button Adjust the screen to appropriate condition automatically. (analog input only) (5)ENTER Enter Button Show the ScreenManager on the screen.
English Rear (13) (14) (15) Bottom (9) (10) (11) (12) (9) Power Connector Connect the power cord. (10) DVI-D Connector (SIGNAL1) Connect the optional digital cable. (11) D-Sub mini 15 pin Connector (SIGNAL2) Connect the enclosed analog cable (MDC87) (12) RS-232C port Connect the enclosed touch panel cable (FD-C38). (13) Hole for TP1 (14) Hole for installing the lead of the TP1 (Optional Touch Panel Pointer).
English 2. CABLE CONNECTION 2-1. Before connecting Before connecting your monitor to the PC, change the display screen settings (resolution (p.35) and frequency) in accordance with the charts below. NOTE x The lower display modes like 640x 480, automatically enlarge to the maximum display mode (1280 x 1024), and some lines of the characters may become fuzzy. In this case, use function (p.22) to make the lines clear.
English 2-2. Connecting the signal cable NOTE x Be sure that the power switches of both the PC and the monitor are OFF. 1. Plug the signal cable into the connector at the rear of the monitor and the other end of the cable into the video connector on the PC. After connecting, secure the connection with the screw-in fasteners. Digital Signal Input Connecter 3. Power Cord Analog Signal Input Connecter 1. Signal Cable 2.
English 3. Plug the power cord into the power connector on the rear of the monitor. Then, plug the other end of the cord into a power outlet. WARNING Use the enclosed power cord and connect to the standard power outlet of your country. Be sure to remain within the rated voltage of the power cord. Not doing so may cause in fire or electric shock. The equipment must be connected to a grounded main outlet. Not doing so may cause in fire or electric shock. 4.
English NOTE x Whenever finished, turn off the PC and the monitor. Disconnecting the monitor from the power supply is recommended to save energy completely. x Adjust brightness of the screen depending on the brightness of your environment. Too dark or too bright of a screen can cause eyestrain. x Be sure to take adequate rests. A 10-minute rest period each hour is suggested. 2-3. Touch Operation Point and touch with one finger only. NOTE x Do not touch the screen while the computer is starting.
English 3. ScreenManager 3-1. How to use the ScreenManager ScreenManager Main Menu Control Buttons Left, Down, Up, Right SIGNAL 1-2 MODE AUTO Auto Adjustment Button 1. ENTER Enter Button Entering the ScreenManager Press the Enter Button once to display the main menu of the ScreenManager. 2. Making Adjustments and Settings (1) Select the desired sub menu icon using the Control Buttons and press the Enter Button. The sub menu appears.
English 3-2. Adjustments and Settings The following table shows all the ScreenManager’s adjustment and setting menus. “*” indicates adjustments of analog input only. Main menu Screen Sub menu Reference Clock * Phase * Position * Range Adjustment * 4-1. Screen Adjustment (p.20) Smoothing Color Brightness 4-2. Color Adjustment (p.23) Color Mode x Custom Temperature Gamma Saturation Hue Gain Reset x sRGB Others *1 Input Signal Set the input signal selection of automatic or manual (p.
English 3-3. Useful Functions Adjustment Lock Use the “Adjustment Lock” function to prevent any accidental changes. Locked function x Auto Adjustment Button adjustments and settings in the ScreenManager. Unlocked function x Adjustment of brightness by the Control Buttons. x Input Signal Selection Button x Mode Button [To lock] (1) Switch off the monitor’s power by the power switch on the control panel. (2) Press on the Auto adjustment button while switching on the monitor’s power.
English EIZO Logo display Enables to display the EIZO logo for a while when switching on the monitor (Default is no logo). If you desire to display or undisplay this logo, use this function. [To display] (1) Switch off the monitor’s power by the Power switch on the control panel. (2) Hold down the Enter button once again and turn the power back on. [To undisplay] (1) Switch off the monitor’s power by the Power switch. (2) Hold down the Enter button once again and turn the power back on.
English 4. ADJUSTMENT The monitor displays the digital input image correctly based on its pre-setting data. Adjust the brightness (p.23). 4-1. Screen Adjustment Screen adjustments for the LCD monitor should be used in suppressing screen flickering and also for adjusting the screen to its proper position. There is only one correct position for each display mode. It is also recommended to use the ScreenManager function when first installing the display or whenever changing the system.
English 2. We recommend setting the desktop pattern to that as shown in the diagram below. NOTE x More precise adjustment is available for using the “Screen Adjustment program” utility software. It can be downloaded from the EIZO homepage (http://www.eizo.com/). 3. Adjust by using menu in the ScreenManager. (1) Vertical bars appear on the screen o Use the (p.35) adjustment. Select the and eliminate the vertical bars by using the Right and Left of the Control Buttons.
English (3) The screen position is incorrect. o Use the adjustment. The correct displayed position of the monitor is decided because the number and the position of the pixels are fixed. The “Position” adjustment moves the image to the correct position. Select and adjust the position by using the Up, Down, Right and Left Buttons.
English 4-2. Color Adjustment In the analog input, perform the “Range Adjustment” (p.22) before making the color adjustments. The menu in the ScreenManager enables to change the color of the screen. By using the , the adjustment mode can be selected from (to adjust the color settings according to your preference) and mode. NOTE x Allow the LCD monitor to stabilize for at least 20 minutes before making image adjustments.
English Menu Gamma (p.35) Color Mode Custo sRGB m - Function Descriptions To set the gamma value Adjustable range 1.8 a 2.6 NOTE x If setting the gamma value, the using the monitor in the digital signal input is recommended. If using the monitor in the analog input signal, set the gamma value from 1.8 to 2.2. Saturation - To change the saturation -128 a 127 Setting the minimum level (-128) turns the image to the monochrome.
English 5. ATTACHING A STAND The LCD monitor can be used with other stand by removing the tilt stand and attaching the stand to the LCD monitor. NOTE x If you will use the other stand, confirm the followings to the manufacturers before selecting. - Hole spacing on the stand mounting: 100 mm x 100 mm (VESA compliant) - Supportable Weight: Total weight of the monitor (without stand) and attaching equipment such as a cable - TÜV/GS approved stand x Please connect cables after attaching a stand.
English 4. Attach a stand to the LCD monitor securely with the same screws. stand 4 Mounting Screws: M4 x 12 mm 26 5.
English 6. TROUBLESHOOTING If a problem persists even after applying the suggested remedies, contact an EIZO dealer. The latest FAQ information is supplied on EIZO homepage (http://www.eizo.com/). x No Picture Problems Problems 1. No picture x Indicator status: Off x Indicator status: Blue x Indicator status: Yellow Flashing 2. Following messages appear. (Error messages shown below will remain on the screen for 40 seconds.
English Imaging problems x Problems Points to check with possible solutions 3. Display position is incorrect. Adjust the image position using the (p.22) The two display modes, VGA 720 x 400 (70 Hz) and 320 x 200 (70 Hz), have the same signal timings. Using this adjustment selects the appropriate display mode. (This function effects only when the resolution is VGA 720 x 400 (70 Hz) or 320 x 200 (70 Hz).
English x Other problems Problems Points to check with possible solutions 10.The cannot be selected. is disabled when the screen is displayed in the 1280 x 1024. 11.The Enter Button does not operate. The adjustment lock is probably on. To unlock: switch the LCD monitor off. Then, while pressing the Auto Adjustment Button switch, the power on. (p.18) The adjustment lock is probably on. To unlock: 12.The Auto Adjustment Button does switch the LCD monitor off.
English Problems 15.Cursor position is not correct. / Cursor jumps. Points to check with possible solutions When cursor position is incorrect or cursor jumps, turn off and on the monitor. x The drawing touch (touch operation with dragging the finger on the touch panel) to draw the picture may cause incorrect cursor position. x Changing the position or angle of the monitor while the monitor operation will cause cursor jump. x Keep metals away from the panel surface.
English 7. CLEANING Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime. NOTE x Never use thinner, benzene, ethanol, abrasive cleaners, or other strong solvents, as these may cause damage to the cabinet or panel. x Never use spray for preventing static electricity, as it may influence the sensibility of the touch panel. Cabinet To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild detergent.
English 8. SPECIFICATIONS LCD Panel 48 cm (19.0 inch), TFT color LCD panel with Anti-Glare Hard Coating, Viewing Angle: H: 178°, V: 178° (CR≥10) Dot Pitch 0.294 mm Horizontal Scan Frequency Analog: 30 ~ 81 kHz (Automatic) Digital: 30 ~ 65 kHz Vertical Scan Frequency Analog: 49.5 ~ 75.5 Hz (Automatic) Digital: 59 ~ 61 Hz, (VGA Text : 70Hz) Resolution 1 M pixels (1280 dots x 1024 lines) Dot Clock (Max.) Analog: 135 MHz Digital: 109 MHz Display Colors 16 million colors (max.) Display Area 376.3 mm (H) ×301.
English Default settings Brightness 100% Smoothing 3 Temperature Off (normal white: approx. 6500 K) Input Signal Auto Off Timer Disable Language English Optional Touch Panel Pointer Dimensions TP1 Unit mm (inches) 8.
English Pin Assignment D-Sub mini 15 pin connector 3 4 5 15 1 2 8 9 10 7 6 14 13 12 11 Pin No. 1 2 3 4 5 Signal Red video Green video Blue video Ground No pin Pin No. 6 7 8 9 10 Signal Red ground Green ground Blue ground No pin Ground Shorted Pin No. 11 12 13 14 15 Signal Ground Shorted Data (SDA) H. Sync V. Sync Clock (SCL) DVI-D Connector 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Pin No.
English 9. GLOSSARY Clock With the analog input signal display, the analog signal is converted to a digital signal by the LCD circuitry. To convert the signal correctly, the LCD monitor needs to produce the same number clock pulse as the dot clock of the graphics system. When the clock pulse is not correctly set, some vertical bars of distortion are displayed on the screen. Color Temperature (Temperature) Color Temperature is a method to measure the white color tone, generally indicated in degrees Kelvin.
English Range Adjustment The Range Adjustment controls the level of output signal range to display the whole color gradation. Resolution The LCD panel consists of a fixed number of pixel elements which are illuminated to form the screen image. The EIZO L760T-C display panel consists of 1280 horizontal pixels and 1024 vertical pixels. At a resolution of 1280 x 1024, all pixels are displayed as a full screen.
APPENDIX/ANHANG/ANNEXE Preset Timing Chart for Analog input Timing-Übersichten für Analog Eingang Synchronisation des Signaux pour Analog numerique Based on the signal diagram shown below 16 factory presets have been registered in the monitor's microprocessor. Der integrierte Mikroprozessor des Monitors unterstützt 16 werkseitige Standardeinstellungen (siehe hierzu die nachfolgenden Diagramme).
For U.S.A, Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZO NANAO TECHNOLOGIES INC. 5710 Warland Drive, Cypress, CA 90630 Phone: (562) 431-5011 declare that the product Trade name: EIZO Model: FlexScan L760T-C is in conformity with Part 15 of the FCC Rules.
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörige Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden.
Recycle Auskunft Die Rücknahme dieses Produktes nach Nutzungsende übernimmt EIZO in Deutschland zusammen mit dem Partner eds-r gmbh rücknahmesysteme. Dort werden die Geräte in ihre Bestandteile zerlegt, die dann der Wiederverwertung zugeführt werden. Um einen Abholtermin zu vereinbaren und die aktuellen Kosten zu erfahren, benutzen Sie bitte folgende Rufnummer: 02153-73 35 00. Weitere Informationen finden Sie auch unter der Internet-Adresse: www.eizo.de.
