User’s Manual FlexScan T561 Color Display Monitor
SAFETY SYMBOLS This manual uses the safety symbols below. They denote critical information. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety. Copyright© 2000 by EIZO NANAO CORPORATION. All rights reserved.
CONTENTS PRECAUTIONS ............................................................................. 4 1. INTRODUCTION ............................................................................ 9 2. ENGLISH 1-1. Features ....................................................................................................... 9 1-2. Package Contents ........................................................................................ 9 1-3. Controls & Connectors .........................................
PRECAUTIONS IMPORTANT! • This product has been adjusted specifically for use in the region to which it was originally shipped. The performance of the product, (i.e. picture geometry, picture positioning and color convergence and purity in the case of color monitors) is optimally adjusted to the earth’s magnetic field of the specific destination. If operated outside the region to which it was originally shipped, the product may not perform as stated in the specifications.
WARNING ENGLISH • Keep small objects away from the monitor. Small objects may accidentally fall through the ventilation slots into the cabinet, leading to fire, shock, or equipment damage. • Keep liquids away from the monitor. Spillage into the cabinet may result in fire, electric shock, or equipment damage. If an object or liquid falls/spills into the cabinet, unplug the monitor immediately. Have the unit checked by a qualified service engineer before using it again.
WARNING • Use the enclosed power cord. If using the power cord other than the enclosed one, use the following cord. [USA and Canada] Use a UL LISTED/CSA LABELED or CERTIFIED power cord set meeting the following specifications. * Rating: min. 125 V, 10 A * Length: max. 2.0 m * Plug type: NEMA 5-15P, Parallel blade, Grounding type, 125 V, 10 A * Type: SVT [Europe] Use a proper European standard approved power cord meeting the following specifications. * Rating: min. 250 V, 10 A * Length: max. 2.
CAUTION ENGLISH • Handle with care when carrying the monitor. * Disconnect the power cord, signal cables and remove the optional i·Sound™ sound unit (if applicable). Moving the monitor with the cord attached or lifting it by the i·Sound™ sound unit is dangerous. It may result in injury or equipment damage. * Note that the monitor is heavier at the front than at the rear. Do not move it alone. Always work with another person. * The screen is optically coated to reduce glare.
CAUTION • Do not touch the plug with wet hands. Touching the plug with wet hands is dangerous and can cause electrical shock. • Use an easily accessible power outlet. This will ensure that you can disconnect the power quickly in case of a problem. • Unplug the monitor before cleaning it. Cleaning the monitor while it is plugged into a power outlet may result in electric shock.
1. INTRODUCTION Thank you very much for choosing EIZO FlexScan T561. 1-1. Features ENGLISH • High contrast natural flat type CRT. • Dual inputs with individual color configuration. 1-2. Package Contents Please contact your local dealer for assistance if any of the listed items are missing or damaged. • Monitor • Signal Cable (MD-C87/MD-C100) • Power Cord • User’s Manual • EIZO CRT Utility Disk • Warranty Registration Card • Please retain the packing materials for future transference. 1.
1-3. Controls & Connectors Front (1) ScreenManager™ (1) (2) BNC/D-SUB Selection Button (3) AUTO-SIZING Button (4) Power Terminal Covers for the Optional i·Sound Sound Unit.
2. INSTALLATION 2-1. Connecting the monitor to the PC 1. Plug the signal cable into the connector at the rear of the monitor and the other end of the cable into the video connector on the PC. After connecting, secure the connection with the screw-in fasteners.
2. Plug the power cord into the power connector at the rear of the monitor. Then plug the other end of the cord into a power outlet. WARNING • The equipment must be connected to a grounded main outlet. • Use the enclosed power cord. If using the power cord other than the enclosed one, use the following cord. [USA and Canada] Use a UL LISTED/CSA LABELED or CERTIFIED power cord set meeting the following specifications: * Rating: min. 125 V, 10 A * Length: max.2.
2-2. Getting Ready for Operation Try each setting procedure if necessary in the following cases. Press the AUTO-SIZING button on the front panel. The AUTO-SIZING function centers the displayed image, aligning the image’s borders with respect to the monitor frame. In general, press the AUTO-SIZING button whenever changing the graphics board or the resolution p.30), or when image size and/or position is incorrect.
3. SCREEN ADJUSTMENT • Allow the monitor to stabilize for at least 30 minutes before making image adjustments. 3-1. How to use the ScreenManager Use the control pad on the front panel. The control pad can be pressed in 5 directions, “Enter”, “Up”, “Down”, “Left” and “Right”. Up Left Enter Right Down 1. Entering the ScreenManager. Display the ScreenManager Main menu by pressing the “Enter” of the control pad. Main menu Æ Main menu displays the current connector type and frequency of the input signal.
3-2. Adjustments and Settings Main menu Sub menu Adjustments and Settings See page — Screen contrast and brightness* — Size — Screen size — Position — Screen position — Screen Side Pin. Side pin balance — Trapezoidal Distortion — Tilt Inclination Convergence Convergence Moiré Reduction Moiré Color Others — p.29) — p.29) — Fine Contrast To brighten the photo or picture image. p.16 Signal Filter To decrease the slightly shadowed images or characters. p.
< Screen > • To brighten the photo or picture image < Fine Contrast > Select “Picture Mode”. * Select “Text Mode” to display the text on word processor or calculating software. * The AUTO-SIZING button can be customized to active this function easily (See page 19). • To decrease a slightly shadowed image or character When the characteristics of the graphics board does not match those of the monitor, the characters and images displayed may have a slight shadow on their right side.
< Color > • To set the color temperature ENGLISH Temperature can be set from 4,000 K to 10,000 K, in 500 K increments. (Including the 9,300 K default setting.) < Temperature> Select “Color temperature”. “Standard” mode • To adjust each color , (Red, Green and Blue) Adjust the “Cutoff”p.29) and “Gain”p.29), and make appropriate color tone. (1) First, set the monitor to maximum contrast and brightness. (2) “Custom” mode < Temperature> Set the color temperature that is close to the desired color.
< Others > • To set the power save There are two power save settings choose the setting which matches your environment. • Do your part to conserve energy, turn off the monitor when you are finished using it. Complete energy use can only be accomplished by disconnecting the monitor’s power supply cord from the plug receptacle. 1. With PC’s power saving system (VESA DPMS p.30)) The monitor detects the signal from the PC and executes the power saving accordingly, as shown in the table below.
• To degauss the monitor • To customize the button function (Auto sizing or Fine Contrast) < Button Setting > Select “Auto Sizing”(Auto sizing function ) or “Fine Contrast”(Brighten the photo or picture image ). • To adjust the menu position of the ScreenManager < Menu Position > Adjust the menu position as desired by using the control pad. • To return to the factory default setting < Reset > Select “Reset”. Default settings are as follows. Contrast and Brightness. Moiré.
3-3. Special Function Shortcut Keys The brightness and contrast can be adjusted by pressing the Up, Down, Left and Right keys of the control pad directly. Press the center of the control pad to save and exit the settings after the adjustment. Adjustment Lock Use the “Adjustment Lock” function, to prevent any accidental changes. Locked function Unlocked function • Adjustments and settings in the ScreenManager. • AUTO-SIZING button. • Adjustment of contrast and brightness by the shortcut keys.
4. CONNECTING TWO PCs TO THE MONITOR Two PCs can be connected to the T561 through the BNC/D-Sub input connections on the back of the monitor. (Example) Apple Macintosh (Blue & White) ENGLISH Æ Standard graphics board MD-C53A (Optional) Selecting the active input The BNC/D-Sub selection button on the front panel can be used to select either the BNC or D-Sub connection as the active input. Every time the button is pressed, the input changes.
5. TROUBLESHOOTING If a problem persists even after applying the suggested remedies, contact an EIZO dealer. Problems 1. No picture • Indicator status: Off • Indicator status: Green • Indicator status: Flashing Green / Yellow • Indicator status: Flashing Yellow 2. Following messages appear. • “No signal detected” error message appears. • “Out of range” error message appears. Whenever an error signal message appears, the signal frequency will be displayed in red. (Example) 22 5.
Problems Points to check with possible solutions The image vibrates on the screen. Check that the signal cable is properly connected to the PC or graphics board. The monitor may be located close to a device that is generating a magnetic field. Such devices include speakers (other than the EIZO optional i·Sound speaker), electric motors, high-voltage cables, and other monitors. It may be solved by turning off or moving the interfering device, or by relocating the monitor.
Problems Points to check with possible solutions 7. The entire screen appears too dark or bright. Adjust the “Contrast and Brightness” function in the ScreenManager “Main” menu. (p.15) Some signal timing can be the cause of this problem. To correct this, turn off the monitor, then hold down the “down” arrow key while turning on the monitor again. This will change the signal timing and brighten the screen. If the above operation is repeated, the screen becomes dark again.
Problems Points to check with possible solutions The Adjustment Lock is probably on. To unlock: Turn off the monitor power, then hold down the AUTO-SIZING button once again and turn the power back on. (p.20) 11. Two horizontal hairlines are visible on the screen. These are damper wires. 12. Faint black vertical lines are visible on the screen. The aperture grille may be misaligned. Shock or vibration during transport may, in some cases, cause the aperture grille to fall out of alignment.
6. CLEANING Periodic cleaning is recommended to keep the monitor looking new and to prolong its operational lifetime. Clean the cabinet and CRT areas as follows: WARNING • Keep liquids away from the monitor. Spillage into the cabinet may result in fire, electric shock, or equipment damage. If an object or liquid falls/spills into the cabinet, unplug the monitor immediately. Have the unit checked by a qualified service engineer before using it again.
7. SPECIFICATIONS CRT Power Supply Power Consumption Input Connector Input Signal Sync Video Signal registration Plug & Play Dimensions Weight Temperature Humidity Certifications and Standards 100-120 VAC UL/C-UL, FCC-B, DHHS, TCO’99, EPA ENERGY STAR® Program 220-240 VAC CE, CB, TÜV Rheinland/GS, TCO’99, EPA ENERGY STAR® Program, TÜV Eco Circle 2000 * Display size can be set by the user through microprocessor control panel.
mm (inches) Dimensions 302.1 (11.9) 410 (16.1) 323 (12.7) 413 (16.3) 10° 4° 242 (9.5) 122 (4.8) φ265 (φ10.4) 46.9 (1.8) 74.9 (2.9) 439 (17.3) FRONT 45° 45° SIDE TOP Pin Assignment * D-Sub mini 15 pin connector No. Signal No. 1 Red Video Signal 8 Blue ground 2 Green Video / 9 No pin Green composite sync 10 Ground 3 Blue video 11 (Shorted) 4 Ground 12 Data (SD) 5 No pin 13 H. Sync / H/V Composite sync 6 Red gound 14 V.
8. GLOSSARY Color Temperature Convergence Convergence is the monitor’s ability to precisely illuminate specific phosphors and line them up properly in order to produce pure color. Cutoff and Gain Monitors use red, green and blue (R, G, and B) to convey color information. They use an additive method to combine different amounts of the primary colors to produce a desired color. In other words, monitors start with no light (black) and add percentages of red, green and blue to make colors.
Resolution Resolution is expressed as the number of dots (pixels) displayed on the screen. A larger number of dots produces a more sharply defined (a higher-resolution) image. Notes that for a given screen size the dot size decreases as the number of dots increases: a 640 x 480 (dot x line) resolution uses larger pixels than a 1024 X 768 resolution. The display size of a given font therefore varies according to the resolution. Higher resolutions allow you to display more information on the screen.
9.
MEMO 32
Congratulations! You have just purchased a TCO’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs.
For U.S.A, Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZO NANAO TECHNOLOGIES INC. 5710 Warland Drive, Cypress, CA 90630 Phone: (562) 431-5011 declare that the product Trade name: EIZO Model: FlexScan T561 is in conformity with Part 15 of the FCC Rules.
Hinweis zur Ergonomie : Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1/59-98, EK1/6098 mit dem Videosignal, 1280 Punkte x 1024 Zeilen, RGB analog, 0,7 Vp-p und mindestens 85,0 Hz Bildwiederholfrequenz, non interlaced. Weiterhin wird aus ergonomischen Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast.) PTB Hinweis Eigensichere Kathodestranlröhre nach Anlage III Röntgenverordnung.
